Thanks for your time and effort creating and sharing these vids.

@GavinFreedomLover

3 жыл бұрын

No problem there will be one more on the stators tidying and soldering and trying to run them both together 😃

@NTF-zb9wi

3 жыл бұрын

@@GavinFreedomLover Looking forward to watching that one. :)

It outputs the Voltage the correct way because you have 6 diodes in the 3 phase rectifier. So no matter the direction of rotation, it will always be positive on the positive terminal and negative on the negative terminal.

pleasant series of videos, ive seen a few guys buy the cheap jumper cables rather than waste money on pricey cable.

@GavinFreedomLover

3 жыл бұрын

Yes it was the same price for this stuff as it was crappy 10 amp cable

hello . thankyou for this greate video sir, can i apply more volatage like 48v or more with this system ?

Nice. Where can I find that drawing to download ?

hi this is awesome videos ,cany you tell me the 3 wires you join together are they an earth ,are they used for anything will bit of heat shrink do to cover them. when testing you only test the 3 main wires no earth colin

@GavinFreedomLover

3 жыл бұрын

You need to connect the 3 wires coming out to a DC rectifier which changes the AC power into DC for battery charging.

@colinfinch8716

3 жыл бұрын

@@GavinFreedomLover thankyou

Could you use the unit unmodified and step the voltage down via a transformer? Then use a single phase bridge rectifier?

@GavinFreedomLover

Жыл бұрын

I guess you could do that. I've seen people talk about using an unmolested one in a vertical axis wind turbine because it's suited to the lower RPM, I gave up using these motors because I found that electric bike hubs of the right kind are much much better in every way.

Doesn't going deep on the slots run the risk of arcing; or, do you use hot glue (etc.) later in the video/video series to prevent such arcing?

@GavinFreedomLover

3 жыл бұрын

Thanks for the comment I am knee deep in building a machine then I will get back on this project.

@NTF-zb9wi

3 жыл бұрын

@@GavinFreedomLover Thank you. :) I know what it's like to have to try to juggle projects. :) I didn't word my original question all that well, anyway; in that I didn't clarify that I was referring to "on down the road," when wind & weather could start causing some corrosion. (I do tend to "over-think" things a lot; but, it's also the reason why I've survived for 67 tumultuous years...) When you have the time: I'm curious about the combination of 12/24v & 3 phase. I, admittedly, "know just enough to be dangerous" ;p & I'm learning as I go. Here in the US, 3-phase is (as far as I know) always AC; &, typically, only used in industrial settings. 12/24v is typically DC; &, for most applications, requires the use of an inverter to run anything; but, it's appearing to be great for charging super-capacitors (which are getting more affordable & seem to beat the heck out of having a huge bank of deep cycle batteries.) About my only use for 220/240 is my welding machine, which I'd like to continue to be able to use; but, that might easily become irrelevant, given the current dystopian trajectory of the US. I might be darned lucky to get things done in time to even have lights & refrigeration before "the bottom falls out." Anyway... Do you (and others who might be willing to chime in on this) think this wiring version would work over here; or, should I be looking for a more "US version" of how to set up my wires?

you should measure it with an analog multimeter

Same stator but aluminum winding

@GavinFreedomLover

3 жыл бұрын

You have the same stator, sorry for the delay in replying.

Pernahkah anda memodifikasi yang 36pole 3phase dengan memodifikasi 1phase untuk mengambil kebalikan arah gelombang dengan dengan jembatan penyearah

@GavinFreedomLover

8 ай бұрын

No my friend. I didn't try that. I gave up with these motors. They are not powerful enough. They are good for use in hydro if you get 1,000, RPM spin speed

@rupacarachanel

8 ай бұрын

@@GavinFreedomLover Ok terimaksaih sahabatku yang juh disana untuk sharing salam hangat untuk Anda,Saya sangat kesulitan untuk mencapai 1000RPM dari micro hidro ataupun Air ataupun Angin karena lingkungan ,Tapi saya akan berusaha dari 3phase saya ambil 1phase untuk generator penggerak ,Tapi entahlah

How much watts can this produce?

@GavinFreedomLover

2 жыл бұрын

I have taken it down now , max was about 500 watts but I made some errors in the build could get 800 max in very windy conditions, they only make 1kw at 1000rpm in a hydro setup.

@marcangelodonelo5656

2 жыл бұрын

@@GavinFreedomLover oh wow i was about to ask if that can be applied to microhydro. 1kw is good enough for me. I was just thinking if how much can it generate in a water wheel with a 70liter per minute flow and a height of 3m.

@GavinFreedomLover

2 жыл бұрын

yes they are great for hydro make sure you get the bearing stub from the washing machine.