Always educational and entertaining. Thanks, Chris, and Happy Easter!

@ChrisMaj

Жыл бұрын

Thank you again, and Happy Easter to you too, Mr Boschek.

Quenched, Tempered and now Stress Relieved. Great work Sir!

@ChrisMaj

Жыл бұрын

All the stress went into the Dumping Hopper

Hello Chris. I love the video shot of the Kennametal knife tool in the middle of machining steel during roughing, the blue chips are perfect. For finishing the pointed diamond shaped tool VNMG 432 seems perfect.

Hate them sqwermy wormmies that wrap around the tool. For me they wait till the finish pass at the end of the cut just to try and wrap around the chuck... thanks for sharing. Have a good Easter. Charles

@ChrisMaj

Жыл бұрын

These bastards can ruin your job really quickly 😅. Happy Easter to you too.

thanks, very good job, i actually a student of precision mechanic in costa rica, i see a lot of videos, to update myself, thanks for your video

Great work Chris.

Thanks for the video. This was fun to watch

@ChrisMaj

Жыл бұрын

Glad you enjoyed it!

Great piece of machining mate thanks for sharing 👍 and Happy Easter to you and family

@ChrisMaj

Жыл бұрын

Thank you, and Happy Easter to you too.

Good thing the conveyor held up, shoveling out from even one of those would get old in a hurry.

@jasoncarn6956

Жыл бұрын

⁵⁵⁵⁵⁵⅚⁵⅝

good boy I would have done that too I wish you and your family a happy easter

Ale to jest naprawdę świetne wideo!👌👍

Great work.

great job...

I didn’t see your M72x4 go/no-go gauge. 😂

@ChrisMaj

Жыл бұрын

The three-wire method is all I need.

Ten tomu hezky dává-moje byvalá práce,,,,

Top Quality Work done...Keep it up

@ChrisMaj

Жыл бұрын

Thanks, will do!

holy crap...removed 3x the material than what was left...daggum! Keep em coming!!!!

@ChrisMaj

Жыл бұрын

Sometimes, it's just cheaper and faster to get a solid round bar than forging.

So just cut away everything that doesn’t look like a steering rod. Nice.

More chips than KFC...Happy Easter Chris

@ChrisMaj

Жыл бұрын

Thank you sir, and Happy Easter to you too.

Great job Chris, I take it that you used a horizontal machine to put the centres in before turning.

@ChrisMaj

Жыл бұрын

As always 👍

good job!! i love latte!! haha

That first pass looked like a 1/2" off!

@ChrisMaj

Жыл бұрын

0.315" per side

Стружки много. Видео классное, залипательное

Gday Chris, that was a massive job, how long did that take? Awesome job mate, cheers

@ChrisMaj

Жыл бұрын

One piece took almost an hour for the rough turning, and then they spent some time on the floor to cool down.

Love the work! I have one question, when feeding out against the head of the pin what was the speeds and feeds on that? I have always struggled with doing that.

@bigsmoke6189

11 ай бұрын

looked like he had constant surface speed programmed in,

that insert is just eating that steel rod 0o0

Machine propre ainsi que l'atelier, rien à voir avec les indous

Thanks for sharing 👍

Beautiful Parts! When you cut the threads, do you cut on both sides of the tool same amount or feed the tool in at an angle to cut more on one side of the cutter? Thank You!

@ChrisMaj

Жыл бұрын

It's a cnc lathe. You can choose if you want to cut both sides or just one side.

It would seem to me that starting a piece of material much closer to finished size would be more efficient and cost conscious. Disregard last transmission.😁

are those shafts getting hard chromed later?

that app looks pretty cool

@ChrisMaj

Жыл бұрын

Had it for years play.google.com/store/apps/details?id=com.pluckedstudios.machcalcpro

Chris, thanks for another great video! Any idea why someone chose to put over 3000lbs of steel in the swarf bin (not to mention the machine time) rather than making the eyes out of plate and using much smaller round bar? Respectfully curious (and someone has to ask!)

@kanetw_

Жыл бұрын

I'm struggling to find a good reason as well.

@kevind1865

Жыл бұрын

Far lower chance of failure if its 1 piece. You don't need to make sure the welder pre heated, post heated, monitored inter pass temps, wasn't drunk etc. If its part of the production line for a steel mill, the increased part cost might be 2-3 seconds of runtime for the mill. Engineers like to do the finger pointing, not be pointed at, so overkill it is.

@kanetw_

Жыл бұрын

@@kevind1865 Good point. I thought about weld quality, but I didn't realize this was for a steel mill.

@ChrisMaj

Жыл бұрын

They take a lot of beating, and it said on the print "make out of solid piece "

@tiredoldmechanic1791

Жыл бұрын

I thought the same too. It seems like they could have forgings made,

Chris na tym imaku masz 4 noże, jak jest z powtarzalnością po obrocie imakiem? Czy musisz za każdym razem mierzyć nóż? Pracuje od czasu do czasu na tokarce o podobnej budowie z hh620 i głowicą Multifix. Trzeba się mocno pilnować z wymianą narzędzi, szkoda że ktoś przyoszczędził na głowicy rewolwerowej

@ChrisMaj

Жыл бұрын

Zrobiłem raz krótki filmik o tym imaku. Bardzo dobrze się sprawdza. kzread.info/dash/bejne/p6am0qiQgrOradI.html

Those are rods and live ends for hydraulic cylinders

Might wanna make a hook for those pesky chip buildups.

