Learn more about your *97-01 Honda CR250* here! - goo.gl/iZuLQc

@josephkampsnider5564

6 жыл бұрын

Hey John, I got a 01 cr250 with a 265 big bore and the keihin , I run motul 800 , I have v force reeds and gnarly pipe and turbine core 2. I'm at sea level running 175, 48, 3rd clip , I'm getting a lot of spooge coming out the pipe not just the usual amount like leaking down to swing arm amount I was thinking about going down to a 45 what do you think

@Fixyourdirtbike

6 жыл бұрын

I have a question and please don't be offended. Are you really heavy? I'm very heavy, and I've ALWAYS had excess oil out of the pipe on EVERY 2 stroke I've owned. Do you see any other indicators that your running rich?

@josephkampsnider5564

6 жыл бұрын

No bro 175 , I never had an excessive amount of oil until I switched to the motul 800 the bikes set up.for woods and has woods pipe so it does fall flat at the top of the power in 2nd gear but that's to be expected it runs great just lots of oil

@josephkampsnider5564

6 жыл бұрын

And I run 50:1

@Fixyourdirtbike

6 жыл бұрын

Were you running full synthetic before?

I finished rebuilding my carb on a 250R 99' today, thanks for the info man, greatings from Croatia, Europe

Just discovered your channel. Great content would have subscribed anyway but hearing Amon Amarth in the beginning of the video I was like what? dirt bike related content AND a metalhead? Subbed immediately!!! Haha greetings from Greece

Just gor a cr 250 1998 cannot wait to ride it gona have to give it a service first though thanx! Liked amd subbed

I love all these videos, helped me a ton! Thx Jon!!

@Fixyourdirtbike

8 жыл бұрын

+Derek Rose Glad to help!

All balls makes rebuild kit for this carb just got it and installed it works great

Man, The videos are fabulous. They save me so much time and they are very entertaining - Thanks. I recently bought a 2002 KX 250 that the seller had “done a bunch of work on” and snuk on to a MX track with his buddy to test it. He went over a jump and at the bottom the owner was installing a drain pipe and he slammed into it. When he got out of the hospital he put it up for sale and I bought it with a crumpled front wheel. I replaced the wheel and will likely have the shock stanchions straightened to solve that problem. When I cranked it up to run the gas out for the winter, it idled a little high when cold but as it warmed up the idle became extremely fast. I estimate about 5000 to 6000 rpm. It was so fast that the kill switch did not want to stop it I suspect that happened to the last rider and he just did not bother to mention it to me. I think it is probably an air leak somewhere in the system but I haven’t worked on bikes since the late 1970s. What would you suggest that I check as possible problem areas? David Floyd

@Fixyourdirtbike

6 жыл бұрын

David Floyd Thanks! I would check the jetting, and if you have a throttle stop screw, make sure it lets the slide fully close first. When your revs take off it's due to a surge of oxygen.

@davidfloyd9962

6 жыл бұрын

Thanks for your insight. 1. I will check the throttle slide to verify that it closes all the way and fits well enough to rule out unmetered air. 2. Take the carb apart and check the jets for correct numbers versus stock. Is that the recommendation? Thanks, DCF

@Fixyourdirtbike

6 жыл бұрын

David Floyd That's a great start!

thank you so much this was a great help

thank the vid was a big help man

Not a single comment?? This video is so helpful, thanks!

@Fixyourdirtbike

8 жыл бұрын

thanks man

Thanks for the help bud working on my 1985 car 250 and I was wondering how this was done they are still pretty close to the same

@Fixyourdirtbike

3 жыл бұрын

Pretty much all carbs are the same, but don't tell anyone...

Hey John, Great video! I fixed my bike thanks to you. I wanted to compliment you on how efficient this video was. Most "how to" videos are slow and the narrator rambles on for days. You spit out the information quickly and stuck to the pertinent information. Thanks again!

@Fixyourdirtbike

8 жыл бұрын

+Bryce Sager Glad I could help!

