it is possible to reduce the spacer height to get a tighter fit against the roof?
@Cryptocaryon3 жыл бұрын
Do you need to install the cross bar directly over the sunroof? Can you omit that one without impacting the integrity of the rack?
@PrinsuRacks
3 жыл бұрын
Yes, you should be able to leave that cross bar out and not compromise any of the integrity of the rack.
@rathman46013 жыл бұрын
I believe that LC 100 series have some interchangeable parts with the 1st Gen Toyota Sequoia. Would that fit a 1st Gen Toyota Sequoia?
@nathanwright1031
3 жыл бұрын
That is a great point but we have not had a chance to verify that ourselves. You could always give it a try!
@rns22226 ай бұрын
What lb/ft of torque are you tightening the bolts down at?
@robertalbino35024 жыл бұрын
What do you do if your factory roof rack only has 4 mounting points?
@ousooner1506
4 жыл бұрын
Remove the weather stripping to reveal the correct bolt positions on LX470.
@abboudabudafair14843 жыл бұрын
Well done... but how strong is it?!... i mean; Can it hold heavy loads e.g of an additional spare tire for off-road travels i.e on an African environment or so?!
@nathanwright1031
3 жыл бұрын
Yes it can hold heavy loads. A tire along with all kinds of other gear would be fine. Roof top tents, etc. The week link with our roof racks is actually the structure of the vehicle roof and not the rack. That is what limits load capacity. All of that considered you still want to be careful to not add too much weight up high like that and it is important to evenly disperse the weight depending on what type of off-road driving you will be doing.
@deanharris22403 жыл бұрын
Hi, I'm looking to install Prinsu rack on a Chevy Suburban. Don't see a vid on that just a pdf and the pdf shows drilling holes. Wondering why we can't use hex bolts like in this video??
@PrinsuRacks
3 жыл бұрын
We do not currently make anything for the suburban but you are welcome to check back in the future.
@nwilson2283 жыл бұрын
What is the dynamic and static weight ratings on these?
@PrinsuRacks
3 жыл бұрын
About 600 LBS static weight and about 300 LBS dynamic weight.
@jano350z4 жыл бұрын
Do you guys have a install on A 1st gen Tacoma ?
@CBIOFFROADFAB
4 жыл бұрын
we do not have an install video on a 1st gen Tacoma at this time but we hope to add that one. In the meantime if you need any help at all with an installation please give us a call!
@OBHector3 жыл бұрын
What kind of silicone did you used?
@CBIOFFROADFAB
3 жыл бұрын
We use type 270 Black RTV silicone on our installs.
@LuanNguyen-rj1bt Жыл бұрын
I have a lx470 which is the the same as the landcruiser. Do I reinstall my weather stripping. I had a prinsu on my old tacoma and had to reinstall the westherstip.
@PrinsuRacks
Жыл бұрын
Hey there! Yes, we do recommend reinstalling the weather stripping after you have finished the installation. If you have any other questions you can reach out to our customer service representatives via email at Info@cbioffroadfab.com.
@LuanNguyen-rj1bt
Жыл бұрын
Okay, I just didnt see you guys put it back on in the video. What did you guys use to make it seal back up
@PrinsuRacks
Жыл бұрын
@@LuanNguyen-rj1bt We recomend cleaning the area very well and using your choice of adhesive or double-sided tape.
@LuanNguyen-rj1bt
Жыл бұрын
The 3:15 mark on the video is what I'm referring too
@alexmroz93164 жыл бұрын
Would this rack work for the LX470?
@PrinsuRacks
4 жыл бұрын
Sorry we have not tested this product with the LX470 and cannot guarantee fitment. Thanks for reaching out!
@CrazyforCruiser
4 жыл бұрын
Of course it will, Land Cruiser 100 and LX470 are the same.
@ousooner1506
4 жыл бұрын
Yes. Just remove the weather stripping. It will reveal the correct bolt positions.
@Lost1st4 жыл бұрын
It’s funny how these guys don’t clean the area before putting silicone down🤦🏻♂️
@khm78003 жыл бұрын
Hi, does it fit on fzj105?
