Recommended! It works for me, thanks!

Just received mine and water mist doest not coming out at all. i thought they sent a faulty product.thank you for the video. just fix the rubber sealent . i take it out and put it back properly and firmly. now its working fantastic. thank you

@alex.k5057

2 жыл бұрын

Welcome. You need to becaful. The rubber sealant easy broken. I am trying find other rubber sealant to replace it.

@macytan5641

2 жыл бұрын

Mine doesn't have

Is works again. Thank you so much 😊

Terima kasih banyak-banyak, sangat2 berkesan, memang bergunalah video ni, thank you so much, syukrann2

@alex.k5057

2 жыл бұрын

Sama-sama☺️

thanks...your video help me a lot

Its works.. Thank you for good information..

Thank you much,the technique also worked for me.

It works! Thanks a lot!

Its working now found out that the connector is detached that is why its not working. Thank you!

Good. Thank you it works

Thank you 🙏🏼

Much appreciated for the tutorial video

Thank you so much,it worked,and the water came out more faster before this

@alex.k5057

2 жыл бұрын

Welcome

@jadetan1973

2 жыл бұрын

@@alex.k5057 Good day to you, my nano spray gun dropped on the ground can't functioning now 😭 The air the light is okay, but the motor can't suck the liquid out🤧

@alex.k5057

2 жыл бұрын

@@jadetan1973 please check your bottle got crack?

@jadetan1973

2 жыл бұрын

@@alex.k5057 Yes is crack, I tried your way to fixed it, can't functioning at all 🥺😭

@alex.k5057

2 жыл бұрын

@@jadetan1973 maybe you can try use glue to glue the crack place?

Mine not working water didn't come out through. Much same as yours. Gun are difference comparison. I will try fix up the press pipe later.

Thx mine spray now

Use a properly charger & liquid.. Can make your equipment lasting.

@alex.k5057

2 жыл бұрын

I not sure. Still study it.

yall can also check the bottle cap. mine got crack. seal the crack to maintain the pressure inside the bottle.

@yinpengsoh152

2 жыл бұрын

Please advise how to seal the crack ?

@ahmadsyahmi351

2 жыл бұрын

@@yinpengsoh152 these hacks should do the job. as it doesn't maintain high pressure but enough to provide suction effect. 1. 3 sec glue the crack 2. white tape n cable tie the bottle neck. 3. hot glue / 2 tonne glue to permanently secure the crack. let it dry before attach it to the spray gun. goodluck

@yinpengsoh152

2 жыл бұрын

@@ahmadsyahmi351 sorry, please advise how to glue

@ahmadsyahmi351

2 жыл бұрын

@@yinpengsoh152 you mix both hardener n resin together. plast it to the crack. then using a cable tie to tightenen it.

@ahmadsyahmi351

2 жыл бұрын

let it fullydry then try attach to the spraygun

Hi I Hope you can answer my question mine only squirt water after i turn it off. When i turn in on no water si coming out then if I turn it off water starts to come out. Thanks

@alex.k5057

2 жыл бұрын

Please try it like my video. Flashing it 1st. Sometime my 1 also like this problem.

How do you adjust the size of the mist spray?

@alex.k5057

2 жыл бұрын

This model can’t adjust

Alternative bottle that are suitable?

@alex.k5057

2 жыл бұрын

You can try other bottle

hello @alex.k! just got my k5 nano and no motor sound also.. but blue light lighting up. Any idea how to fix this? thanks! i tried charging it and same.

@alex.k5057

2 жыл бұрын

You can try check the wire from board to motor？

@gingerleenumayam1449

2 жыл бұрын

Same problem with mine...

@analisabona2498

2 жыл бұрын

Same

My spray gun is without blue light, can this be fix? Thank you.

@alex.k5057

2 жыл бұрын

Maybe led light burn out? Or board problem? Fix it you need to replace parts with soldering tools.

@angieng2112

2 жыл бұрын

@@alex.k5057 Sounds so complicated to fix it. The blue light issue found out upon receiving it. Will be returning to seller. Appreciate your quick response ya. Thank you.

What's the charge's color when charging or when fully charged ?

@alex.k5057

2 жыл бұрын

When charging is RED, Full Charging is Green

@elenakabugatan4402

2 жыл бұрын

Hi, is it working when it is charging?just red color but when I press the bottom its not working..tnx

@alex.k5057

2 жыл бұрын

@@elenakabugatan4402 my 1 when charging red colour still can working

Hello, I've pressed the hose and water came out but the spray is still not working, or can i send you the video of my spray gun problem to you?

@alex.k5057

2 жыл бұрын

Did you check your bottle rubber sealant? How u send to me the video?

@darylllopez3339

Жыл бұрын

@@alex.k5057 Hello what will I do if the rubber sealant is broken/ loose

@alex.k5057

Жыл бұрын

@@darylllopez3339 try to modify some rubber become that sealant. Because it did not sale spare parts

Hi Alex, I'm finding for Nozzle replazament, cause this device has broken in a home accident. Do you know somthing about that?

@alex.k5057

2 жыл бұрын

Sorry, this Nozzle dont have sale spare parts.

what to do if its not spraying like mist but the fluid just comes out in a straight line? its not spraying correctly

@alex.k5057

2 жыл бұрын

Not correctly. Spray out straight line will be more water.

I need help why is my K5 spraying like a water gun but not a mist?

@alex.k5057

2 жыл бұрын

please check the air hose

hi alex , my k6X mist is not fine(more like water droplet) any way to fix ?

