So my tech tip. The gold trans assembly lube works great for putting boots or hoses on. I work on a lot of diesels and use it to assemble the charge air cooler boots. Works great on coolant hoses as well. Doesn't affect rubber components like petroleum products

While putting the elbow on the intake tube I found putting my hand through the elbow and pushing out on the lip of the elbow helps it go over the tube a lot easier than working it from the outside. Hope this helps with the most difficult part of the install.

@fullaccessutv

Жыл бұрын

good idea. I will have to try that!

I like the plate and looks super clean! A true snorkel will accomplish the same thing for the dust plus get the belt exhaust higher however

@fullaccessutv

Жыл бұрын

Agreed, we just had no use for higher intakes blocking the rear view.

Took about 3 hours but yeah. Very nice looking. Thanks for all the videos and KRX supplies.

Looks easy enough. Guess I'll get one soon! Update, got it and installed it in a couple of hours. Looks great. Did the UNI filter at the same time. Now waiting for the rock sliders to come in.....

Thank you for sharing ✌️🇺🇲🙏

It would be nice to hear what it sounds like and see it tested. Thanks

@fullaccessutv

Жыл бұрын

There is noticeable sound difference from stock.

Good shit Jake!

How about a video of the new cage for the 4 passenger KRX, Jake? I know I’d like a stronger one than the factory uses, and yours looks so much better, too!

@fullaccessutv

Жыл бұрын

LOL. Call me at the shop. We have options

Have you done that on a KW Supercharged machine? I'm not sure how that would all fit right there, but I like the way that looks!

@fullaccessutv

Жыл бұрын

not yet, but i dont think it would interfere. I will have to look into that.

@amsoilron

Жыл бұрын

@@fullaccessutv expect a call from Froadn Fabrication tomorrow! We will adapt this to my Supercharged KRX 4.

What would make that elbow to go on a little easier. Is to take a heat gun to that elbow and make it a little softer and it’ll go on like butter

@fullaccessutv

Жыл бұрын

tried that. They just want to crush like a beer can. The only way is to fight it. It was better to put heat on the silicone boot.

Nothing for the CVT exhaust? What is the location/height of the exhaust? Just curious. Good video & looks like a good product.

@fullaccessutv

Жыл бұрын

we dont deal with deep mud and water on the west. For that or a CVT exhaust riser, a snorkel kit would be a better fit.

What are those vents in the curved part of the plastic?

@fullaccessutv

Жыл бұрын

those are CNC cut and powder coated caps to keep stuff out.

@atcdan133

Жыл бұрын

@@fullaccessutv I don’t mean on the snorkel part for the intakes. I mean down low in the bed like the curved part of the bed where the spare tire would go if you stored it there. It looks like you have some sort of vent there.

@fullaccessutv

Жыл бұрын

@@atcdan133 lol. OK now I know what you mean. Those were actually the first attempt at the vent delete. Unfortunately that spot sucked up too much dirt, and we’re not large enough so we got higher belt temps.

What is the rear extension that’s holding the cooler?

@fullaccessutv

Жыл бұрын

Custom rear bumpers. They’re in the other videos.

Definitely ordering one up. Watching the video I see a couple vents in the bed, did I miss a video?

@fullaccessutv

Жыл бұрын

those were the original delete kit. They didnt work out/

How much are they?

@fullaccessutv

Жыл бұрын

Link to them is in the description

What’s the good from this kit?

@fullaccessutv

Жыл бұрын

The main thing is looks. Couple little advantages, but getting rid of the ugly air intakes is a bonus. + less dust inhalation

@johngeary8534

Жыл бұрын

@@fullaccessutv went by the shop today, got to see the kraken in person!! That’s all I’ll say. Everyone was so friendly and took time from there busy day to answer all my questions!!! Great customer experience!!!

@fullaccessutv

Жыл бұрын

@@johngeary8534 Sorry I missed you. I must’ve been stuck doing paperwork lol.