www.amazon.com/gp/product/B008TSV6VW GENUINE OEM KOHLER PARTS - KIT, VALVE COVER 20 096 14-S

@xxxCawsomenessxxx

6 жыл бұрын

Where do I find the bolts for the valves

@mygiguser

6 жыл бұрын

Where do you see bolts on the valves? Not sure what bolts you are talking about.

@xxxCawsomenessxxx

6 жыл бұрын

mygiguser damn it I don't what it's called the things that bolt on the things that pushes the spring

@kellonpitts2650

5 жыл бұрын

@@xxxCawsomenessxxx rocker arms

So much easier to learn this way. Rather than trying to learn from a manual. Thanks.

Very nicely done, thank you! Lighting and focus are outstanding, and your directions are clear and to the point. I wasn't sure I wanted to tackle a DIY valve adjustment but with this video, I'm pretty sure I can get it done.

I'm fixing to do my valves in my 18.5 HP Kohler Courage on my Gravely 1640 ZTR. This video made it easy to understand.

I would like to thank you for the detailed info given in this video. It was extremely helpful.

Well done video and easy to understand the calm speaker. I now have the confidence to fix the valve cover leak and adjust valves. Thank you!

@FEEDbigJAKE

6 жыл бұрын

Nice

Thanks for video. I did a gasket replacement and valve adjustment. The adjustment of the valve lash locking nut and screw was the opposite of what I’m used too. Had a hard time getting my head around it because of the valve lash adjustments during my Volkswagen days.

Great video and straight to the point. I didn't know they had made an aftermarket piece to keep the valve cover from dripping, oil. I ended up fabricating a piece of metal on my kohler cause the dripping on the exhaust was driving my nuts. Thanks

Thank you for taking the time to make this video. You answered all my questions about the procedure and settings for valve adjustment on this engine.

Well done video. A trick for people to find the correct crank position is turn the flywheel until both rockers are loose. Take out the plug and run a piece of coat hanger wire in against the piston to find bottom dead center. Easy.

Thanks mygiguser for taking the time to record and post the valuable information.

You are a very talented and thoughtful mechanic - been working on small engines for years and years, but I learned something today. Great accent by the way! Thanks!

@mygiguser

4 жыл бұрын

Robert Jacoby 🙏 thank you!

Thank you for this video! My mower is running again! I noticed on my mower that the stud that holds the rocker arm had loosened out of the block on the exhaust side!! So I had to tighten that back in first, then make the adjustments. Check those studs also! Thanks again, great video.

Great video! Good info and clearly explained. I especially liked the slow motion sound at the end to hear the smooth running motor. Great job!

@mygiguser

4 жыл бұрын

Thank you!

Great video and good explanations. Thank you for your time. Very helpful.

Thank you ! Well done clear and concise

Good Video: clear, steady well explained

Great video. Side note, check to make sure both springs are coming out the same lenght as you turn the flywheel. The valve seat came out on mine and left the valve stuck open.

Well done video and informative. Thank you very much.

Fantastic video. Thanks for your help.

I know how to set valve lash but I still enjoyed your video and learned a few tidbits. Thanks!

Thanks for this info! REALLY!!! I Had my engine start back fireing and 1 minute later it stopped running. Itried to restart it with a battery charger on start. The engine acted like the compression was being blocked all the sudden. At 1st I thought the battery, then I thought the starter, then fuel blockage, so I pulled the spark plug and the starter spun faster than before. Then I found out the valves may need adjustment so I Adjusted them. Still had engine kick back. So I found this KZread video an found the exhaust valve rod guide was pushed out of hole to far as you suggested and pushed it back in and readjusted the valves and it started. Thanks for this video info it saved me 5,000 $ as Istarted looking for a new mower today but thought I would try 1 more time. Thanks for the info!

@bjacker7019

4 жыл бұрын

WHAT? i didnt hear any reference to guides? and dont understand what you mean by out of hole too far?

@tylerharless4048

3 жыл бұрын

He is stating an issue he found with his and the valve guide is what the stem of the valve rises on inside the cylinder head they can loosen overtime especially if the engine runs too hot from dirty cooling fins.

