Nice video 2 questions... do you reuse the foam and paper? where did you find the green stacked drawers on the floor?
@metaldesignzcanada
4 жыл бұрын
I refuse the paper if it isnt crushed. I use new foam every roll.. it's super cheap and helps the metal take a deep impression! The drawers are IKEA!
@lynne7741
4 жыл бұрын
@@metaldesignzcanada Thank you
@palepa032 жыл бұрын
What is your cutter called?
@metaldesignzcanada
2 жыл бұрын
The Cutter at the beginning of the video is called a Guillotine Shear - It's made by Pepetools. It's a great tool but it's really expensive. I also have a couple of bench shears that are around $100... they curl the metal when they cut, but it's easy enough to flatten!
@phoxhaus56863 жыл бұрын
What type of laser printer would I need for this? Would a Cricut work? :) And do you use card stock, for deeper impressions? I assume you’re selling this? Thank you.
@shelleyhubbs3563
3 жыл бұрын
Yes we sell our laser paper at www.metaldesignz.com We use a C02 laser to cut the paper. Cricuts are a PAIN to pick out all the little bits and pieces... Thanks!
@phoxhaus5686
3 жыл бұрын
Shelley Hubbs Thank you. I just want to cut out names... nothing too fancy, lol.
It's hard to measure... the calipers squish it but it's a couple mm thick. I get it from a bead wholesaler... and offer it on our website. It's better than the foam I tried from hobby lobby or Michaels or amazon. Its inexpensive and help the paper work better!!
@dennydiamond8597
4 жыл бұрын
Metal Designz Thanks, Shelley. I’ll be ordering through the website. Hope all is well, Denny.
@metaldesignzcanada
4 жыл бұрын
@@dennydiamond8597 things are excellent! Super busy but busy is good :)
Пікірлер: 13
Nice video 2 questions... do you reuse the foam and paper? where did you find the green stacked drawers on the floor?
@metaldesignzcanada
4 жыл бұрын
I refuse the paper if it isnt crushed. I use new foam every roll.. it's super cheap and helps the metal take a deep impression! The drawers are IKEA!
@lynne7741
4 жыл бұрын
@@metaldesignzcanada Thank you
What is your cutter called?
@metaldesignzcanada
2 жыл бұрын
The Cutter at the beginning of the video is called a Guillotine Shear - It's made by Pepetools. It's a great tool but it's really expensive. I also have a couple of bench shears that are around $100... they curl the metal when they cut, but it's easy enough to flatten!
What type of laser printer would I need for this? Would a Cricut work? :) And do you use card stock, for deeper impressions? I assume you’re selling this? Thank you.
@shelleyhubbs3563
3 жыл бұрын
Yes we sell our laser paper at www.metaldesignz.com We use a C02 laser to cut the paper. Cricuts are a PAIN to pick out all the little bits and pieces... Thanks!
@phoxhaus5686
3 жыл бұрын
Shelley Hubbs Thank you. I just want to cut out names... nothing too fancy, lol.
What is this kind of foam? How thick is it?
@metaldesignzcanada
4 жыл бұрын
www.metaldesignz.com/foam-backing-material-get-better-impressions-and-fun-colours/
@metaldesignzcanada
4 жыл бұрын
It's hard to measure... the calipers squish it but it's a couple mm thick. I get it from a bead wholesaler... and offer it on our website. It's better than the foam I tried from hobby lobby or Michaels or amazon. Its inexpensive and help the paper work better!!
@dennydiamond8597
4 жыл бұрын
Metal Designz Thanks, Shelley. I’ll be ordering through the website. Hope all is well, Denny.
@metaldesignzcanada
4 жыл бұрын
@@dennydiamond8597 things are excellent! Super busy but busy is good :)