No video
Led Strip Glow 220v
Warning ⚠️⚠️⚠️
dont try if you don't have knowledge.
#led #shorts
#education #electronics #electrical #experiment #engineering #diy #circuit #technology #science #creative #student #learning #arduino #project #viral #trending #foryou #fyp #insta #story #altium #utsource #jlcpcb #waypcb #abelectric #ideas #story
Пікірлер: 654
Very good job 👍❤❤❤
@Chrfilmer
8 ай бұрын
25V Kondensator an 220 Volt? Das ist gut? Bitte verkaufen Sie Ihr Internet.
@monarch73
8 ай бұрын
Das ist eine Schaltung aus der Hölle, die sich für Selbstmord geeignet. Vor solchen Inhalten müsste man eigentlich warnen
@simsalabim2101
7 ай бұрын
@@Chrfilmer 10 x 3,6V sind 36V am Elko. Das Ganze ist trotzdem lebensgefährlich, weil die spannungsführenden LEDs nicht ausreichend isoliert sind.
@krsfreak4283
7 ай бұрын
No it isnt, please dont do this, it works, but thath doesnt mean it works well or for long time
@monarch73
7 ай бұрын
@@krsfreak4283 Its aktually pretty hazardous. If the resistor is too weak, it can burn and set your house on fire plus the risk of getting zapped by touching the unprotected parts of the leds...
single diode rectifier, low power resistor and 25V capacitor quick guide how to set house on fire
@idiotwithasolderingiron
2 ай бұрын
With zombie light feature 😅
@LIBERPOBRECAPITALISTA
Ай бұрын
Más peligrosa q mi ex 😂
@igorsh5611
Ай бұрын
Воно вистрелить миттєво
@cinnamocinnamon
23 күн бұрын
Pretty dangerous if you live in an area with 240 V
@ShivakantRamTripathi
23 күн бұрын
Majk @@LIBERPOBRECAPITALISTA
This is extremely dangerous. Never do this💀🪦
@user-et6fu9dh6o
5 ай бұрын
sure
@Jatin7321
4 ай бұрын
The thing is that you don't have knowledge
@ChrisR2020
4 ай бұрын
Actually, it's not. The man put in the appropriate resistor to drop the amperage to an appropriate level for this circuit. It's only dangerous if you don't know what you're doing.
@patricklouie7737
4 ай бұрын
He puts a resistor with a high resistance in series with the phase, making this not dangerous. It's just as safe as either a bare 12 volt supply or less, like your battery on your car, because the voltage drop across the large resistor makes the voltage drop. Now, since these are small LEDs, I would assume they are between one to three volt LEDs, making that the potential between you and the ground. So no, this is not dangerous.
@MattFixesStuff
4 ай бұрын
ofcourse its dangerous. Anything you put in mains is not adviced. Yeah the circuit maybe safe (if the components can survive the occuring watts and dont burn). But the way its shown here its easy to short something out in the process making it incredibly unsafe.
Single diode Rectifier 👎 Full Bridge Rectifier 👍
@byGrumpy127
6 ай бұрын
@electroboom
@akbar0513
6 ай бұрын
😂😂😂
@gmalex123
6 ай бұрын
The capacitor evens out the current a bit and reduces flickering to some extent
@user-yu8kk5un5r
6 ай бұрын
@byGrumpy127
@netdedouga
5 ай бұрын
whats the roll for the resister?
⚡⚡⚡⚡Warning Warning Warning ⚡⚡⚡⚡ Never never ever do this dangerous stuff from this kind of videos 👎👎👎
I’m an electronic engineer, don’t do it at home, i’ll explain why. With the circuit in the figure, the diode is conducting for 1/4 * period of the AC wave, but it must provide high power to the capacitor in order to be able to keep the LEDs on for an entire period of the sine wave. Before doing these things you should check the maximum power the diode can withstand, besides all the power is dissipated on the single diode so it will fail sooner. Best case the diode will stop working without damaging anything, but it could happen that the high temperature of the diode could start a fire.
Опасно для жизни! Если через диод пойдет фаза то это поделка станет смертельно опасной!