Very much appreciate this video! My engine was spewing gas out of the carb bc the valve was too tight. You saved my life - thanks! :)

@mygiguser

2 жыл бұрын

you welcome!

many thanks, great video, very well explained

It worked got my mower running again thanks

Great video. Thanks for sharing. 👍

nicely done ty

Very helpful & informative video, also he has alerted me to a new invention called a "torque wrench"

@mygiguser

6 жыл бұрын

I don't think a torque wrench works so well with the cork gasket. You are better off doing that very carful by hand.

@donf5710

6 жыл бұрын

I plan on using permatex ultra black....no gasket

@mygiguser

6 жыл бұрын

Don F let me know how that works out!

@californiaschoolbusdriver8532

5 жыл бұрын

Don F it doesn’t work. I tried twice, leaked both times.

Wow 😮 I never see before

You have learned me a valuable lesson in this video thanks

@shobud7561

27 күн бұрын

He didn't learn you anything he taught you something, and by this you learned something.

@shobud7561

27 күн бұрын

He didn't learn you anything, he taught you something and by that you learned something.

great video thanks

Thank you!!

Go video thanks for the help

Great video. Only suggestion is during the installation of the valve cover gasket, the new silicone should be liberally applied to one surface after both have been cleaned of oil and any debris, but more importantly, the liquid gasket should be allowed to form up for about 5-8 minutes before reinstalling the bolts that hold the valve cover on. Reason being, the liquid Selena the with just squeeze right out and create a potential gap. Additionally, only finger tighten during that part of the install. Let sit for 40 minutes and come back to re-torque the bolts.

@mygiguser

2 жыл бұрын

Thanks! Btw the gasket from the video is still working without any leaks.

You have set the engine ignition sequence for spark generation by the alignment of the coil and magnet. If the flywheel is not easily revealed, the same thing can be done by bringing the piston up to TDC on the compression stroke. This is exactly when spark will ignite the power stroke.

@1gtmach

Жыл бұрын

Spark will happen a couple degrees BTDC. Check it out. Bring piston to TDC and look at where the magnet is. Its past the coil ( magneto).

@northerniltree

Жыл бұрын

@@1gtmach My error, you are correct. Thanks for the clarification.

Great!! thanks 👍

Changed out the ignition coil on Kohler courage 590. Would the plastic cover not being on cause the ignition coil and spark plug boot to get real hot

Recently repaired somebody else's repair on one of these engines in a Cub Cadet, the intake rocker was not pressing against the valve at all, and there was no Torx recess in the rocker stud to make an adjustment secure. The nuts were the only thing retaining the rockers, I don't know what all was supposed to be in there, it was my first time in a Kohler engine, but it was one of many things wrong.

My mower wouldn't start tried several different things. Adjusted the valves per this video. Now I'm back up and running.

@mygiguser

6 жыл бұрын

Very good, congratulations!

I just got the same mower off my dad and it back fires when you idle down and when you idle up it makes a sort of rough banging sound as the cylinder fires. Could that be the valves? I think it's alway done it even new. Just never heard it from any other kohler 21.

Great video! How long until you can start the engine after using the liquid gasket? Does it need to dry first?

@mygiguser

5 жыл бұрын

Jason B yes it does need to dry, i would let it sit overnight.

Thanks for a great video. Very clear and concise! I'm working on a neighbors Cub Cadet with SV590-003 19 hpKohler Courage that was rough running, backfiring and eventually not starting at all but just backfiring. Carb was a mess so I replaced it as well as ignition module. then I discovered the flywheel key broken. replaced that and the new one sheared and it backfired again. Could valve adjustment cause that? Or what do you think it is?

@mygiguser

6 жыл бұрын

Broken flywheel key: Hitting a rock or stump, loose blades, or loose flywheel. Ignition problems maybe. Adjusting the valves should be easy to rule that out, then also adjusting the gap for the ignition coil kzread.info/dash/bejne/lI5ltcuKpa68cs4.html and then the solenoid problem, i describe in the description of this video kzread.info/dash/bejne/aqKio6WOm9bdqKQ.html what happens. How does your engine run in idle? Is it backfiring when it is running?

@anniversary4

6 жыл бұрын

Iwas most likely loose flywheel.Thanks it is running well now.

@suzieq8379

3 жыл бұрын

I have this mower kohler courage 19 I was told that the bots have a habit of coming loose on the fly wheel I always check mine, that will damage flywheel, also my bolts that holds the motor on were loose so glad I found that problem

@BlackFoxProduc

Жыл бұрын

Sensor on bottom of carb bowl is bad. Cheap to replace whole carb, ebay has them for a few bucks.