@PrinsuRacks
3 жыл бұрын
Our roof racks are made vehicle specific and we have not test fitted so we can not say if it would or not.
Пікірлер: 35
Thank you!
Well done... Thanks
it is possible to reduce the spacer height to get a tighter fit against the roof?
Do you need to install the cross bar directly over the sunroof? Can you omit that one without impacting the integrity of the rack?
@PrinsuRacks
3 жыл бұрын
Yes, you should be able to leave that cross bar out and not compromise any of the integrity of the rack.
I believe that LC 100 series have some interchangeable parts with the 1st Gen Toyota Sequoia. Would that fit a 1st Gen Toyota Sequoia?
@nathanwright1031
3 жыл бұрын
That is a great point but we have not had a chance to verify that ourselves. You could always give it a try!
What lb/ft of torque are you tightening the bolts down at?
What do you do if your factory roof rack only has 4 mounting points?
@ousooner1506
4 жыл бұрын
Remove the weather stripping to reveal the correct bolt positions on LX470.
Well done... but how strong is it?!... i mean; Can it hold heavy loads e.g of an additional spare tire for off-road travels i.e on an African environment or so?!
@nathanwright1031
3 жыл бұрын
Yes it can hold heavy loads. A tire along with all kinds of other gear would be fine. Roof top tents, etc. The week link with our roof racks is actually the structure of the vehicle roof and not the rack. That is what limits load capacity. All of that considered you still want to be careful to not add too much weight up high like that and it is important to evenly disperse the weight depending on what type of off-road driving you will be doing.
Hi, I'm looking to install Prinsu rack on a Chevy Suburban. Don't see a vid on that just a pdf and the pdf shows drilling holes. Wondering why we can't use hex bolts like in this video??
@PrinsuRacks
3 жыл бұрын
We do not currently make anything for the suburban but you are welcome to check back in the future.
What is the dynamic and static weight ratings on these?
@PrinsuRacks
3 жыл бұрын
About 600 LBS static weight and about 300 LBS dynamic weight.
Do you guys have a install on A 1st gen Tacoma ?
@CBIOFFROADFAB
4 жыл бұрын
we do not have an install video on a 1st gen Tacoma at this time but we hope to add that one. In the meantime if you need any help at all with an installation please give us a call!
What kind of silicone did you used?
@CBIOFFROADFAB
3 жыл бұрын
We use type 270 Black RTV silicone on our installs.
I have a lx470 which is the the same as the landcruiser. Do I reinstall my weather stripping. I had a prinsu on my old tacoma and had to reinstall the westherstip.
@PrinsuRacks
Жыл бұрын
Hey there! Yes, we do recommend reinstalling the weather stripping after you have finished the installation. If you have any other questions you can reach out to our customer service representatives via email at Info@cbioffroadfab.com.
@LuanNguyen-rj1bt
Жыл бұрын
Okay, I just didnt see you guys put it back on in the video. What did you guys use to make it seal back up
@PrinsuRacks
Жыл бұрын
@@LuanNguyen-rj1bt We recomend cleaning the area very well and using your choice of adhesive or double-sided tape.
@LuanNguyen-rj1bt
Жыл бұрын
The 3:15 mark on the video is what I'm referring too
Would this rack work for the LX470?
@PrinsuRacks
4 жыл бұрын
Sorry we have not tested this product with the LX470 and cannot guarantee fitment. Thanks for reaching out!
@CrazyforCruiser
4 жыл бұрын
Of course it will, Land Cruiser 100 and LX470 are the same.
@ousooner1506
4 жыл бұрын
Yes. Just remove the weather stripping. It will reveal the correct bolt positions.
It’s funny how these guys don’t clean the area before putting silicone down🤦🏻♂️
Hi, does it fit on fzj105?
@PrinsuRacks
3 жыл бұрын
Our roof racks are made vehicle specific and we have not test fitted so we can not say if it would or not.
What size tires are on that cruiser?
@aaron0707
4 жыл бұрын
They are 285/75/17 so 34x11.50
Part #please