This man should be called "Zero Gap" keep them videos coming. Loving your content and dedication!

This is my setup of trimmer for my daily job as a barber. And I tell you man, there is nothing better! The power, high rpm, battery, and the adjustment for lower rpm for kids of the renpho/kemei allied with the Wahl blade is miles away from anything else I have seen.

@edounboxingofficial

3 жыл бұрын

Yea, u right bro

@Man_eee

2 жыл бұрын

For this trimmer is this wahl blade better than the andis gtx blade? Also what is a cam follower & do I have to buy one?

@mantis780

2 жыл бұрын

@@Man_eee I have a wahl blade on mine, you need the cam follower from the Wahl detailer. The andis blade I have no idea if it fits. With the Wahl Blade it gets a little more noisy than with the original blade.

@Man_eee

2 жыл бұрын

@@mantis780 Damn I sent you a reply with links to cam followers from Aliexpress that I think will fit, but I guess my comments got took down

@wanmangeng5957

2 жыл бұрын

I'll take it a step further. In the history of humanity, there has never been a clipper, or trimmer with a better value proposition. I can't believe how good and powerful it is. I have the Renpho, but i'm buying the Kemei trimmer next, as I believe they're essentially the same. Unbelievable.

Did this as well and used a stanley knife to make the hole for the cam follower a little bigger to make the motor fit. That and not fully tightening the screws and its a great combo! Better than the cheap replacement fake Kemei blades online...

@faizantahir9598

10 ай бұрын

I'm about to do this mod too - do you mean the screws for the cam follower or the screws attaching the blade to the trimmer should be less tighter?

@FernandsLiveShowShow

10 ай бұрын

@@faizantahir9598 tightening the screws of the blade to the trimmer. Not too too tight but enough to secure it in place

@faizantahir9598

10 ай бұрын

@@FernandsLiveShowShow Thanks - will give that a shot

The problem with that is your screws are to tight. Back off the screws just a little bit and you will get the desired speed. Also there are to small tabs hanging off of the back of the cam follower, cut those tabs off and you should be good.👍🏾

hey bro where did you get that little white attachment for the blade attachment ? when i purchased it it didn’t come with that

Will you make a review if the style craft smaller blade will fit this trimmer the blade resembles the andis slimline li blade..

The wahl 5 star Blade is pretty cool, but there is a manual way to zero gap the follow come Blade. I have a trimmer which I used the trick for and it works perfectly

@edounboxingofficial

3 жыл бұрын

Show me. You have the video on KZread?

@odumosudnewshelf9192

3 жыл бұрын

@@edounboxingofficial no I don't hv the video but I can take pictures of my blade and make illustration on how it's done

@edounboxingofficial

3 жыл бұрын

@@odumosudnewshelf9192 ok kool. Can you send it to my Instagram?

@odumosudnewshelf9192

3 жыл бұрын

@@edounboxingofficial what's ur Instagram ID

@edounboxingofficial

3 жыл бұрын

@@odumosudnewshelf9192 @edounboxingofficial

Hi, please can you guide me to speed the engine per minute or the same rpm or give me the link of your program Thank you for your excellent channel❤😊

I GOT THAT TRIMMER, HAD TO CHANGE THE BLADE OUT, THEN IT HIT!!! VERY NICE... PEACE BRO

@edounboxingofficial

3 жыл бұрын

Yea, me too. U have to change the blade too

@edounboxingofficial

3 жыл бұрын

@@oeshkoer that you are right too but less RPM will not hit like high RPM

@tep1236

3 жыл бұрын

@@edounboxingofficial it speed differs bc of the cam follower, if the cam follower is tight enough to run with the motor it should run in the fastest potential, but if its tighter it might run slower and damage the motor in the long run

@tep1236

3 жыл бұрын

You did same as edo?

@sleiteruriel

Жыл бұрын

@@tep1236 puedes dar una explicación para ajustarlas bien, se necesita otro accesorio?