How do you remove the needle seat, I see that you don’t do it in the video but isn’t there a o-ring in there? If so I have to replace mine but I can’t figure out how to remove it

Is the carburetor choke up or down, what position is it to start the bike? In cr 1983 125r

I have a 1997 YZ250 2 stroke I forgot the count turns on the idle screw when I took everything out what is the What is the adjustment on the idol air shrew in the adjustment on the joke which turned all the way in on both despite as a bore kit and exhaust I can't seem to get to kick over

Ameizing info ooooh very nice

I have a 1996 Yamaha YZ250I forgot to count the terms on the idol air screw how can I get the bike to start what's the adjustments on the choke lever one shrewd all the way in and what is DA adjustment on the idol air screw once turned all the way in Are you believe this bike had a bore kit and has exhaust

I just bought a 1993 and it has this carburetor in it

great video man but quick correction you can still buy the bowl seal there are a few kits on ebay that you can find that include it

@Fixyourdirtbike

7 жыл бұрын

Hey good to know! Thank you. In the video I was referring to OEM, but I did not specify. Good catch!

hows it going john , any idea of where to buy a good carb rebuild kit? i have a 1998 cr250 , my carb leaks gas out of the hose while the bike is on/off, im thinking it might be the needle valve , i just dont know the part number thanks

@Fixyourdirtbike

4 жыл бұрын

That does sound like your float needle is leaking. It's either out of adjustment or the rubber is bad. I usually go to Revzilla's OEM parts finder for single stuff like that. bit.ly/30YS1bt

I know this is for a CR250, but my XR650l carb slide looks like its scorched our something on parts of it. Is this just normal wear and tear or do i need to get a new one?

@Fixyourdirtbike

4 жыл бұрын

Sounds like your bike was backfiring at some point. If your slide is still smooth and solid you should be fine.

On my Honda CR500 the idle adjuster is on the choke knob. How do I zero this out? Which way do I turn it and how many clicks do you recommend for easy start up and good idle? Do I adjust it while the knob is in the up or down position?

@hugoinovamotorscb500gonzag6

Ай бұрын

Também tenho o mesmo problema não estou conseguindo deixar a moto na lenta

I'm surprised that putting the stock Reed cage back on didn't fix the problem. But I just thought I should let you know hopefully you can get back to me and give me some kind of tip that would help I will say that the mid-range top-end power is a lot better now that I put the Needle in the second clip position. And I cleaned out the passageways but aside from that it's still has no bottom end at all it bogs out at the bottom when you were riding when you're honest and it performs completely normal aside from the fact that it doesn't idle which is so strange it revs up high comes down normal I don't know what's going on

I need help what’s the part called that sits on top the carb I don’t have the little metal bit holding the Throttle cable in

@Fixyourdirtbike

4 жыл бұрын

That's built into the throttle cable, so a new one should have it.

Is there a chance that the bike doesn't work correctly when there's a little damage on the head of a jet? (Where you put your flat screwdriver)

@Fixyourdirtbike

2 жыл бұрын

Yes

Can I swap my 97 250 carb to my 01 250 the 01 doesn’t have the power jet cylonoid thing

@Fixyourdirtbike

5 жыл бұрын

You should be able to swap carbs without much trouble. You might need to play with the jetting though.

I'm thinking about buying an entirely new carburetor but they're so expensive so I was hoping you could help me out

@Fixyourdirtbike

5 жыл бұрын

Lets move this over to Facebook messenger so I can keep track of everything. facebook.com/FixYourDirtBike

Why is the needle on my power jet cut..cr250 honda

hi I have a 1995 cr250r witha hot rods crank, wiseco piston, for gold series pipe n power core 2 muffler, boysen power reeds, twin air filter. the carb has I believe the stock jets but not positive and the plug is b8es I believe, sometimes I put the ngk r version and I run ams oil dominator at 32:1 with 93 octane gas but my problem is if the bike sits it won't start without pulling the plug n priming it with gas but the plug looks kinda wet if I try kick it first then pull it but once I get it started it won't idle not even really with choke on only for a sec then wants to die. after running it n warming it up it will start back up usually first couple kicks but sumtimes it won't and I have to prime it all over again. ive done plug chop n the plug don't seem too bad or dark but any suggestions to problem or what to do maybe? I would really appreciate it I hate having to worry about shuttin my bike off in the trails. thank you

@MemeRider

5 жыл бұрын

Get a pwk 38 air stryker, and move your needle up 1 clip position

No one talks about that power solenoid cable that connects to the side of the carb....what is that for.....its called the power jet solenoid harness

My float valve seat is leaking . When I turn the gas on it fills the bowl and leaks everywhere out of the hose . How do I remove the valve seat to replace the O ring

@Fixyourdirtbike

6 жыл бұрын

Have you tried adjusting your float tab? It may be out of spec and not seating the fill valve all the way.