What is 4cylender tappet settings in kohler engine

Do these engines have a compression release ? Is the valve adjustment made at TDCwfen spark plug is firing? Do you turn engine backwards to bring it to TDC ? I assume the comp release holds the ex valve open to assist starting on some engines. I don’t know if Kohler uses comp real ease I. I would have to think it uses SOMETHING like that

@mygiguser

3 жыл бұрын

If you take out the spark plug, then you don't have compression. The valve closes by a spring. You can turn the engine back and forth at TDC to find the spot where both rockers are loose.

@thomasrose6962

3 жыл бұрын

@@mygiguser. On some engines a compression release is used as a starting. aid Why does tightening loos valves fix what most people think is a bad starter or Battery ? Seriously

Did you re-use the cork gasket? If so, did you use gasket sealer between the cork and the valve cover- or just make a new "gasket" with the black stuff?

@mygiguser

7 жыл бұрын

Ryan King i used a new gasket and the sealer.

You gotta be careful to double check your cover don't leak. Mine caught fire and melted all the plastic on the engine. Didn't damage anything beyond that lucky but the cost is about $100 for parts depending on what gets damaged.

@mygiguser

6 жыл бұрын

Retrogamer1010 it doesn’t leak, if you installed this right.

@4144758

Жыл бұрын

Yeah mine caught fire too that's how I know they're was an issue lol

do you not turn your flywheel to do this job???

When you set the valves, is the piston out, or in from the spark plug on the compression stroke.

@mygiguser

3 жыл бұрын

in. both rockers are lose. piston top dead center.

@ironhorsevinnie

3 жыл бұрын

@@mygiguser You needed to show as the spark slug still in . some people well a just with the piston any where .

I have a issue with fuel puddling at the mouth of the carburetor. The mouth of the carburetor should be dry. It seems there is blow back from the engine through the carburetor. Either the valve adjust is way too tight (no clearance) or perhaps carbon build up on the seat which would hold a valve open slightly.

@mygiguser

3 жыл бұрын

maybe the float is stuck? or the valve leaking

@richardgalli7262

3 жыл бұрын

@@mygiguser That is a good point. When I bought this well used (non running) gravely zero turn mower I had to rewire (it was butchered), replace missing and broken parts plus the carburetor because the fuel solenoid was not working. Yesterday I disassembled the new carb to inspect for crud and sticking float but all was well. I thoroughly cleaned all the orifices. The engine never sounded strong. Fortunately I came across your video and I inspected the valves. The exhaust clearance was way too loose and the intake had NO clearance. I just started it up and finished the lawn. IT RUNS LIKE A NEW MOWER! No lugging no black exhaust smoke. Thank you

Thanks for a great video-turorial. I'm going to make this repair in the next couple of weeks. How much hours your Kohler had on the moment of the job you made here?

@mygiguser

4 жыл бұрын

i think it was 180 or 200 hours

Hi Sir. Thank You for the instructions on the video. I have a question for You. To your knowledge, Do these engines have a cooling fan shroud that cover the cylinder head?

@mygiguser

4 жыл бұрын

Worms Wiggle yes they do

@harpin5457

4 жыл бұрын

@@mygiguser 👍Thank You Sir.

hi can you tell me if i set my cam timing marks on comp sroke piston up or down thanks

@mygiguser

Жыл бұрын

up

Hi,I have a Craftsman 4 years old Riding mower 21 hp Briggs & stratton engine . Motor hard to turn with starter ,new starter & battery--It make 3/4 turn & if if make 1 to 2 turn start right up. When starter can not turn it heat up ,without Spark plug engine move ok , I checked the valve clearance .004 & .006 -- Do you think it is a Compression release valve ,how I can be sure of that. Please help ,what other thing it could be?

@mygiguser

5 жыл бұрын

Sorry your comment was blocked by KZread, i just found your comment in the review list. If you think you have a problem with a compression release valve, just take the oil dip stick out, and see it it starts then. The oil fill hole will release the pressure, if there is any. But be aware of oil spilling out.

@dansofi

5 жыл бұрын

@@mygiguser I will try this , thanks

My feeler gauges are made in Usa, should I buy the type you have?

