كيفية حل عطل Xerox 010-723 بطريقة سهلة جداً مجاناً بدون فك أو تركيب و حل مشكلة التصوير و الطباعة
error 01
xerox fuser error
copy
black copy
err 01
xerox fuser
xerox paper jam
error C1
what is code f 01
error 32
code c1
open heat error xerox
white copy
fuser unit
c 32 01
copy of manual
010 327
code 32
paper feed switch
e 010
Skip to main content
Search
Printers
Printer Supplies
Scanners
Shop Online
Featured Software
Office Printing Solutions
Industry
Business Services
Production Print Solutions
Small and Medium Business Solutions
IT Services
3D Printing
Solutions Innovation
Insights
All Support and Drivers
MySupport
Support Community Forum
Contact Us
Sell Xerox products and services:
Log in to your partner portal:
Buy products and services:
Become a partner
Xerox Financial Services
Account
Solution : Power the Machine OFF and ON CAUTION: Wait at least 30 seconds between powering the machine OFF and powering the machine ON. Damage to the optional hard disk could occur.
Press the power switch to the OFF (O) position.
NOTE: If the machine is equipped with the optional hard disk, the machine remains on for approximately 10 seconds, while storing files and preparing for shutdown. The machine then shuts down completely.
Press the power switch to the ON position.
IF THAT FAILS TRY THIS NEXT:
Solution : Clear the Paper Jam Behind Cover A
Open Paper Tray 5 (Bypass Tray).
Lift up the Cover A release lever, and open Cover A.
Remove any paper below the Fuser Unit by carefully pulling up and out.
WARNING: Do not touch the Fuser Unit, as it may be hot.
If the jammed paper is inside the Fuser Unit, lower the green A2 lever in the direction of the arrow to open the Fuser Unit Cover.
Push down and rotate the green A1 lever in the direction of the arrow to feed the paper from the top of the Fuser Unit.
NOTE: Do not pull paper downward during removal.
Close Cover A until the cover latches.
Close Paper Tray 5.
Log In
Shop
United States(en)
Fault Code 010-327: Fuser On Time Failure
Article Id: 1777175.html | Published: 12/06/2018
Product support for
WorkCentre™ 5222
WorkCentre™ 5225/5230
WC5225A_WC5230A
Try these solutions
Remove Any Jammed or Torn Pieces of Paper and Other Obstructions From the Paper Path
Remove and Reinsert (Reseat) the Fuser Unit
This Problem Requires Additional Assistance. Contact Support
Did this help?
YES NOT YET
About Xerox: Corporate Information
Ways to Buy
Support and Drivers
Contact Us Careers Investors Privacy Legal Cookie Preferences Site Map
© 1986 - 2021 Xerox Corporation. All rights reserved. Xerox® is a trademark of Xerox Corporation in the United States and/or other countries.
By using the Xerox site, you agree with our use of cookies. Want to know more?I consent to cookies
,
These are the possible codes and the reason for occurence of this code in your copier
010-150, 155 -Too much or not enough paper in duplex tray
010-300 -Fuser thermistor, 010-302 --Low fuser temperature , 010-304- Bad fuser temp, 010-308 -High fuser temperature or open thermistor, 010-310 --High fuser temperature , 010-312 --Fuser not up to temperature after energy save, 010-314 --Fuser problem , 010-320 --Fuser web finished , 010-330,327, 335, 340- Exit switch, vertical sensor switch actuated when power is turned on
010-150, 155 Too much or not enough paper in duplex tray 10-300 Fuser thermistor 10-302 Low fuser temperature 010-304 Bad fuser temp 10-308 High fuser temperature or open thermistor 010-310 High fuser temperature 010-312 Fuser not up to temperature after energy save 010-314 Fuser problem 010-320 Fuser web finished 010-330,327 335, 340 Exit switch, vertical sensor switch actuated when power is turned on
This is a fuser error, so we'd start by replacing that. The fuser PN is 126K16480.
This particular error code may be a false error, in which case either the Power Unit 105E11370 or the MCU Board 960K09910 might be bad.