Like I said before I have a 1997 Honda CR250R equipped with a PJ 28l carburetor and a power jet selenoid. Like I said I just don't know what's going on but it will not hold an idle even if I increase the pilot jet up to a 70 stock was a 55 and for some reason it still will not hold an idle there. I've cleaned out the passageways I've literally done everything I can I'm sorry from the float Bowl height which would have been changed from the new float valve but it should only be a minor change not as severe Jane but I don't know if the float Bowl height would cause a rich condition at the bottom end 1 and 2 I don't know if it would cause the bike not to idle on its own. Before all of this happened the bike works fine only after I put the new read cage assembly in it started doing this. I put the stock Reed cage back in and it's still doing it as well I thought I should let you know that. Because I thought by putting the stock one back on maybe it would fix the problem but it hasn't fixed it at all

@hugoinovamotorscb500gonzag6

Ай бұрын

A minha nao para na lenta

I don’t know if you still see these comments, but I’m currently rebuilding this carb and bike. I was wondering where you got your Allen screws? Did you buy them specific or just from a local hardware store?

@Fixyourdirtbike

5 жыл бұрын

Local hardware store

@chasem_0499

5 жыл бұрын

Fix Your Dirt Bike I realized it was a poor/self explanatory question after some contemplation but I still really respect and appreciate your feedback to just about any comment I’ve seen. Videos kill too. To the point and everything you need. Keep rippin!

@Fixyourdirtbike

5 жыл бұрын

Thanks!

@chasem_0499

5 жыл бұрын

Jumping back in here real quick to ask a question. After rebuilding bike top to bottom, I noticed my carburetor intermittently dumps fuel from the overflow hose. At one point it just poured out with the bike sitting still as i filled the gas tank, and it now drips from it but pours when leaning the bike after adjusting the floats a little. I have tried adjusting the floats around to see what helps and the flowing still happens and the bike idles higher now which I’m assuming is the leaning of the mixture due to trying to prevent too much fuel. I have done some research and found some people simply swapping the float needle with an OEM and fixing the issue, but I’ve also heard of an O-ring at the bottom of the valve seat going bad and leaking through, this having been on various different models. Sorry for the long explanation, but my question is if it is possible to remove and if so how to remove the float valve seat? And is it safe to assume that it is a needle/seat issue and to replace those then readjusting the float? Let me know, thank you!

@Fixyourdirtbike

5 жыл бұрын

Are you leaking from the overflow hose or the bowl? Unfortunately the float valve seat is part of the carb body and can't be replaced, only smoothed out.

I’m having problems with my 2001 cr250 carb... I actually took my lectron off my bike and put my mikuni back on . The lectron was nice but I feel like I lost a lot of power so I put the mikuni back on but now the bike is so hard to start, the carb is overfilling itself and dumping fuel out of the drain hoses. The carb itself is spotless inside but the floats are still sticking? Think the float height may have went out of adjustment? It’s been sitting in my room for months, I never use to have these problems with this carburetor before

@Fixyourdirtbike

3 жыл бұрын

Interesting. I would bet the float valve seat O-ring is bad. Super easy fix. I'm more interested about your lectron not performing. Did you talk to them? I picked up a VERY noticeable amount of power with mine.

@MrSmokeingood

3 жыл бұрын

@@Fixyourdirtbike well with my lectron my biggest issues with it was that yeah I feel like I lost some top end ...it definitely helped down low in the throttle range though. Also it seemed to overfill easy , say if I were to lay the bike down after I picked it up it was hell to start back up cuz the carb would be filled all the way up. As far as performance goes it definitely ran good but I couldn’t seem to fine tune it to run like my mikuni use to. I’ve tried all the adjustments too, maybe a different metering rod would help

@Fixyourdirtbike

3 жыл бұрын

Huh, are you riding at a high altitude or super low temp?

@MrSmokeingood

3 жыл бұрын

@@Fixyourdirtbike nope I’m at sea level in sunny California I’ve heard other people having issues with the floats sticking n overfilling too

@Fixyourdirtbike

3 жыл бұрын

Well...shit

Where can I get the whole float assembly for this carb

@Fixyourdirtbike

3 жыл бұрын

rockymountainatvmc.com

helpful videos I love em all but just a tad too fast on this one lol

Didn't think they made a 1997 model year CR250?