@mygiguser

5 жыл бұрын

What does it matter where they were made? As long as they are accurate you can use them.

@ionhunter

5 жыл бұрын

@@mygiguser Its an old joke "Usa Japan" because we cant believe its actually made in the USA.

Thanks for this video. I do think (IMAO) it may have been very helpful if it was explained the correct method to find Top Dead Center.Before making any adjustments. Just saying.

pull the sparkplug to turn motor

@mygiguser

3 жыл бұрын

Michael Collins that would make it easier

What are the gap settings?

@mygiguser

Жыл бұрын

read description, it's right there

Thanks for the great video, just one criticism, when the engine was started you kept talking and couldn’t hear a word you said.

@mygiguser

4 жыл бұрын

well, i’m not running a hollywood studio over here. did the best i could at the time.

What was the reason for doing this I have 2 of them takes a long time turning over to start

@mygiguser

9 ай бұрын

the gasket was leaking oil, and the mower didn't start very good.

Is a "Knocking sound" a valve problem?

@mygiguser

5 жыл бұрын

Hard to say over the internet without hearing the knock. But i would say no. Knocking is more a bearing on the crankshaft.

it is strange I bought 2 feelers and neither has an .007 and one doesn't have neither?

@michaelfornell4467

4 ай бұрын

Use a business card. It will be very close

I have a sv600 kohler 20 hp and adjusted valves to the correct measures but it gets stuck on the compression stroke sometimes and then spins over. Would u possibly know the issue?

Terminator does lawn engines now ?

@mygiguser

5 жыл бұрын

Yes, and it works!

I got MTD mower it Troy Built but it MTD they come out with Powermore 420cc engines Honda clone it a 2016 model great warranty 1 year lasted 1 year 2 months and blew up i put this engine on it 23 HP KOHLER single cinder twin valve i got engine off of Husqvarna LGT2554 Lawn Tractor fat guy owned it he broke the mower in half , half bent and half broke said he gofer hole . not that old of mower but i got it 200.00 and it fit ,moves in yard real good just little to much .You can cut your grass at 10 MPH and be done .

@mygiguser

4 жыл бұрын

joseph tate you got lucky finding that engine

@josephtate6949

4 жыл бұрын

@@mygiguser it been good engine i keep it serviced and maintained runs good .I have seen a lot of complaint's one guy was pointing out all the problems he was having and what you going to have but before he started talking he said he just lets it set outside in weather ? well that could be the reason to all your problems and tarp don't cost much but i didn't leave comment . so don't leave your equipment in weather ,take care of it it take care of you , that way i see things , great video mygiguser keep up great work

How you know your not on top dead center ?

@mygiguser

3 жыл бұрын

Piston is on top, and both valve rockers are loose.

@1gtmach

Жыл бұрын

Thats not correct. You could be on the rise , ramp, of the cam lobe. Pull spark plug and stick screw drive in cylinder and bring piston to top. Im not even sure if this is correct. Briggs calls for pistion to be 1/4 past TDC. I can not find info for kohler so TDC should be fine.

You know actually this is an excellent video , of course removing the hood ?? Just lift it straight up after it is in open resting position ! Remove wiring first for the headlight's ! The trick of aligning the magnet with the new ignition coil for top dead center making sure both valves are closed , that was ok " but I prefer removing the spark plug and using a long screwdriver to FEEL the Piston on top dead center by turning the flywheel slowly by hand and visually looking at both valves closed ! Also you said to remove the ignition coil wire because it was self igniting WRONG if the key is in the OFF position the ignition coil is grounded and cannot fire the spark plug ! Also you should specify that it is the hex screw that LOCKS the rocker arm assembly in place NOT the nuts that hold it down ! And if you use a silicone sealer gasket maker for the gasket it needs to be rtv black oil resistant silicone sealer type ! You can use only silicone and eliminate the cork gasket all together ! Just lay a bead about 1/4 inch all the way around the valve cover gasket wait about five minutes and put valve cover back on but do it straight on as in have it lined up with the mounting holes so you don't have to wiggle the valve cover around messing up the silicone sealer ! One more thing , when and BEFORE YOU attempt to remove the 4 top cover bolts IF they are hard to break free DO NOT FORCE THEM TO BREAK FREE OR EXERT HARD PRESSURE ON THE WRENCH TO BREAK THEM FREE !! you will wring the bolts off in the engine block if their rusted up or just gummed up always use break free lubricant or deep creep or similar bolt loosening deep penetrating oil on those bolts and spray the threads protruding under the plastic cover the threads of the bolts let soak in penetrating oil and if still hard to turn before you use hard force and break them off try a small electric battery powered drill with the impact setting turned down very very low so the drill will lightly impact the bolts but not forcefully turn them , the knock knock knock of the impact from the drill will 90% of the time save you from breaking these cover bolts off in the engine !!! One more thing when you use the feeler guage use .0005 on intake valve and .0007 on the exhaust valve that's thousands of an inch ! If you can't SLIDE the feeler guage back and forth across the rocker and valve gap with very little resistance it's TOO TIGHT ! and always always always after you have set both clearances turn the engine at least a few revolutions and reset the piston on top dead center then recheck you clearances on intake and exhaust valves again !

