Note after adding the hoses and sand to the pump DONT turn on the pump yet FIRST you got to backwash until the water runs clear turn off the pump and then switch it to rinse and turn it on and run it till it turns clear turn it off again and then switch it to filter mode and then turn it back on. Backwash is necessary when applying new sand or when pump pressure is at 15 and you should be fine :) hope this helped anyone

@chanelpartlow

3 жыл бұрын

I am running my filter for the first time today. What you are saying is change the setting to backwash until the water is clear then rinse it and then filter? Just want to confirm I'm doing this all correctly.

@kennypr

2 жыл бұрын

Winter mode what’s the use of that mode ?

@deanmartinez5153

Жыл бұрын

Thanks for the tip

Great video! I assembled the pump using only this video and have zero leaks. Thank you for being very thorough and explain every step in detail! Take care and God bless

I installed this 50d to our Coleman 18X48 pool yesterday. Thanks for this step by step video. I have no leaks from the hoses or ports so far. Maybe some seepage at the drain plug at the bottom of the tank, but not enough to be concerned. I had a heavy leak at the see thru cap at the leaf trap, but kept cranking until it was tight enough. It stopped leaking at that point. I did purchase a back wash hose when I bought the pump. I am so glad I did! I backwashed and rinsed before filtering. That would be the only instruction missing in this video. The pressure gauge was reading 5psi when I first started filtering. I ran the pump all day, and the pressure reached almost 10 psi by the end of the day. The water was some murky when I installed the pump, but the water cleared significantly after a few hours of running the filter. I’m planning to run the pump all day today, and back wash again this evening. My skimmer basket is working better with the addition of this pump. The pump is super quiet, and moves the water well. Thank you.

@katricejohnson4257

2 жыл бұрын

Hello I just installed ours with same pool you have did you remove the filter things inside the pool?

Nice, but you did not show that you should backwash and rinse before you set your pump to filter mode.

@brentad2004

Жыл бұрын

Yeah, got a cloud "dust" in my pool, thanks! lol

One of the best installation pump video on KZread, thank you so much

Explained extremely well.only needed this video not the .Manual for set up..THANK YOU 😎👍👍

Great Video. What wasn't in the Instruction Manual.....You Cleared up for me thank you so much for making this video.

pump sat in my patio for four days till i come across this how to vedio ....thank you very for your help !!!

@carlosmaldonado2313

4 жыл бұрын

No problem bud

Thank you for the video one of the best videos

Thank you so much I just installed this sand filter on the same exact pool lol

Excellent job. Thank you very much. 🙂

This was the best video ever thank you big thumbs up

Thanks for a great video!

Watch this video before you install! So many helpful tips and visual instructions. I wish this was linked on the instruction manual.

@justinsupersoniczeanimator6662

2 жыл бұрын

Does it have a recirculation?

Excellent job

Good craftsmanship

Thanks brotha, much needed

Good Video, Very Informative. The only thing I see in the Video that I don't like about the pump is the Power Cord is really short. You would think the designers would have given a longer and better power cord. Other than that everything looks great. Thanks for the video.

This video has helped

Thank you same pool

Hey what did you use to hang your hoses?

Thank you su much inwas so extres about,I buy the same pump and it took me like 3 hours to put it together and then I was liking lol.and I see your video man so easy..🙏🙌💫

Thank you

Very helpful video! Any idea what to do if it’s leaking from the drain plug? HELP!

Just got this unit today and only complaint i have so far is no On/Off switch. I did see in the manual it says to backwash then rinse beforehand. In this video you went straight to filter and running the pump. I'm curious as to why? This is a great video for setup don't get me wrong I just want to make sure I get the longest life possible from it. Thank you.

How can I get replacement o-rings and gaskets for the 35d? I need a pump plug as well. I live in Phoenix...I see you guys are in Scottsdale.

My Dads gf got one from her friend and had me set it up. She didn’t have the manual so here I am

Thanks

So it's been a year or so. What do you think of this system long term? I'm looking for sand filter recommendations

Thanks for sharing video. Which wording do I start the filter on?

Can I use this for a 15x33 easy up pool? If so what adapters do I need for the hoses?

