I was hoping for some details about the motor. Maybe even a link??

@EagleRun23

6 жыл бұрын

Here is the link to the speed controller. amzn.to/40ArXRf Motor Link amzn.to/422rIQh

@EagleRun23

6 жыл бұрын

this motor is NOT a drop in replacement. I had to redrill some mounting holes to get the sprocket to line up. Also the cheap kidd traxx gear box wont handle this for long. Eventually the more powerful motor will wear out these gears. At that point, Ill decide to do a total rehaul? or upgrade to a bigger power wheels. IT is VERY fast with my 30lb 2 year old son! Faster than he can actually handle. My 5 year old daughter handles it fine, but she is really too big at 41lbs.

@richardjoyner9266

5 жыл бұрын

Awesome, thanks. I work in a fab shop, so Ill let them tear up the gears, then get better ones.

@erikvincent5846

5 жыл бұрын

@@EagleRun23 how fast would someone your son's size take before the gear box wears out? I do electronic engineering, so the PWM controller board you have, I am very familiar with.

@EagleRun23

5 жыл бұрын

Erik Vincent it’s like a $20 machine so I didn’t have expectations of lasting long but 2 years later. Still running!

I built my kids a 20 cell 12V lithium battery for their normally 6V power wheel Lil' Quad and changed the motor and gearbox to a higher rpm 6/12V unit and this thing hauls. The lithium battery is alot lighter weight than the factory acid battery so that alone makes it faster. It runs all day long without heating up or running down and it's so fast that when I take them around the block I have to run the entire time to keep up with it. It carries my 2 and 3 year old kids together with no problem, combined the kid's weight is 75 lbs.

@flon4gzus

5 жыл бұрын

Do you have a video of how? Thanks!

hahaha nice upgrade. Looks fun

@EagleRun23

7 жыл бұрын

Thanks Rack!

I hooked up the Milwaukee 18 volt 5 amp hours battery to a 550 12 volt motor also installed a forward reverse speed controller

Did the stock gear fit the new motors shaft?Or is a new gear needed?

So, I did this... then the gears stripped on two separate four wheelers within 1 min. It would kinda be cool to see a slipper clutch like an RC car. I also thought about just transferring the whole gear box, motor, electronics from a 12v power wheels. It would be 2 speed with reverse. Then run an 18v battery.

Nice vid... What kind of esc is that?

What fabrication was needed to make it work?

Anyone have more information on the "quite a bit of modification" he had to do to get the new motor to fit?

Did yours have a little circuit board?

Yeah!!! First To All.... Really Nice Job.. And just like that a new project Begins!!!!!! 😂

@EagleRun23

3 жыл бұрын

Boom! good luck! hot rodding an e scooter soon!

What is the link to purchase the pinion gear for the shaft on the new motor? Or size? 12-tooth 32P ?

I’d like to upgrade my sons 6 volt to 18. He has the power wheel lil quad 6volt. Any links?

Came here because I’m about to buy one of these. Left knowing this dude wishes he had boys.

@EagleRun23

5 жыл бұрын

hahahaha

What model of drill do you have? I want to get those batteries.

What pinion gear did you use for the motor?

Don't you need a in line fuse?

Awesome

@EagleRun23

3 жыл бұрын

she was a ripper, finally blew up the switches and the kids are too big. Working on hot rodding a e scooter now! coming soon!

yes, its a great addition but unnecessary if your kids can handle the extra juice :)

Great video. I had a question Maybe you would know. I tried to hook up to 6 volt batterys to the same little atv you have and it is going backwards when it should of been going frontwards? Any ideal why, Thanks so much for your time

@EagleRun23

6 жыл бұрын

Ashley Moore if you only are switching the battery you should have no problem. If you did some wiring work, then the polarity on the motor is switched :) mistake I have made before! Thanks for the comment and hope I helped!

Did you reuse the same gear that was on the original motor? If so, how did you get it off the old motor? I have tried with pliers but it won't budge. Thanks!

@mattanfang

2 жыл бұрын

I'm also interested in how to remove the old gear on the original motor. Did you ever figure out a solution?