@blairsucks

2 жыл бұрын

.005 .007 not .0005 .0007

@Thumper68

Жыл бұрын

Don’t have to use black rtv. In fact peramatex red rtv is high temp and would be best for this application.

Good video except you said 0 point 0 7 and 0 point 0 5 wich would be 0.07 and 0.05 is 70 thousandth and 50 thousandths. It is point 007 and point 005 is 7 and five thousandths

@vintagevmax2410

4 жыл бұрын

Insert a 0.127 mm (0.005 in.) feeler gauge between end of 1 valve and rocker arm. Turn adjuster or adjustment nut (based on design), until a slight drag is felt. Hold in this position and tighten locking nut or setscrew securely. Torque setscrew to 7.9 N·m (70 in. lb.). After tightening recheck adjustment. Proper valve clearance is 0.101/0.152 mm (0.004/0.006 in.). 4. Repeat procedure for other valve on side 1. 5. Viewed from PTO end, rotate crankshaft 270° (3/4 turn) counterclockwise and align crankshaft keyway with cylinder 2, which now puts cylinder at TDC on compression stroke. 6. Repeat steps 3-4 for setting valve clearance on side 2. 7. Rotate crankshaft to check for free operation of valve train. Check for clearance between valve spring coils at full lift, or bending of push rod(s) can occur. Minimum allowable clearance is 0.25 mm

@slingshoter8783

4 жыл бұрын

@@vintagevmax2410 that engine only has one set of valves not 2 like you say. So you must of looked up the information for the wrong engine

Once the engine starts - I cannot hear you!

0.005" and 0.007". You dropped the 3rd zero on each one.

@mygiguser

3 жыл бұрын

where?

@donaldshimkus539

3 жыл бұрын

@@mygiguser you said zero point zero 5 and zero point zero 7. It happens. Ya just don't want a viewer taking it literal and then cursing you out 'cause it didn't work. Unless you were talking faster than I was listening, lol.

Excellent video. I have one correction though. When you say the clearance on the valves it is not 0.05 and 0.07 .......it is 0.005" and 0.007" . I hope this helps people because making it 0.05 and 0.07 would not do a good results. Thank you and good luck. Zee

@mygiguser

6 жыл бұрын

Zee Ilic i think i wrote the numbers in the description

One thing he forgot but not many people know is to pull the springs off the Pistons first then gap em. So I've been taught bye small engine builder.

@mygiguser

6 жыл бұрын

What kind of engines was your builder building?

@mygiguser

6 жыл бұрын

Look at Chris Fix video here kzread.info/dash/bejne/oXqMwbqqabquhKw.html

@jdovak1589

6 жыл бұрын

Jacob Lewis ...SPRINGS?? not on pistons...Rings, yes👍

@MrPackman20

6 жыл бұрын

Sorry to say pistons have no springs and there is no need to take the springs off the valves either ,please before you give advice know what your talking about.

@kellonpitts2650

5 жыл бұрын

@@MrPackman20 He must of thunk it had a piston return spring

N😮😮

Why are you talking with engine running? 🤫

@mygiguser

5 жыл бұрын

Trackhoe075 to make it more interesting. Thanks for watching 🙏!

This Video sucks. Camshaft position is not clear.

@1gtmach

Жыл бұрын

I agree.

You didn't show them how to find too dead center. Lousy video.