Great stew Lance as always. It was good to recognise Rich Beeson and both he and his family appreciated it. The MF 20 does look very good on the bonnet. That is a good tip to connect the two batteries in parallel to recover the very flat one. Good luck.

@BundyBearsShed

21 күн бұрын

Thanks Peter, wait until you see what he is sending me, Im a bit excited about that one.

Nice looking boxes, at least in video, with those pallets, almost look like mine carts.

@BundyBearsShed

18 күн бұрын

We will have a big fire with the pallets one day, we get heaps of them in at QTS.

I know what you mean," My get up and go got up and went ". Take care. Cheers

@BundyBearsShed

21 күн бұрын

Yeah I dont like sitting about much.

G Day Lance, another great stew there, I'll be getting myself some of the CAV lapping compound for future use, your MF 20 bonnet's looking good but I know if I tried that with mine I would have nothing left lol it's great seeing blue sky again, we;re back to grey again today. many thanks Barry

@BundyBearsShed

21 күн бұрын

Thanks Barry ,we are having a rainy day today, up to 25mm apparently which will be good for the trees.

Hi Lance, I hope you don't mind, I told you last week about a pump on a David Brown 990 that was smoking after a pump reseal. We realised today that we hadn't bled the bottom bleeder on the cam advance mechanism . Did that, and the smoke instantly went!! Obviously, it is not advancing the pump cam. Another lesson learned.

@BundyBearsShed

18 күн бұрын

Well I had not thought of that myself, good work.

Great Stew Lance - certainly keeping yourself busy - the MF20 bonnet looks a treat, should look great along with the mudguards!

@BundyBearsShed

22 күн бұрын

Yes there is some work in it but nowhere near as much as a paint job.

Any day in the shop is a good day, when the weather is nice, its a great day! Thanks!

@BundyBearsShed

22 күн бұрын

That is for sure.

Lance if you run into the 'really' flat battery problem again with the CTEK battery charger, while you did really well by connecting it up in parallel with another battery, good move. But next time just put the CTEK in the 'Power Supply' mode for an hour or so, and then try it in the 'Normal' mode again, and finally when it's done with that and floating on Green, throw into Recondition' mode to give it a full wake up (if it's not already too badly hurt).

@BundyBearsShed

22 күн бұрын

ok thanks, I did try the power and rejuvenate but only for a few minutes and gave that away. It seems to have recovered well thankfully.

😊Well Thank you for the mention Lance,,I’m a happy man today,,Never thought I’d be on the Stew,,Every member of my family will be made to watch this several times 😂😂 Thanks again and hopefully the present will be with you soon friend 👍🤠🚜

@BundyBearsShed

22 күн бұрын

Happy to give you a shout out, I meant what I said we meet some great blokes through KZread. You could strap the family to the chairs with a load binder or two eh😂

@duncanrose3891

21 күн бұрын

Post up the 'beast' page plz fellas....

The mf 20 will look brill show queen's all looks the same when they have had there history taken away in place of a better then factory paint job but ha ho that's just my preference Lance 😂

@BundyBearsShed

22 күн бұрын

Mine too but I dont often get a chance to find one that hasn't had some sort of crap paint job over the years.

We just started our summer season in the states. Right now in the mid west the high tops out around 98 degrees f. With a heat index of 108.

@BundyBearsShed

18 күн бұрын

That should get the juices flowing.

About polishing, do not use a wax with silicone because it is difficult to put paint on top of it afterwards. C u next time 🇩🇰

@BundyBearsShed

22 күн бұрын

Yes I have been there before, it gets right in and even then I have had to use silicone drops in the paint.

@KP-nd3bx

22 күн бұрын

@@BundyBearsShed or a lot of thinner to wash the silicone away 😊

Lance you're obviously busy - but did I miss something, have you given up on the Mk2 65 ? Was looking forward to those epicyclic final drives! Stay well mate.

@BundyBearsShed

18 күн бұрын

No I hurt my knee and Dr told me to not do any heavy stuff for a while so Im trying not to do the final drives for a while. Im doing lighter work for a while.

@michaeluk2567

16 күн бұрын

Ahh thanks, yep, you gotta look after yourself first. Hope you’re on the mend.

I used to have one of those seats. They are good but if you leave the tops off the cans you can end up with a wet leg 🤣 pine here is much better than the stuff we used to get in the UK they grow it real fast there.

@BundyBearsShed

22 күн бұрын

I was thinking that may happen. lol.

There are sponge sanding blocks Lance. I wrap around them 😀 Did you try your angle strip discs yet?

@BundyBearsShed

22 күн бұрын

Yes the strip discs went ok. I find I do prefer the needle scaler on castings as it leaves the rougher texture. I have always just used the flip-flops for sanding. $9.95 and I get 4 to 6 blocks out of them, old habits I suppose.

@JACKATTACKED

22 күн бұрын

Whatever works 😀

Do you have a drawing for the seat adaptor on the 135?

@BundyBearsShed

22 күн бұрын

No it is a MF thing that came on the multipower 135 though.