@shamai1099
4 ай бұрын
Да вообще ужас, мало того что мерцает противно так ещё и крайне опасный фейерверк)
@ahG7na4
4 ай бұрын
основной трабл - что нет гальванической развязки (абсолютно каждый участок цепи имеет сетевое напряжение к земле, _независимо от полярности вилки)_ и резистор маленький по напряжению (1/4 Вт углепленочные до 100 В, что-ле) и по мощности
@shamai1099
4 ай бұрын
@@ahG7na4 ох меня как то шаразнуло так что еле еле чудом выжил, случайно коснулся краем ножа и упал из за чего это был мин но зараза было так больно. Поэтому всем советую по возможности по максимуму обезопасить
@djneon3703
4 ай бұрын
Да, может сильно ударить током
@shamai1099
4 ай бұрын
@@djneon3703 вероятнее всего может убить я бы даже сказал
Припаяй ещё сразу кнопку для вызова пожарных. 😂
Dangerous BS.
Bro just use a power supply
LED stripe should go into the transparent plastic tube, at least.
@jooproos6559
8 ай бұрын
Not needed!There are no contacts at the outside.
@simsalabim2101
7 ай бұрын
@@jooproos6559 What???
@geansantos9968
7 ай бұрын
@@jooproos6559 are you blind?
@thehemmo5078
7 ай бұрын
@@jooproos6559 there is clearly visib le 2 pads of contant with tin. if the leds break and its plugged it the contacts will charge to pontetially lethal voltage.
@user-fs5zq1ok4d
7 ай бұрын
Ну когда будешь себе делать, то в колбу засунь, а это пример просто что можно сделать или ты тупой и не понимаешь этого?
Bunun ustune seffaf plastik silindir ile korumaya alinablir.birde direnc arttirilirsa daha kullanisli hale gelir.birde sarjli pillede kesintisiz olur ve heryerde kullanilabilir.....
This is a no-brainer: a silly and dangerous LED strip. It is surely not advisable for amateur electronics hobbyists.
It doesnt go all the way off when he hits the switch. Thats not concerning at all.
@ardayldz2515
4 ай бұрын
its called a capacitor
Rectifier diode should be double
@666neoselen
4 ай бұрын
depends what you want as output. full bridge rectifier is useful to use positive parts AND negative parts of the pulse. he's using half the pulse, hence half the volts main power offers. usually power supply just take both pulse (to avoid bad balance in power consumption) then reduce them with a transformer, offering galvanic insulation. he don't, meaning anyone touching a metal part is potentially exposed to full main voltage.
@SaraJoseph-ek3mx
25 күн бұрын
Tuty😢😅ydgzy@@666neoselen
Burn burn burn
@jackcnx6000
8 ай бұрын
And Fire Fire Fire.
@user-nw7wv9td4z
7 ай бұрын
Or Runner Electronic Burner
@muezza2314
7 ай бұрын
BBQ
@djksfhakhaks
7 ай бұрын
With that unfused mess, maybe that is the state of his house.
@user-jb3cf3re4u
5 ай бұрын
Sond name Bhai
remember that approximately Ir=(230*radq(2)-2)/15000=22mA flows on the resistance inside the plug So the total power on it is: Ptot=0.22^2*15000=7W The resistor in the video allows at most 1/4W... about 10x less. Don't try the circuit if you don't want to burn everything! Plug included... You need a 10W resistor and not the one in the video!
@iggysixx
3 ай бұрын
Also; a polarized capacitor (max. 25V) plugged into 230V AC...
@Osiris_z6v
3 ай бұрын
@@iggysixxnot in 230v but after the rectifier and resistor otherwise it would pop in milliseconds
@iggysixx
3 ай бұрын
@@Osiris_z6v Is that thing with the switch (the white box that the plug is being plugged into) a rectifier? (Because otherwise, I'd say it's just partially rectified AC, and - more importantly - still too high of a voltage)
@Osiris_z6v
3 ай бұрын
@@iggysixx yes the black thing with a silver stripe is a rectifier diode
Лучше мост, мерцание намного меньше и в ленте около 100 светодиодов, чтобы как раз выпрямленного сетевого напряжения хватало
@DoppelgangerKiev
8 ай бұрын
И вместо резистора утюг что б не перегорал и тепло зря не рассеивалось.
@AnTrii7
7 ай бұрын
@@DoppelgangerKiev На 100 белых светодиодов в резисторе как раз нет необходимости. Разве что можно поставить предохранительный малого номинала - и то, он без конденсатора особо не нужен.
@Kuiperbelt-2
7 ай бұрын
А кто сказал что это светодиоды не 2,8 вольт,а не матрицы на другое напряжение?
@goldenarms1485
7 ай бұрын
Don't try at home😂
@user-xw1iq6is2f
7 ай бұрын
Лучше такое дерьмо вообще не делать
Only 12v DC
@UKRODIZIAK
6 ай бұрын
А, сколько по вашему, вольт приходит на контакты светодиодной ленты?
