Lee Bulge Buster Kit / English version
Спорт
In this Video I Show you the Lee Bulge Buster for reloaders. With this Special tool you can remove the bulge at most cases which is caused by an gun with no fully supported chamber. Normaly you can not remove those bulges with your regular sizing die but with the Lee Bulge Buster it's easy to reload this ammo fired from such handguns.
Lee Bulge Buster, reloading, reloader, Shooting, wiederladertv, ammo
Пікірлер: 38
As all your videos they are very informative. Keep up the good work. Thank you
Think you for the info, I bought a balisti cast mark 2 and try to figure things out. Many thanx again brother loader
@wiederladerTv
10 жыл бұрын
No Problem brother
Another added benefit is that this process also trues up the side of the case head where dings from aggressive extractor claws, bouncing off rough concrete and being walked on, can cause issues.
great video!
@wiederladerTv
9 жыл бұрын
JBBooks4440 Thanks buddy.
Excellent video! As others have said, I did not even know about the lee kit! Thanks again!!!
@wiederladerTv
10 жыл бұрын
Your welcome brother; thank you very much for taking the time leaving a comment. Have a nice Weekend.
all ways have something good to offer thanks
@wiederladerTv
10 жыл бұрын
Thanks bro...your absolut right.
Been meaning to get one of these, but I keep forgetting!
@wiederladerTv
10 жыл бұрын
LOL, I know what you're talking about brother ;-)
Wonderful video using the Lee Bulge Buster Kit. I had discovered this subject several months back and this answered the question about the 'bulge' on some brass that I was reloading. Probably some range brass that I picked up to compensate for some that I couldn't retrieve from the range I would question why did you not slide the empty case over the plug so it is going backside first. This is the way the first video I watched showed how to use it. By doing it this way you don't have to hold onto the casing. For loaded ammo with the 'bulge' with a live primer you would have to be very careful. Primers are very sensitive. But thanks for the video. Well Done.
@wiederladerTv
9 жыл бұрын
Majeskty Thank you very much for leaving a comment buddy. I never tested to push the case through the die over the plug...
Don't forget to remove both the crimping sleeve and adjusting screw from the factory crimping die before installing the new guide sleeve.
@wiederladerTv
7 жыл бұрын
Yes, that right...you have to do so before.
perfekt wie immer ;-)
@wiederladerTv
10 жыл бұрын
Ganz lieben Dank...werde gleich rot im Gesicht. ;-)
I found that by rubbing fingers on a candle them rubbing the wax on the case they will glide right through . It dont take much at all .
@wiederladerTv
10 жыл бұрын
Sounds good...I'll give it a try. Thanks buddy
380 bulge buster also works very well to fix the rim of 223/556 cases! sometimes brass fired from machineguns or run through some reloading presses can squash the rim and make it out of spec.
@wiederladerTv
10 жыл бұрын
Thank you very much for the Information brother...did not know until now.
that's what a full length sizing die is for
@wiederladerTv
10 жыл бұрын
No, even with a full lenght sizing die you can't remove those bulge
What is the purpose of the factory crimp die? I always thought since the brass passed through the bulge buster that it would just screwed directly into the press and you would force the brass through it like a Lee lead bullet sizing die.
@wiederladerTv
10 жыл бұрын
The factory crimp die removes the bulge...die Bulge Buster is a way to catch the finished brass only. I start doing this opperation with the crimp die only the first time...it works but you have to catch flying brass ;-) With the Bulge Buster Kit it's a clean and easy way.
Great vid as always, I didn't even know about that die, a friend has a full auto MAC10 that bulges the brass real bad, we could reuse it instead of throwing it away now. Thanx a lot for the info, PS: what dimension do you resize your lead 45 bullets ?
@wiederladerTv
10 жыл бұрын
Thanks brother. My 45 bullets are sized to .452. Works best in my handguns (Glock 21 with IGB Barrel) and in the 1911 of my Buddy.
Nice video. Well thought out and constructed. Clean up your bench! You seem like a nice guy and we don't want you to have a loading accident... :)
@wiederladerTv
7 жыл бұрын
Your right.... my shop is cleaned now ;-)
Markus! Another "cool" tool!
@wiederladerTv
10 жыл бұрын
Thank you very much brother...hope your doing fine. Greetings Markus
whack! "like you can see here i don't need alot of force" whack, whack.... lol
@wiederladerTv
10 жыл бұрын
Hmm yes, you can here a Little bit but I don't have to muscle down the handle...a Little bit more than regular sizing but no big deal ;-)
@joehunt1980
9 жыл бұрын
It can be made a little easier by adjusting the die up till the ram just pushes the case through the sizing section of the die... Theres more leverage towards the end of the stroke of the press handle :-)
@wiederladerTv
9 жыл бұрын
Ok Buddy...thanks for the advice. Will do so next. Greetings Markus