I have this same pump. Are the valves automatically open? I read on another pump you must open valves by pressing lever and turning clockwise till it stops. Is this one the same?

How did you set this up using the hoses I just brought a 18x48 pool I have a intex saltwater system but don’t know how to add it to my Hayward Pro Series Sand Filter System, 18 in Filter with 1.5 HP Matrix Pump

I have the same pool,i need this filter/pump how does it do long term,and also could you do a video of how to vacuum pool with this pump???

having issue with sediment in pool even after back washing for 10mins. stil have very fine silt entering pool and collecting on bottom after several hours of runnung.

Do you have to lubricate all of the gaskets and O-rings?

Hello I just got the pool I need help finding the parts for the pool and the size of the hoses can you plzz help me

Thank you for the concise walkthrough. Cheers Given that a new bag of sand was just added, will I get a big blast of murky water into the pool if I first set the selector to Filtration and turned the water pump on as suggested? I feel like I would need a Rinse of the sand first.?. FWIW, I was actually anticipating to see that process in this video. I went back to make sure that I didn't miss it.

@sandrastevens2598

5 жыл бұрын

GAME Manufacturer recommends that you clean and prepare the new sand that is in the sand chamber first (prior to filtration). Cleaning the sand prior to filtering your pool will remove most of the dust and tiny sand particles that may exist in the sand. If you move straight to filtering, these particles may end up in your pool. sls@game-group.com

@fishinfeen6194

5 жыл бұрын

@@sandrastevens2598 im sure i can figure out how to clean sand..but is there a way that technicians clean filter sand that someone like me may not know about

What about square hole on the pool that would be used for Filtration

Weve been having trouble with the drain part on big base. About 2:10 that piece. It keeps losing water. Weve taken it all apart. At 1st was to loose & I had washer in cap. Then we put cap on to tight & loosened the whole thing. Weve watched the video about 20 times & doing the washers & everything right. Maybe just need to put cap on loose? Cant have it slowly drip out all summer it's on a pallet on grass would have mud. Any ideas or help?

That looks like a direct replacement for the cartridge pump on the Coleman pools. Is that correct?

Help, i just purchased this and when i put the 4-way value in it does not sit flush on top. Some of it does on one side but the other shows the o ring.

What are those connectors called for the hoses intake and outtake?

I wanted to know I got a Coleman pool I wanna install a sand filter and I bought but the fittings are different I have that same pool on ur video what can I do

Is this pump good for 58x18 pool? If not which pump should I get?

Is the 35d big enough for the 18x48 pool

Where do you set your switch or turn handles when vacuuming and do you leave the outflow open or close when vacuuming. No videos on you tube for this pump on how to vacuum your pool and what to do on your pump..any help would be appreciated

What size is that threaded connector?

I need a replacement flange for the 50d and i cant find it anywhere??!!! Just haywards!!

Any idea why I can’t get the clamp on? It doesn’t fit w the O ring, it’s like there’s a gap. It’s also a new sand filter

Can I use the same pump in order to pump water to a sand filter

Do we have to use the tape?

Is this pump water proof? I don’t see any body talking about that but obviously is going to be getting splash on it since is sitting right next to the pool and is always outdoor.

Weee do i hook up vacuum

how and where do we set up the vacuum?

Where did you buy it and how much was it?

Everything has gaskets origs Teflon and adapters

What’s the measurements of the adapter or size?

Where can i get the gaskets and those fittings i have the same pool. I didnt get any of the fittings or gaskets

@1984Alive

4 жыл бұрын

Video is worthless without specifics on hoses, adapters. Stressing!!!!

hi soo im a bit confused with my pool. Its actually the exact same pool as yours. so my question is, should my pump have a suction or blow out bubbles through the left side of the pump. side A. should side A be bubbly or no bubble but strong suction??😩🤷‍♀️ please help..

@gamegroupproducts

4 жыл бұрын

Please contact our customer support team at products@game-group.com and they will be able to better assist you.

What is the hp of the pump

is it the exact same setup process for the sandpro 75D???

@ericw7381

4 жыл бұрын

The manual also says to do this too! Speaking from experience, there is dirt to sweep up if you don't.