@henrylopez7117
6 ай бұрын
@@UKRODIZIAK 24 voltios. Por el capacitor
Не повторяйте. На ленте фаза смертельно опасно. И резистор 0.125 вт сгорит вместе с вашей квартирой. Собирал похожую поделку но надо всё надёжно изолировать и вместо резистора поставить конденсатор на 400вольт ёмкость расчитывается по формуле реактивного сопротивления.
@AtomiFox
4 ай бұрын
Не позорься. Учи мат часть. Выключатель с подсветкой тоже алярма?
@Norgame
4 ай бұрын
@@AtomiFox посчитай сколько нужно рассеять тепла несчастному резистору на 0.125вт
@Norgame
4 ай бұрын
Примерно 3 ватта уйдут в тепло смотря что за лента
@AtomiFox
4 ай бұрын
@@Norgame так я и не утверждаю что он долго продержится. Ну сгорит и сгорит. Для пожара этого недостаточно. Для работы достаточно поднять на порядок R и W в 0,5.
По хорошему нужно было бы диодный мост поставить
@anvarm2604
5 ай бұрын
Да. И размеры 1х1 см, и ток 1А.
@user-ph2fc5jb5j
5 ай бұрын
Пофигу мост, лучше защитным колпаком закрыть, а то при прикосновении к проводящим частям попадешь под напряжение.
@towele100
5 ай бұрын
@@user-ph2fc5jb5j а какое напряжение интересно будет непосредственно на контактах светодиов? Меня слегка дернуло от китайской 220V led лампы в форме "кукурузы". На ней нет никакого рассеивателя, тоже голые светодиоды, когда выкручивал лампу, видимо дотронулся до нескольких малюсеньких контактов. Был удивлен, потому что даже рука немного онемела.
@user-ph2fc5jb5j
5 ай бұрын
@@towele100 На каждом в отдельности светодиоде падение напряжения небольшое, от пары вольт до примерно десятка вольт. Но я имел ввиду, что в схеме нет гальванической развязки от сети (трансформатор или импульсный источник питания с трансформатором) из-за чего напряжение питающей сети целиком попадает на планку светодиодов.
100uf 25v rated capacitors is used for 230vac, the moment the switch turns on the capacitor will pop. A 400V rated capacitor is used at the rectified output of 325Vdc
@oztastics4977
4 ай бұрын
电阻是15kΩ
@Osiris_z6v
3 ай бұрын
The capacitor is put after the rectifier diode and resistor otherwise it wouldnt take more than a secondto pop
При таком подключении очень высокий коэффициент пульсации, полчаса с таким освещением и головная боль обеспечена + зрение сильно садится.
Hola cuántos led soporta 👍👍👍👍👍
To get 60 v from ac what is value of capacitor
Probador de corriente en toma corrientes 👏👌👍
manjinder❤❤❤❤❤❤❤❤❤❤😂🎉😢😮😅😊❤❤❤❤❤
Verygood job ❤❤❤❤
Puny half bridge rectifier
Me gusta la idea. pero que capacidad tiene
Que valores son de el capacitar el diodo y la resistencia
Нужен конденсатор побольше
Dont do that! 1. It's hot by power loss at R limit current. 2. Non isolated AC source. 3. It's aluminium pcb. Leaking current cause quite low impedance to ground
Membuat daya tahan lampu led lebih cepat panas dan terbakar
Будет мерцание заметно
You still screwed up because even with the resistor, it don’t turn all the way off which is why it’s still energized and why it flickers when powered on
Replacement of 15k resistance
@damca3160
6 ай бұрын
You can replace it with a slightly higher value rezistor or several lower value resistors connected in series (their total resistance must be 15k!). Or you can just use a small transformer.
@simoneazzoni3882
6 ай бұрын
Or you can avoid having such a device all together and not die or set your house or pets on fire
@ikilyou1b
6 ай бұрын
Or just use usb
Not only led strip glow your entire house glow too
REMEMBER !!! This is direct voltage... it's better to add a clear hose for safety... These comments are generated by AI, so please forgive if the grammar is a bit clumsy or doesn't fit.
Круто придумал
Was the capacitor necessary????? Stores energy if you turn off the LED strip it will continue working for a moment, it doesn't seem useful
What camera are you using?❤🎉
Retificador de diodo único não dá nem meia onda pra ficar melhor Ponte retificadora 👍
Пожароопасно, так как нет как минимум охлаждения светодиодов.