I had a smaller quad than that and I put 54v into it it went Atleast 30kmh then it blew up 😂

Doesn't Lithium battery requires voltage cutoff circuit or maybe is built in to the battery? I wanted to give the power drill battery a try but afraid I might overdrawn and kill the battery. Any thoughts?

@mrdumbfellow927

6 жыл бұрын

Qing Wu Milwaukee batteries don't have built in low voltage cut- off.... don't ask me how I know: )

@EagleRun23

6 жыл бұрын

ya, so thats another story, I did a video on that too! haha. I left one hooked up, it drained and went too low, wouldnt charge. I had to jump it to get the voltage up. now it charges and I own 3 batteries now.........

@EagleRun23

6 жыл бұрын

do you know how to jump the voltage so they can charge again?

I’m guessing it burnt out at six minutes 38 seconds? 😂 Good job, I just upgraded my sons to 12 V and was wondering if the motor could handle 18 but I don’t want to push my luck

Does the speed controller just lower the voltage that goes to the motor?

@erikvincent5846

5 жыл бұрын

It is a PWM controller, so what it really does is chop the voltage of 18V on and off really fast. Like a sugared up kid with a lightswitch.

Kobalt 24v is cheap so my mod will have an adjustable buck converter and run at 12v.

How did you hook up the wires to the battery. Also how was everything wired up. Thanks

@EagleRun23

6 жыл бұрын

the Milwaukee I used has slots. so a spade or a ring connector slides right in perfect. sometimes, on big bumps it will pop out, but thats fine! I like them loose so I can swap to fresh pretty easily. wiring is just per the package in the speed controller. The bat power goes into the speed controller and then to the motor. It is really WAY easy. I am not a pro, I have very basic electrical knowledge.

@Stiffsce

6 жыл бұрын

EagleRun23 thanks for your response. I didn't see any other videos from you on this subject. I noticed you work on guns, pretty cool. I enjoy them my self.

@EagleRun23

6 жыл бұрын

Stiffsce yes sir! This channel is just stuff I work on. (Mostly guns, haha) good luck got roddin your power wheels!!

I got the gear off the original motor, but I can’t fit it on the new motor as the shaft is a different diameter, what did you do?

@EagleRun23

8 ай бұрын

I ran through a few different setups. But I may have drilled one out too. Been a few years :)

Did you use a 550 motor ? Id like to use the proper size replacement

@EagleRun23

Жыл бұрын

i have links in the comments, but its been a good while, probably more and other options out there.

How long did this last? Did the motor or gears ever fail?

@cjbales1981

5 жыл бұрын

He decently repiled to someone else that 2 years later and its still running the stock gear box

Could you do a video on how you wired everything up.

@EagleRun23

2 жыл бұрын

Yes I probably should have done it differently this was several years ago and I definitely make videos different now than I did then I have a new electrical project coming up on a scooter but I salvaged I will go in more depth on that

@pbplayer91

2 жыл бұрын

@@EagleRun23 i appreciate the reply. Im working on my daughters old 6v quad that i want to juice up a little more for her sister when shes older.

Where did you get the speed controller?

@erikvincent5846

5 жыл бұрын

EBay or banggood. Just look up PWM controller

Please show the wiring. I can’t figure out how the switch connects to the speed controller / motor / battery

@EagleRun23

4 жыл бұрын

That's Our House hey this will be back on the work bench soon I’ll do an update and some repairs. I can look and do a Q and A

That is awesome!! Where were you when I was growing up? Haha!!

@EagleRun23

7 жыл бұрын

Orion Fixr haha neighbor kid just rode it 5 minutes ago. He has a big f150 power wheels. He was screaming with joy while his dad tried to chase him! Haha

@orionfixr7713

7 жыл бұрын

A few years from now, when that neighbor kid is building hot rods on the drive way, remember you got him started down that road!! Haha!!

Next mod I need for my girls Kids Trax ride is fixing it's very limited turning capability. Damn thing needs a full racetrack loop end in order for my daughter to just turn around without having to stand up and drag the thing to turn sharp enough. Anyone have any ideas?

