Liqui Moly Diesel de-carb Ford Ranger 3.2TD clogged diesel

Автокөліктер мен көлік құралдары

Simple way to decarb your Diesel engine by removing the throttle intake and spraying liqui moly in whilst the vehicle is running. Saves removing the entire top end of the engine apart for cleaning. 2014 ford ranger used.
Instagram→ / mikeandmarks4x4
Facebook→ / mikeandmarks4x4
Website → www.mikeandmarks4x4.com/
Channel Home Page → / @mikeandmarks4x489

Пікірлер: 67

  • @shanea9613
    @shanea96134 жыл бұрын

    I just did mine, a 2014 jeep Grand Cherokee 3.0 diesel. I noticed a difference with the idle feels better already. Mine's got 170000kms. Well worth it, I could see a difference inside, cleaned it up nice.

  • @ifithegr8

    @ifithegr8

    3 жыл бұрын

    What pipe did you remove to use it?

  • @kayakwesty
    @kayakwesty Жыл бұрын

    I use 2 cans at oil my changes. Thank you for the video. Viewer from the States.

  • @brandonjcollins1062
    @brandonjcollins10624 жыл бұрын

    I’m thinking about giving this a go so thanks for the video mate. Appreciate it!

  • @mikeandmarks4x489

    @mikeandmarks4x489

    3 жыл бұрын

    Good luck!!

  • @mickill2
    @mickill24 жыл бұрын

    I use it after every service,on both inlet manifold and the turbo,does a good job well worth the money.

  • @mudslingaaa8303

    @mudslingaaa8303

    3 жыл бұрын

    Where about would you pump it into the turbo housing ?

  • @RangerDanger720

    @RangerDanger720

    2 ай бұрын

    Dammm it says not to do it near heat because its flammable

  • @rogerramjuice2562
    @rogerramjuice25623 жыл бұрын

    Do you have a video on cleaning injectors on the same model vehicle?

  • @Leo70780
    @Leo707806 ай бұрын

    I've heard CRD Fuel Enhancer additive is very good , and cleans your whole fuel system . It's from Cost Affective Maintenance 👍

  • @andmetalforall2763
    @andmetalforall27632 жыл бұрын

    Hey mate, just about to do this to my Dmax, is it recommended to change the oil & filter afterwards?

  • @dzsemadhs1816
    @dzsemadhs1816 Жыл бұрын

    I use this product few days ago my MPG 27 and after few days of driving i MPG 47 after cleaning get better and car run nice and quet than before cleaning

  • @ryannarvo5076
    @ryannarvo5076 Жыл бұрын

    Did you getva mate to get it to 2000rpm whilest you sprayed?

  • @hughgrant2906
    @hughgrant290626 күн бұрын

    When i take the intske hose off to throttle body then start the engine i cant rev it because the throttle body closes so csnt gdt that hose down there? Why is urs not closing is my throttle body faulty? Thanks

  • @bitpri05
    @bitpri053 жыл бұрын

    I have also used this product. While the solvent is very effective on Diesel carbon, using as per the label does not effectively clean. I use the spray to soften the carbon then use cleaning pads or cloths to wipe it out. Use a rifle bore cleaning rod to get further inside with cloth wrapped around it or fully dismantle as i did this weekend - use the solvent to clean egr - intake - parts ect

  • @mikeandmarks4x489

    @mikeandmarks4x489

    3 жыл бұрын

    How long did it take to fully dismantle? I like the gun bore cleaning idea!

  • @bitpri05

    @bitpri05

    3 жыл бұрын

    Mike and Mark's 4X4 it depends on the car i guess and how far you dismantle - for me i took out the egr - throttle body to enable a fairly easy access to the intake. Spray and wipe pretty much. For me maybe a 10 min dismantle

  • @mikeandmarks4x489

    @mikeandmarks4x489

    3 жыл бұрын

    Wow, I’ve heard of others taking off the head and it took a full day to remove/clean/replace!