@MrBitlers
7 ай бұрын
Когда дойдет до пожара - владельцу уже будет всё равно, т.к нет гальванической развязки
@remonter_39
7 ай бұрын
@@MrBitlersя смеюсь с комментариев. Одного смущает, что нет охлаждения, второго что нет рассеивающего элемента, а факт того, что это нежизнеспомобно никого не смущает, и что светодиоды надо подписывать каждые 5метров....
@micheldodannah
7 ай бұрын
Led não esquenta
@user-dp8hu7cf3u
7 ай бұрын
Почему же нет. Диоды смонтированы на алюминиевой полосе, которая охлаждается окружающим воздухом.
@Ali_Haji_SouthAfrica
7 ай бұрын
These LEDs are not high intensity Diodes and have a These are in an SMD array. They don't pass a lot of current and each LED's Voltage requires approximately 3V
First of all there are more chances of some one getting zapped by 220volt ac mains... 😄 With simple single diode power supply there will a flicker in the LED light. Also the voltage rating of LED strip is not mentioned. Use of a proper dc supply ( x' mer based or smps ) will be more safe.🤔
❤❤
backround song name plz
does this work? Don't we need a step down transformer to lower the volts too?
Woow I can rely my life in this guy What kind I do it is this wat he is doing is he 8snt not power main supply instead giving 12 v supply to it
Leds strip kitne volts ki hai??
Of course the zener diode was not usefull, you can replace the 15K resistor by 220nF X2 capacitor and get better yield
very good
Where to get lead strip
Don't think about it, it's DANGEROUS.
Blink kesa hoga
Una tira Led conectada a la red eléctrica pública, un capacitor de 25 voltios y conectados directamente no explotó
Operating voltage is 110v / 230v ?
Attention les leds ne sont pas isolé du secteur
Thank you
Resistor will fry, and capacitor pop.
You put energy into and something which is light... Where does the light or energy go after it has been used? It has to go somewhere it just can't go back into nothing
Very safe solution. :-)))
Lots of people shouting danger 😂😂😂 Little they now that basically that's how r made their lights for 🎄 😂😂😂😂😂
Mucho voltaje para tan poca cosa
No dan tiempo suficiente para ver los detalles escritos. There is not time enough to read the written details
لا تنسى الحرارة التي تنتج عن المقاومة فهي قد تذيب كل الدائرة ههههه
Technology of Asia....
@UKRODIZIAK
6 ай бұрын
Ты когда-то разбирал устройство от комаров, которое вставляется в розетку и нагревает пластинку запах которой отпугивает комаров?
The resistor will burn quickly.
4w in the resistor 0,1w in the led strip the dumbest way to drive leds
Упаси госпдь того, кто решится это сделать....
Indian is the best, and the bravest.
Эти приборы ослепляют даже через экран
А в Резекне 36 в😂😂😂😂😂 при 220 без защиты конденсатор заделает фиерверк для пожарных
Я юбител таких и иных изобритеней
@Norgame
4 ай бұрын
Главное не повторять. Резистор на 0,125 вт сгорит очень быстро. И на ленте присутствует фаза смертельно опасная поделка.
خیلی سریع است
@mithunali7781
4 ай бұрын
Rraandd😢😢😮😮😮
It is dangerous for your life! No isolation with the live wire.
Capiciter and registance ❤❤ going their work
Amigos, alguien me puede decir que valores se necesitan en esos 3 componentes, pero para que esto funcione en 110v, me refiero al: Capacitor, Resistencia, y el diodo (creo que serían esos 3)
Amazon sells it for cheap . so very basic led.
After killing the resistor this thing kills you
blinking LED = Half wave rectifier
❤❤❤❤ super 👍👍🙏
Гальваническая развязка? Электробезопасность? Не, не слышал)
Thank you Ab 😊
Amazing
كيف تستعمل طاقة 220Vفمثل ذي الاجهزة 🤨شكلك تبينا نهلك مو نتعلم💢
Hay đấy bạn 🎉🎉🎉
Is it work 22watt led strip
If this explores i will come to your house
🎉🎉🎉🎉
Bahut sundar😢
Donot touch the led 😂
এই লাইট অনেক দিন থেকে খোজছি লাইটার নাম কি দাম কতো
Para alimentarlo con 127 volts de AC?
Das sowas überhaupt hochgeladen werden kann, Reparatur Tips bei KZread waren schon immer fragwürdig.
Skemanya mana ya
❤❤❤❤
Bahut badhiya 🎉🎉😢🎉🎉🎉
MARUF❤
@EusobAli-zm6lz
Ай бұрын
maruf
Semplice modo per far saltare il salvavita/contatore di casa 😏