U need the whal detailer cam follower....for it to work correctly....

@edounboxingofficial

3 жыл бұрын

This is the cam follower that I have

I lost the tensioner spring to my kemei km-5027 trimmers. Any ideas where to get one, or even what it looks like?

@edounboxingofficial

3 жыл бұрын

Oh that I dont know

How was it after you put oil on the blades? 7300 rpm?

Ciao amico quel pezzetto di plastica bianco è in dotazione con la lama wahl? O con il trimmer kemei?

@edounboxingofficial

2 жыл бұрын

The white piece (cam follower) doesn't come with Wahl or kemei. But it comes with some AliExpress T-Wide blade

Salve, quel pezzo bianco da mettere alle lame wahl dove lo trovo? Grazie

Good job sir 👍💈💈

@edounboxingofficial

3 жыл бұрын

Thx bro

Does This fit for km 658

i want to upgrade my kemei to be more sharp on lines and bulk removal, should i upgrade to monstertrimmer blade or just buy a new 10000 rpm trimmer

Dope brotha!

@edounboxingofficial

2 жыл бұрын

Thnx

mano quisiera ver toda desmontada

Lencepro bucağına uyumlu mu ?

You can order them on line

@edounboxingofficial

3 жыл бұрын

What and where?

nice 🔥🔥🔥

Kemei 5027 or kemei i32??? Kindly advise

@edounboxingofficial

2 жыл бұрын

5027

@mokamsid

2 жыл бұрын

@@edounboxingofficial thnx for replying

🤔 It looks like you have a hero cam follower as opposed to the detailer. What's that new RPM app?

@edounboxingofficial

3 жыл бұрын

RPM Guage. I never had Wahl hero before

👍🏻

I am very new to barbering, where do we buy guards for this trimmer? Please help.

@edounboxingofficial

2 жыл бұрын

I haven't seen any trimmer guards for sale before

@dayshoncooley5941

2 жыл бұрын

Wahl gaurds for wahl detailer

@dayshoncooley5941

2 жыл бұрын

With the same blade he used the wahl detailer t wide blade std

Which cam foller are you using?

@edounboxingofficial

3 жыл бұрын

The normal white cam follower for cordless detailer

@167champ

3 жыл бұрын

@@edounboxingofficial thanks. Ive seen other white cam followers so ill look into those. Appreciate it.

A lamina dela e boa ?

Hi bro, which one is better kemei 5027 or Vgr 063

@edounboxingofficial

3 жыл бұрын

Both are good depending on what u want

@asimosman9873

3 жыл бұрын

@@edounboxingofficial for personal use, because some people saying Vgr is better because it is metallic, now I am confused and don't know which one to buy, can you please suggest one ( I am not planning to change the original plade). Thanks for your great videos and reply.

@laiwoh5001

3 жыл бұрын

What name of app you use brother?

@edounboxingofficial

3 жыл бұрын

@@laiwoh5001 play.google.com/store/apps/details?id=jp.nas.giri

@carlosjaimes4141

3 жыл бұрын

Cenwees out the box ... I’m not a barber but I can feel, see and hear the difference with the cenwees compared to other trimmers

Nice ✅

🇧🇷 👏🏽

What app did you use? For checking the rpm

@edounboxingofficial

2 жыл бұрын

Rpm Guage

Dope trimmer

@edounboxingofficial

3 жыл бұрын

Indeed

Is in the wahl t blade Package the come follower the Adapter included??

@edounboxingofficial

2 жыл бұрын

Cam Follower is not included in wahl T-wide blade

@DER_OSMANE

2 жыл бұрын

@@edounboxingofficial can you give me a Link for cam follower on aliexpress i have Buddha from kemei i will modify too! Please

Name app rpm please

@edounboxingofficial

2 жыл бұрын

RPM Guage

I thinks 5027 Moter not power full much bhter 5027

Does This fit for km 658