  • @bitpri05

    @bitpri05

    3 жыл бұрын

    Mike and Mark's 4X4 sorry - not the whole intake manifold or heads. Just the throttle body and egr to access the back of the intake easier. From my experience the build up decreases progressively after the egr I expect that the ease or utility of this solution varies from car to car but for me works fine and certainly in contrast to the spray only option is a massive value add

  • @therukugorillazaotearoa_

    @therukugorillazaotearoa_

    4 ай бұрын

    Can you make a video mate please

  • @marks.Landing
    @marks.Landing3 жыл бұрын

    Thanks mate I've got an old 07 ranger that's been absolutely bullet proof, 223k and drinking deisel like it's fukin free, got some liqui moly and air flow sensor cleaner and new air filter, only getting 450k a tank in 5th gear at 90klms 1hour trip each way fukin driving me insane

  • @tomdom_0143

    @tomdom_0143

    2 жыл бұрын

    Did the clean help at all?

  • @stevo3644
    @stevo36443 жыл бұрын

    An honest appraisal of the liquid moly cleaner. Looking at that you would have to use two or three can to clean it properly. I’ve just fitted a ryco catch can kit to my ranger at 50,000 km so hopefully it won’t get as bad.

  • @JudasBytes

    @JudasBytes

    Жыл бұрын

    how is the oil catch can performing?

  • @stevo3644

    @stevo3644

    Жыл бұрын

    @@JudasBytes - the system works very well and highly recommend to get the full kit including moulded hoses.

  • @nikfish1
    @nikfish14 жыл бұрын

    Mate, where did you buy this? Supercheap, Repco, Autobarn, Bursons - don't seem to carry this specific product any more?

  • @mikeandmarks4x489

    @mikeandmarks4x489

    4 жыл бұрын

    Autobarn do carry it, it’s hard to find amongst all the range they have these days! Make sure to get the right one (diesel/petrol) as it’s a sure fire way to blow your motor

  • @lolorick5885
    @lolorick5885 Жыл бұрын

    To decarbonize your engine intake use oven cleaner, which is the best such as something like Mr Muscle is the best solution by far. I do use liquid Moly only for fuel treatment additives

  • @rvvinuya
    @rvvinuya2 жыл бұрын

    When u removed the intercooler piping, did the check engine light come ON? Thankyou :)

  • @donadami2017

    @donadami2017

    2 жыл бұрын

    it didnt when i did my

  • @MetoTautea
    @MetoTautea2 ай бұрын

    Thanks sir👍

  • @danscullion2539
    @danscullion25394 жыл бұрын

    Is it turbo safe? Can it be spayed down through the aircon?? (Past the filter into the turbo?

  • @mikeandmarks4x489

    @mikeandmarks4x489

    3 жыл бұрын

    I wouldn’t suggest using it other than the way is was designed to. We used it precisely to the manufacturer specifications.

  • @timg8938
    @timg89384 жыл бұрын

    G'day Mark, do either of you gents have any suggestion/input on the cost/benefits of a "catch can" or oil separator? They claim to prevent the buildup you're talking about this video. I've seen some on Diesel Care . com .au - any idea of their reliability?

  • @mikeandmarks4x489

    @mikeandmarks4x489

    4 жыл бұрын

    I have asked a ford engineer this exact question and his response was ‘it’s a waste of time’. Diesels have been around for over 100 years without them. Each to their own though.

  • @creativelight-4002

    @creativelight-4002

    4 жыл бұрын

    Installed one in VW tdi diesel and I can assure you it did a great job taking not I check intake for 6 month without and 6 month after installing still getting dirty but much more less than without one buy a good oil catch can with baffling and filter

  • @Tom74FFV

    @Tom74FFV

    4 жыл бұрын

    @@creativelight-4002 I also have separator oil for TDCI and super www.ford-focus.cz/forum/viewtopic.php?p=1164495#p1164495

  • @baxr6GT

    @baxr6GT

    3 жыл бұрын

    Lol that ford engineer is an idiot, yes diesel have been around for 100s of years, but not common rail diesels and diesels with egr’s, that what’s causing the intake to gunk up, the reason they’re so unreliable these days is because of the build up and it blocking the intake

  • @TheBobinn

    @TheBobinn

    3 жыл бұрын

    Catch can is great, the oil is what is making it stick so the build up is alot less, if you have an egr then consider having it deleted along with the particulate filter(if u can pass MOT without)

  • @moisty254
    @moisty2543 жыл бұрын

    This is where you need one of those bowel inspection cameras to do a before and after

  • @mikeandmarks4x489

    @mikeandmarks4x489

    3 жыл бұрын

    I reckon we’ll do this, good idea!

