Great comparison. Nice metal table too!

Awsome video. Thanks for making it. This is the type of info the average back yard mechanic is missing when building a motor. I am currently rebuilding a 2010 600RS and my crank is a fully oiled bearing crank but the parts fiche calls for ISO flex grease. Im guessing I have a different bottom end.

Lets see a how to on rebuilding a crank, true and phase

That was helpful and thanks for the help

Thank you for this.

I need some advice on how to tell if my crank bearings are bad, never had a snowmobile apart to know. I assume the crank with cylinders off should spin smooth and free right?!

"inner sealed bearing seem to work well" LOL

Can I change flywheels to update to make work

Would a 2009 800 crank and pistons work in a 2008 800 engine or would the timing be off like explained on the Etek? I know the flywheel from the 2008 would not work.

So i have a 2009 skidoo summit 800 hill climbing edtion. Well i know the ptex cranks suck so i was wondring can i put a etek crank in and if so what do i need to do to make it work. Thanks

What if you pushed in the little plastic in the crankshaft when try to take off the flywheel need help please??

Wanted to buy some rods off you guys. Can’t seem to find a web site. Where could I find that ?

You can't do the snow x rods on an 850 correct? Cause only brp can rebuild them?

I like the old rotax 583,643 and the 670. Use a rotax 670 in my old yamaha, but i have taken out 4 or 5 conrod bearing on the mag side. Oilpump delite, aprox 1:32 oil mix in the gas, flatslides and short intake, tunnelporting and just a little work to the cylinders, never figuerd out why killing the conrod bearing mag side. Got my hands on one rotax ptek 800, but thats not what i want in my exciter, want a 670 if i figure out what couses t mag problem..

@rockymountainchainsaw

Жыл бұрын

Yeah those older 617, 643, and 670 cranks are great. Not sure what is causing your mag side failures. Those Rotax cranks usually take a lot of abuse before they fail.

well the 1992 mach one had to swap the whole crank none of it was rebuildable coming from the dealer had to exchange the origional crank for a new crank complete. that is interesting that a crank can be pulled apart to repair

@kenhmful

Жыл бұрын

Are u shure. I beleve they are rebuldable, looks a lot like the 670 crank, 670 can be rebuilt, they even put 2 cranks together and make a 4syl out of 2 rotax 670 side by side. Dont knowe for shure witch type off crank cranckshops tripple rotax 670 based race engine has, also has 4syl race engine. One 4syl crankshop race engines has been in norway aprox 15years, 2000cc 2t engine, ive prepped the race track for em to do their first testruns, it blew 1drivebelt each 1/8 run

Looking at an 03 mxz800 renegade (pre rev chassis) is this motor known to fail crank bearings?

@kadenreynolds3137

3 жыл бұрын

no

Who makes the better Crank. Polaris, Cat or Doo? Whats the advantage of each and Cons?

@dirtyfacegeorge9938

4 жыл бұрын

Polaris 850 best crank in the biz

@mikeversluis1347

Жыл бұрын

Yamaha makes the best crank

Funny how many rebuilds those doo's get

So what’s the life span of these 800s. I’m hearing 4000 miles is about it, then 5K to rebuild them ?

@257Tony

Жыл бұрын

I had an 800 HO rebuilt last year, cost me $1800, complete from crank to piston. I pulled the motor, and dropped it off.

When did the isoflex go? Garbage When did they go back to oil?

27 bearings

just get your crankshaft rebuilt by a professional crank rebuilder and make sure their good cheaper than buying a new one and safer than ordering one on line! or if you have a press and know what your doing rebuild your own!

But what is the reason that those wont keep straight and balanced? I have second 800 etec now with 2600km in it and that f**kin engine is already wobling and jumping around.🤬 They are really nice engines from other parts but that crank..

@Pneumamechanical

5 жыл бұрын

Will true & welding keep them straight?

They're all the same all those cranks blow out at 2500 miles they finally got rid of isoflex grease they should have been all oil bearings from the start

@rockymountainchainsaw

Жыл бұрын

Yes they should have been. Isoflex is a pain. Now we are dealing with 850 crank problems and issues. I have about 50 of the 850 non turbo cranks to rebuild atm.

Lets not talk. Thats what u do best. Talk us to death. Ok ok yep yep cam ok cam ok yep do that ok. Get s class room

Some good info here, but U forgot to mention they are all Junk! Arctic Cat puts real cranks in their engines not disposable crap like BRP. Do a video showing how robust the Cat crank is in comparison. If U know for one that is out of the engine for repair!