Thanks so much I was able to fix my dryer today from watching your video and saved some money for not calling the repair guy lol

@QuickAndEasy5MinuteAppliance

6 ай бұрын

Glad I could help😊😊😊

This video was extremely helpful in diagnosing what was wrong with my dryer. One thing about this video is the distracting whistling in the background.

@QuickAndEasy5MinuteAppliance

2 жыл бұрын

Hi Lily, Here is a new version without the whistling .

The whistling is driving me craxyb

Thank you so much, I was ready to purchase a new dryer. After following the video, the dryer is working fine.

Thank you. Perfect!

Glad I found your video, after testing it turned out to be the switch that was behind the thermostat that you removed...by the way I took out just as much crud if not more than you did.lol Thanks man 👍

@lTzImmortal

3 жыл бұрын

The farthest back ? Mine are not reading any continuity there how did you replace them?

How is he talking and whistling at the same time

Most informative. Thank you so much for this great help video

@QuickAndEasy5MinuteAppliance

2 жыл бұрын

Thanks Richard👍😊

Hey I need a even heat control board for this exact model your working on.

In need a even heat control board for this exact model of dryer your working on, do you know where to get one

Thank you!!

@QuickAndEasy5MinuteAppliance

3 жыл бұрын

You’re welcome👍

What type of multimeter is that you’re using.

@QuickAndEasy5MinuteAppliance

4 ай бұрын

I’m not sure the brand, but I would order one from Amazon that has the audio feature so you hear a beep when checking continuity.

Big help. Thanks.

@QuickAndEasy5MinuteAppliance

2 жыл бұрын

Thanks Daniel😊

slammin the therm werks! WOOOOOOOOOOOOOOOOOOOO'

Wts the screw on back lower middle i started to unscrew n somthin is falln n i cant get to it

I replaced the thermal fuse and it worked but when I went there 30 minutes later it wasn’t working again and the thermal fuse is again not showing that it has signal. It says on your main page that y’all can do live help, how do I do that and how much does it cost? I thoroughly cleaned out all lint and stuff so I don’t understand why it’s overheating

@QuickAndEasy5MinuteAppliance

Жыл бұрын

Great Question Lindsay👍 Click Here to Get Live Expert Help From Me For Just $5.00: kzread.info/dron/GpInAejvpfVVE4FHB_L-Dg.htmljoin I can help you to get your dryer going again👍

Most videos asked to remove the screws on back to access inside. I removed all the back screws but it would not budge. Then this video showed that for the older models, you need to remove front bottom. After testing for continuity, I found the farthest one inside faulty. Was tempted to do a quick test for a few seconds by bypassing the fuse (Before ordering the part) but chickened out

@QuickAndEasy5MinuteAppliance

2 жыл бұрын

You are wise👍 Sometimes if you slam the round part of the hi-limit on concrete it will reset.

@lindsaymccarver6097

Жыл бұрын

How much was the part? Also, what is the furthest one back called?

@QuickAndEasy5MinuteAppliance

Жыл бұрын

Hi Linda, it’s called a thermal fuse. It’s about 20.00 from Amazon👍

Is it a fuse after the thermo fuse? This is what is the high limit fuse you refered to, that is what's not working for me.

@QuickAndEasy5MinuteAppliance

4 жыл бұрын

Should be the thermal fuse on the back.

@jamesfrancis6423

4 жыл бұрын

@@QuickAndEasy5MinuteAppliance it worked for me so far. I smacked it against the concrete basement floor and it reset after the third time. Cleaned out the blower fan tunnel put everything back together and gave it a try.

What is it when your electric dryer( Frigidair DE500ADW5) works as it should and shuts off at the end of the cycle, but the heat is staying on. Checked the heater, is not grounded.

@waltersobchak7275

3 жыл бұрын

Unplug that fucker please. It may burn down the house. Im sure you know that though

That looks to be the element overheat *thermostat*, not a thermal fuse. Fuses by definition aren't revivable after they blow (the internal circuit contacts melt). Bi-metal thermostats, when working properly, auto-reset when they cool below the trigger temperature. Attempting to forcibly "reset" it by slamming it against a surface isn't a good idea. It has already failed so wouldn't be reliable. There is also a thermal fuse on the element housing. The other thermal cut-off fuse on the blower housing monitors the exhaust air temperature (not the element) and typically makes the dryer go dead when it blows. The element overheat thermostat and fuse only affect the heating element operation, the dryer otherwise still runs.

Didn’t work for me. Thermistor didn’t have continuity nor did the next two. Still no heat.

My for dryer has been broken for 2 years hopefully it will get fixed after watching this

@QuickAndEasy5MinuteAppliance

4 жыл бұрын

Please let me know