  • @moisty254

    @moisty254

    3 жыл бұрын

    @@mikeandmarks4x489 $50 for a 5m endoscope camera, wireless, (wifi) with a 1080p resolution, takes pictures or movies in its app. Got my hands on my puppy the other day, real good 👍

  • @mikeandmarks4x489

    @mikeandmarks4x489

    3 жыл бұрын

    Great! Looks like I’m doing some online shopping...

  • @ChatGPTeeh
    @ChatGPTeeh4 жыл бұрын

    where does the gunk goes after spraying it?

  • @mikeandmarks4x489

    @mikeandmarks4x489

    4 жыл бұрын

    Gets burned through the motor and out the exhaust

  • @Edward-kv8re

    @Edward-kv8re

    4 жыл бұрын

    Through your turbocharger and sometimes fuck it up

  • @scottharvey7607

    @scottharvey7607

    4 жыл бұрын

    Edward how can it go through the turbo? The turbo is before the throttle body. So nothing is going through the turbo.

  • @Edward-kv8re

    @Edward-kv8re

    4 жыл бұрын

    @@scottharvey7607 nice. What comes after the exhaust manifold?

  • @markjennings2315

    @markjennings2315

    3 жыл бұрын

    @@scottharvey7607 Through the exhaust section of the turbo, not the impeller.

  • @nogwajaaa747
    @nogwajaaa7474 жыл бұрын

    I think u should just blank your EGR your engine will thank you for that

  • @mikeandmarks4x489

    @mikeandmarks4x489

    4 жыл бұрын

    Hmmm not too keen on that!

  • @bobbymartin8042

    @bobbymartin8042

    3 жыл бұрын

    Definitely blank EGR and run catch can

  • @marcusbarnes5929

    @marcusbarnes5929

    3 жыл бұрын

    @@mikeandmarks4x489 EGR is why you intake looks like grease. Turn it off in ECU and or blank it off and get a catch can and you will not have to worry about this ever again.

  • @therukugorillazaotearoa_

    @therukugorillazaotearoa_

    4 ай бұрын

    ​@@marcusbarnes5929how long would that last if you blank and get catch can ????

  • @marcusbarnes5929

    @marcusbarnes5929

    4 ай бұрын

    Forever.. no exhaust gas or oil vapour going to intake so would remain clean.

  • @Peter-kp9yp
    @Peter-kp9yp Жыл бұрын

    That's what i dont want to do. Pull it apart. I'm not a mechanic but I've seen a few vids😳 an im thinking, bit the bullet an pull it apart,😅 then put it back together🤞🤣..an then run the spray to get the deeper carbon, trapped beyond the inner mannerfold.

  • @UV65
    @UV652 жыл бұрын

    Diesel use

  • @prinsipotomotif8619
    @prinsipotomotif86192 жыл бұрын

    Close your EGR. Look my video friend. Thanks

  • @fcres5845

    @fcres5845

    2 жыл бұрын

    Post Link for your video

  • @prinsipotomotif8619

    @prinsipotomotif8619

    2 жыл бұрын

    @@fcres5845 kzread.info/dash/bejne/ZmSqmZtpfdvAn84.html Indonesia language

  • @lewisfaulkner436
    @lewisfaulkner436 Жыл бұрын

    Did anybody else’s explode

  • @messenger8279
    @messenger82792 жыл бұрын

    Looks like liquid snake oil to me. :-) No different.

  • @robertorebola7532

    @robertorebola7532

    Жыл бұрын

    Open your eyes mate def not snake oil 🛢️ 😅

  • @messenger8279

    @messenger8279

    Жыл бұрын

    @@robertorebola7532 Its the anti ageing cream of the car industry. 😆

  • @robpk84
    @robpk842 жыл бұрын

    I'm sure it cleans a fair bit of gunk off the intake but isn't anyone concerned about what sucking all that shit into the motor is actually doing to it? I won't be using that product.

  • @markthompson242
    @markthompson2422 жыл бұрын

    What a joke. Remove it and clean it properly.

Келесі