What's the little hole in the back left side of the bowl

@Fixyourdirtbike

8 жыл бұрын

+badnews300ex I'm not sure which hole you're taking about. All I can think is the overflow hole. Can you post a pic on the Facebook page so I can see what you mean? www.FaceBook.com/FixYourDirtBike

Why is there missing audio

What should the float level be at??

@Fixyourdirtbike

6 жыл бұрын

goo.gl/x1PrNM

@pnwtactical

6 жыл бұрын

So i took it apart today and made it like if the carb is right side up and lift the floats till the flat across and push up a little bit the needle hits the shock if that makes sense

@pnwtactical

6 жыл бұрын

Or should it not hit the shock at all?

@Fixyourdirtbike

6 жыл бұрын

Hold your carb sideways and adjust the float tab so it touches the float valve spring, but does not compress it.

Hey man, i have a buddy with a 97 CR250... he is experiencing an intermittent bad bog like it is out of gas. he has went through the carb and nothing looks out of place. its getting spark. any ideas?

@Fixyourdirtbike

5 жыл бұрын

How frequent? At what throttle position/rpm would you guess? Is it an acceleration bog or a random bog at a steady speed?

@pik2490

5 жыл бұрын

@@Fixyourdirtbike you can start it up and it will idle fine and all of a sudden will act like it's running out of gas. Sometimes it will start and run good u till it bogs out at low rpm

@Fixyourdirtbike

5 жыл бұрын

Ok, so it sounds like it idles fine until it warms up. What about riding?

@pik2490

5 жыл бұрын

It will randomly bog down and die at low rpm.

@pik2490

5 жыл бұрын

@@Fixyourdirtbike It will randomly bog down and die at low rpm. Sometimes it will run good. Sometimes it is hard to start.

Mine just poors gas out of the overflow nipple, idk whats happening help.....

@caidenzagala7420

3 жыл бұрын

Found out whats happening, there are 2 tiny rocks were the float needel goes to stop the gas but i have not got them out yet

@caidenzagala7420

3 жыл бұрын

And it still doesn't start

@erod6611

3 жыл бұрын

Caiden Zagala I was having the same problem on my 01 CR 250 mikuni TMX carb. I ordered a float needle gasket replacement from JD jetting it’s like 6 dollars. Pull the carb out, remove the bowl then take out the white plastic retainer clip inside, remove the floats and take out the needle (remove 1 retainer screw) and gently pull it out. The o-ring on the needle seat is probably the culprit. I replaced mine and it was good to go after that. Replaced stock jets with a JD jet kit and it runs great. Still need to adjust jetting a bit but it doesn’t leak at all any more.

@erod6611

3 жыл бұрын

Caiden Zagala the gasket inside was so deteriorated that it fell apart when I tried to take it off. Had to clean the float needle of residue from the old gasket before installing the new one.

@caidenzagala7420

3 жыл бұрын

Well there was a bunch of gunk in my carb, just cleaned it really good

hey it was still caked with dirt on the outside!!!!!...lol....man that thing had to of been dirty after all that cleaning and still couldnt get it all off!!!

Audio cut out like 4 times

How to fix (rebuild) my choke 98

@Fixyourdirtbike

5 жыл бұрын

There isn't much to rebuild, its just a plunger and a fixed jet. What's the problem?

@furry_class6

5 жыл бұрын

@@Fixyourdirtbike can't start the bike and the choke is break one time and i dont know What to do to start in Hot time it's starting but when the time is cold he can't start

@Fixyourdirtbike

5 жыл бұрын

What did the choke plunger look like when you took it out?

@furry_class6

5 жыл бұрын

@@Fixyourdirtbike When you pull the sucker does not want to sit the paddle does not snap He's back in place

@Fixyourdirtbike

5 жыл бұрын

Have you removed the choke assembly to check for damage?

Yeah I don't eather the wife's little brother sent me a pic of it and was like what is this my bike won't run now so I pulled the carb off and check to see if it was a air fuel screw but it didn't go to nothing it's just a hole in the bowl that goes to nothing lol

@Fixyourdirtbike

8 жыл бұрын

+badnews300ex Is it in the bowl or around the rim where the seal sits?

The bowl

@Fixyourdirtbike

8 жыл бұрын

+badnews300ex Huh. If you can post a pic on www.FaceBook.com/FixYourDirtBike I could tell you. Like I said, all I can think is the drain, but it might not be the original carb either.

4:20 brass 😡😡😡😡😡😡