I’m always jealous of your pre prepped shafts, it’s honestly the worst part. Beautiful work

@ChrisMaj

Жыл бұрын

Yeah, saves me a lot of time.

@flowjo12345

Жыл бұрын

@@ChrisMaj HUGE time saver indeed. As a fellow machinist who has done a lot of similar work I mean the beautiful work part. You should keep posting on Reddit. Not sure what made you tone it back but screw the children on there. They just wee boys anyway

@ChrisMaj

Жыл бұрын

@flowjo12345 Reddit is a tough crowd, and I just want to focus more on youtube.

@flowjo12345

Жыл бұрын

@@ChrisMaj you do your thing man. They indeed are.

❤

It looks like the insert cuts alternating left and right during cutting the thread? If so that would be very smart to load the insert symmetrically instead of basically using only one side when plunging in on say 29.5°

@ChrisMaj

Жыл бұрын

I think it's called alternate or zigzag threading. At least, that's what it's called in fanuc manual guide. About that other question, I don't really have an email that I can share for everyone.

That's a Kennametal top notch threading insert? How do you find rigidity in that grooving style holder. I've only used the basic holders for M68x6 thread on 316 type of material. Also tell the mill department to buy some high feed tooling 😉🙂

@ChrisMaj

Жыл бұрын

It's actually an ISCAR threading tool. That is the only tool I use for all types of threads, never had a problem.

@SipuliSopuli

Жыл бұрын

@@ChrisMaj There's bunch of manufactures who makes top nocht style insert these days. Just assumed it for Kennametal cause you seem to use it somewhat 🙂

Hello Sir Jo Aapne Calculater Use Kia Hai Kaha Se Download Kare

How much percentage % do you think you will get back for scrap on the original material cost?

@ChrisMaj

Жыл бұрын

Maybe 12 pack of Żywiec 😅

Dobra robota! Co to za aplikacja z gwintami?

@qualified_monkey8813

Жыл бұрын

CNC machinist calculator pro

@ChrisMaj

Жыл бұрын

Polecam, prawie wszystko tam jest. Brakuję tylko metrycznych tolerancji. play.google.com/store/apps/details?id=com.pluckedstudios.machcalcpro

FANUC?

Thankfully there is a chip hog.

Great work, but why didn't you start with a smaller diameter rod and then weld on a knuckle? That would have made the material cost much lower and probably cheaper overall once you add in the welding cost.

@ChrisMaj

Жыл бұрын

It's not really my call. Drawing says make out of solid round bar. Far lower chance of failure.

Listen process knucle rod...bro....

Did you get to do the milling on these Chris?

@ChrisMaj

Жыл бұрын

No, I don't get to do milling very often anymore.

@localele1

Жыл бұрын

@@ChrisMaj Become a high paid specialist.

How long did that part take?

@ChrisMaj

Жыл бұрын

Almost an hour just for rough turning and then finish and milling.

Вы охренели столько металла и энергии в стружку переводить!? Что приварить проушины не догадались? Вот нехорошие люди :)

@ChrisMaj

Жыл бұрын

Это не мой звонок. На чертеже указано, что изготавливается из цельного круглого прутка.

i wonder how much € they can earn from this (im just curious)

excellent machining! too bad for the wasted material...

@cambrowndrums

Жыл бұрын

you realize the chips just get recycled right?

@ChrisMaj

Жыл бұрын

The customer gets the bill, and we keep the chips 😅

@geenex6324

Жыл бұрын

@@cambrowndrums sure, but still a lot of energy and time wasted...

The drill disliked the video.

Ile mocy potrzeba, żeby uciągnąć takie parametry?

@ChrisMaj

Жыл бұрын

Całą 😅

0:31 why did you blur the numbers when we can still see them? ^^

@ChrisMaj

10 ай бұрын

It wasn't about the numbers. I've left some information at the top that wasn't supposed to be there.

@ipadize

10 ай бұрын

@@ChrisMaj ah okay

Whats the app chris?

@ChrisMaj

Жыл бұрын

play.google.com/store/apps/details?id=com.pluckedstudios.machcalcpro

My computer gave me a blue screen at 2:50 😀

@ChrisMaj

Жыл бұрын

And my lungs were little. "Are you smoking again "

0:23 Micheal Bay is jealous

@ChrisMaj

Жыл бұрын

Do you mean the film director?

@ChainsGoldMask

Жыл бұрын

@@ChrisMaj yes...the shot was very nice...looked like a movie

So your main product is Chips. At least by wight.

@ChrisMaj

Жыл бұрын

Yeah, blue chips is my specialty 😅

Such a waste of material. If there had been more of them to make ( not sure of the number to be economical) this would have been an open die forging job.

Yawn zzzzzzzz

대형 기업은 이런 바이트 팁 자체 생산이 아주 좋다. 이유 너무 많이 사용되고 조금만 사용해도 깨지거나 마모되서 자주 교체하거나 자주 점검해야 한다. 또한 자동화 로봇팔 CNC가공에서는 사람이 일일이 지켜 볼수가 없다. 즉. 정해진 바이트 마모예상 시간 이전에 미리 빨리 교체하는것이 좋고 기존 사용하던 팁은 과감히 재활용장 가거나 황삭에만 사용한다. 와. 바이트 팁 제조 공정 특징상 하루 제조 량이 어마어마 하면서 작은 인력으로 대량생산이 가능하다.

@user-jh1hc3vp6e

Жыл бұрын

그리고 바이트 팁 가격도 비싸다.