Question for the sand I can't use any sand or is a specific sand for the tank

@randymiller7659

5 жыл бұрын

polyester media balls are better than sand,sand filters to 40 micron while polyester media balls filter to 3 micron

@ 11:08 you installed the pressure Gauge without teflon tape!!!!!!!!!!!!! 🤪 🤪 🤪 🤪 🤪

It is on the 4 way pipe thing.

@sandrastevens2598

5 жыл бұрын

Please contact GAME customer service or email us a pictures of the product mentioned. Customer Service Department 888-339-2546 Ex. 135, products@game-group.com

What should my pressure gauge read... I’m running about 5 pounds on gauge ??

why is there even a hole in the bottom of the tank? that plug doesnt even drain !

you need to back wash before filtering

Where do I buy the conector for threaded pipes ?

@pfarris318

4 жыл бұрын

I used my original from the SandPro box mixed with 1 or 2 from original pool.

Good idea to back wash the new sand before filter. What is the price of these?

@chrisdedios492

4 жыл бұрын

I just bought one from Dohenys in Wisconsin, had it shipped for free to California, for $179, just installed it today

@johnwiechel

4 жыл бұрын

@@chrisdedios492 wow that was cheap.

@chrisdedios492

4 жыл бұрын

@@johnwiechel bought it last Thursday, maybe they still have some in stock

I forgot to clean my sand first in my Game 50D and it spit sand or dirty water into my pool for a second and then ran clean. How long will it take to clean that mess out of my 4000 gallon pool? Recommendations on cleaning it up? Other than that its running great and I followed all instructions and have no leaks. Thanks in advance.

@subswithnovidChallenge-ct1zr

5 жыл бұрын

DigitalDawn Note after adding the hoses and sand to the pump DONT turn on the pump yet FIRST you got to backwash until the water runs clear turn off the pump and then switch it to rinse and turn it on and run it till it turns clear turn it off again and then switch it to filter mode and then turn it back on. Backwash is necessary when applying new sand or when pump pressure is at 15 and you should be fine :) hope this helped anyone

@subswithnovidChallenge-ct1zr

5 жыл бұрын

Also try running the pump to see if it’ll pick up and suck all the sand back into the pump

My drain plug does not fit in hole. The hole is too small.

Shouldn't the sand be flushed before filtration to the pool?

@sandrastevens2598

5 жыл бұрын

GAME Manufacturer recommends that you clean and prepare the new sand that is in the sand chamber first (prior to filtration). Cleaning the sand prior to filtering your pool will remove most of the dust and tiny sand particles that may exist in the sand. If you move straight to filtering, these particles may end up in your pool. sls@game-group.com

@NaldyPR10

5 жыл бұрын

yes

@oscarc2286

5 жыл бұрын

how do you clean the sand and prepare before you put in? thanks

@subswithnovidChallenge-ct1zr

5 жыл бұрын

Oscar C put in backwash mode and then rinse until water runs clear and then put it in filter mode

Where can I purchase parts for this pump?

@TheSexyty11

3 жыл бұрын

This the answer i came for

If it has a o ring you don't need the tape.

@barrycowan1997

3 жыл бұрын

That’s what I thought. Brass into plastic should be fine too shouldn’t it

I have extra parts left is that normal

One side is tighter than the other. Please help.

@sandrastevens2598

5 жыл бұрын

Please contact GAME customer service or email us a pictures of the product mentioned. Customer Service Department 888-339-2546 Ex. 135, products@game-group.com

I bought this pump and filter… and i never was able to use. On day one I setup and ran the cycles (backwash etc) and the next day the pump tripped my GFI breaker. I have been back and forth with their customer product team via email. They don’t want to replace my pump because if it trips my GFI it’s my GFI. I have tried ALL in my house and even in my friends house. What more do they need. They have no interest in standing behind their product. If you call, all warranty is through email. I am disappointed to say the least.

Yeah my plug leaks so bad lol

Why is my pressure not even going to 1

You should have backwashed and rinsed your sand before you started filtration

Oh and no teflon with an oring

Hold on - so you took generic pump shipped from china and rename it to your own company name ? Hahaha