Lee Turret Press, Primer feed setup
Тәжірибелік нұсқаулар және стиль
I had a viewer comment about primers missing the primer arm and ending up on the floor. I thought this might make a good topic for a video so here it is.
I had a viewer comment about primers missing the primer arm and ending up on the floor. I thought this might make a good topic for a video so here it is.
Пікірлер: 31
Excellent video. Thanks. Just started reloading and this helps a lot.
@FatManLeather
5 ай бұрын
Glad it was useful, remember to always use published load data from a reliable source.
This is the most helpful video I've seen on the Lee Safety Prime. Thanks!
@FatManLeather
Жыл бұрын
I did this video for someone that asked about it, I figured if one person had problems, there were more. I'm glad you found it useful, and thanks for commenting.
This video filled in a lot blanks I had! Thank you sir!
@FatManLeather
3 жыл бұрын
Glad it was useful, another viewer requested this video so I figured there would be others that it would help.
good video. It really helps. Thanks!
@FatManLeather
Ай бұрын
Glad it was useful for you, thanks for watching.
I have the same press but never used it because quite frankly I really didn’t know how to and was a bit intimidated that I’d doing something wrong. Your video was helpful. Thanks!!
@FatManLeather
4 жыл бұрын
Not hard to use at all. Just set up each station and let it rip. I loaded 500 9mm after this video. Feel free to ask any questions.
Thank you, sir. Helped me out a lot.
@FatManLeather
11 ай бұрын
I'm glad it was helpful, I did this video in response to a viewer question.
Good tutorial...Nice job....Good stuff....
@FatManLeather
4 жыл бұрын
Thank you much.
Nother good one Mr T 👍
@FatManLeather
4 жыл бұрын
Thank you.
I’m still using a single stage! Lol! I like the old style primer, I used parts from a new one to rebuild my old one! Lol!
@FatManLeather
4 жыл бұрын
I still use a single stage for a lot of my reloading. I'll have to remember that when these give up on me.
Thank you....I related to you better than those push push . videos... Rick
@FatManLeather
3 жыл бұрын
Glad the video was helpful.
Does the Safety Prime really save any effort or make things more efficient than just placing a primer in the arm by with your fingers?
@FatManLeather
5 ай бұрын
I think it saves quite a lot of time once it's set up well. I have the older setup, the new one may be different, just take the time to set it up and you shouldn't have to adjust it again, I recently loaded 2000 rounds of 9mm without an issue.
My press came with these primer attachments on the ram, but how do you attach them? I have no holes to pin them. It looks like you have a hole. I have the exact same press.
@FatManLeather
Жыл бұрын
The pin is in the ram, there should be a notch on the bottom of the primer arm that goes over the pin, basically gravity holds it in.
@Andy152R
Жыл бұрын
@@FatManLeather ok. Thanks for the video and reply!
Like!
@FatManLeather
4 жыл бұрын
Much appreciated.
I tried to return my LEE LOAD MASTER Press to Lee and they would not let me return it (only 4months old). This video is a turret press but I no long buy any Lee products. Buy once, very once
@FatManLeather
4 жыл бұрын
I've never had to return anything to Lee, I know they don't have the best warranty in the biz.