@EagleRun23

6 жыл бұрын

The stops are molded in the plastic body. you can easily cut them back and increase turning radius. I did this! just a razor knife no problem. Start small! if you go too much it turns too much and can be unstable. but mine does good dounuts with the right driver!

how did u get the motor to center up

@EagleRun23

4 жыл бұрын

Jose Juarez I’ll film an update soon and see if I can show more.

How did you swap out the gear on the motors especially if it used a round shaft?

@EagleRun23

2 жыл бұрын

i fooled with a few gears off amazon, all were cheap, i measured the shaft of the output and found a gear that fit. this one was pressed on. some have set screws.

@seth3342

Жыл бұрын

@@EagleRun23 do you have a link?

@EagleRun23

Жыл бұрын

@@seth3342 Here is the link to the speed controller. amzn.to/40ArXRf Motor Link amzn.to/422rIQh

vehicle run time? Just wondering. Thanks.

@EagleRun23

4 жыл бұрын

Mike Bohn she rips! But I say 20 min? I have room for 2 batteries so I take a spare and have a good 40 min.

What if you just leave the 6v motor and just hook up 18v battery any changes ?

@EagleRun23

3 жыл бұрын

She will go for a while. We did that. The motor swap was just because the original one burnt up :)

@319speed

3 жыл бұрын

Mine burnt up in 20 minutes

@EagleRun23

3 жыл бұрын

@@319speed ha. Mine ripped until a ruined all my batteries! Kid is 5 now so he has bigger stuff.

why is it not going forward

Can you post a link to where you got the speed controller from please

@EagleRun23

2 жыл бұрын

Hey I love to help but I dont have that handy, this was a few years ago. I am sure its here in the comments.

How do you charge it up

@EagleRun23

Жыл бұрын

standard milwakuee cordless drill charger.

This dude sounds like an actor I can’t think of. It Danny McBride, but close.

@EagleRun23

4 жыл бұрын

woa! ! I dont know who that is, but ok! haha

How did you take the motor out?

@EagleRun23

5 жыл бұрын

leticia perez it has 2 small bolts :)

@leticiaperez5397

5 жыл бұрын

EagleRun23 after you take those small bolts Does the motor just comes out just like that, can you be a bit more specific please!

@EagleRun23

5 жыл бұрын

@@leticiaperez5397 Hey, wish I had more info for ya. This was over a year ago and the thing still rips! so fast. I didnt really film a tutorial. so I dont show many details. If you get in there you can see the gear box is super simple, gather your measurements and the motors are really easy to find. just make sure the diameter of the shaft is the same and the bolt pattern and its virtually a straight up swap.

@leticiaperez5397

5 жыл бұрын

EagleRun23 Thank you so much for all the help!

@leticiaperez5397

5 жыл бұрын

Sir.sorry to bother,but how did you put the pinion gear on new motor shaft? We ordered the same the same motor as you did,but now the pinion gear don’t fit.

Can you put the link up for the motor you got

@EagleRun23

2 жыл бұрын

scroll through the comments, i think its in here.

List the motor or link

@EagleRun23

3 жыл бұрын

This was a few years back. Hit the pinned comment or in the description

Oh man this looks like too much work 😫

@EagleRun23

3 жыл бұрын

it wasnt so bad. I was intimidated at first.

Trying to find a video on how to make it reverse

@EagleRun23

2 жыл бұрын

Ohh interesting. Ya I bet that’s possible.

Hi there.im tempted to ...put 18v bosch battery into my daughter 6v audi r8 spider....ride on car....its so slow...and does dies in no time ....or maybe 24v battery 😱😉

@EagleRun23

4 жыл бұрын

tomasz kus 18 v shouldn’t affect the reliability but 24 will cook that motor after a few sessions :)

Would have been a nice video if it more details ok this wire comes from the battery and goes to here. This is just a waste of time

@EagleRun23

2 ай бұрын

It’s an idea. These models don’t even exist anymore.