@alex.k5057

2 жыл бұрын

Please check your air hose is ok? (Means I comment to press that hose)

@KingsleyJinKazama

2 жыл бұрын

@@alex.k5057 ok will try later thanks

Hi Alex, water came out only when I press the hose. If I don't press the hose, mist doesn't come out at all. Any way to fix it? Tq

@alex.k5057

2 жыл бұрын

Please check you press that hose got leaking at front? Has water come out means water line hose is ok. Mist doesn’t come out mostly is air hose line not enough air come out with water hose.

mine come with missing tube. i tried unused tube i found on my house but the circle things at the end of the tube, i not sure what it is. my spray machine not working

@alex.k5057

2 жыл бұрын

Please check your motor working or not 1st? Then check all tube connect? Then check bottle got crack? Then check bottle upper rubber seal is ok?

I squeezed the hose like you did but the water still come out weak.. what should I do?

@alex.k5057

Жыл бұрын

Check the bottle have close properly and the bottle upper rubber is good condition?

Hi, mine was blowing bubbles inside the bottle and not spraying

@alex.k5057

2 жыл бұрын

Means the air return back to bottle, maybe your bottle got crack or rubble seal not install properly? Or maybe front side head block the. The air return back to bottle got bubbles?

Hi may I know need how long to fully charge. Mine is K6X

@alex.k5057

2 жыл бұрын

i use not fast charging about 2 hours

@teohyj1795

2 жыл бұрын

@@alex.k5057 for K6X the light will become green if fully charge?

@alex.k5057

2 жыл бұрын

@@teohyj1795 mine is K5, the light will become green if fully charge

@teohyj1795

2 жыл бұрын

@@alex.k5057 ohh I see

mine do not make any sound. i think the motor is problem, can u help me sir. THANK YOU!

@gutennacht4318

2 жыл бұрын

i just buy this thing and never use it

@alex.k5057

2 жыл бұрын

May I know the purple light is ok when turn on?

@choosehandy657

2 жыл бұрын

hello @alex.k! just got my k5 nano and no motor sound also.. but blue light lighting up. Any idea how to fix this? thanks!

@alex.k5057

2 жыл бұрын

@@choosehandy657 please check wire to your motor and your motor 1st

I mean what kind of tools(or number of theirs any number) you used to unscrew..

@alex.k5057

2 жыл бұрын

Just a normal screwdriver (+)

@catharinequirimit4667

2 жыл бұрын

@@alex.k5057 OK but it seems too tiny holes. Thank you

Hi Alex what to do if the water is noy going up?

@alex.k5057

2 жыл бұрын

Please check your bottle and hose 1st

Is the UV light replaceable? If it is, how do you replace it?

@alex.k5057

2 жыл бұрын

I think can replace it. I havent do it before. Because I don’t have soldering tools.

Hi Alex, good day to you. I have checked and found that mine one is the hose keep dropping so only air coming out. After installing it probably still drop again for many times. May I know how to tighten it to avoid it drop again? Thank you!

@alex.k5057

2 жыл бұрын

You means the hose inside the bottle always drop?

@wongpakchen6191

2 жыл бұрын

@@alex.k5057 Yes. When connected it and spray 1 round then it drop again.

@wongpakchen6191

2 жыл бұрын

@@alex.k5057 the hose that connects the bottle of the hand sanitizer liquid. It keep dropping after 1 round of spray. Not sure how to tighten it although I have tried cable tight and rubber band.

@alex.k5057

2 жыл бұрын

@@wongpakchen6191 you can use some knife cut out abit at the plastic place, make it become got some rough line. But you need slow slow cut, don’t make the connect tube brake or broken. U understand?

@wongpakchen6191

2 жыл бұрын

@@alex.k5057 good morning Alex. You meant after cut a little bit short of the hose and to make the rough line is inside the hose correct? The rough line to make it not so easily to slip and slide down from the connection tube correct?

Can you use it on paper?

@alex.k5057

2 жыл бұрын

cant

sir, where to buy sprinkler for k5 nano spray? mine got broken😒

@alex.k5057

2 жыл бұрын

Please contact your seller

Why my k5 was leaking out from the hose head, then keep leaking when spray

@alex.k5057

2 жыл бұрын

The hose got crack?

@aresmatthew

2 жыл бұрын

K5 problem is the Hose Tip is Too Short, hence, the pipe will easily come out from the tip, you need to use a sand paper or tweezer to scratch little on the tip & then apply super glue & fix back the pipe & wait dry for one day, then, will be ok. Manufacturing Defects 😓😓😓

Olá tudo bem? Meu Nano Spray está saindo muita água, um jato muito forte (depois que tirei a borracha e coloquei de novo)

Hi sir... Mine is motor cannot stop running even turn off.... When on mode,all ok but when turn off motor still running but light already turn off.... Can u help sir??

@alex.k5057

2 жыл бұрын

Control board problem? Got contact your seller?

@asagiriasagi6243

2 жыл бұрын

Control board problem tu

Our bottle sealant is broken where can we buy a replacement?

@alex.k5057

2 жыл бұрын

Sorry. I also have finding any spare parts. This don’t have any spare parts sale. You just can modify it with other sealant.

Hello mine is working but its spray is like water gun.i expect it to be like nano mist spray what will i do?

@alex.k5057

2 жыл бұрын

You may try to press hose like me. Some times the air hose stucked, then water hose will come out more water.

I need help for my hydrafacial

@alex.k5057

2 жыл бұрын

Yes?

Ano ginamit nyo po pangtanggak ng screws

@alex.k5057

2 жыл бұрын

Sorry, can u write in english? 😊

Mine got no sound and no water coming out. Is the motor spoilt in this case ? Seller said press 2-3 minutes also still the same.

@alex.k5057

2 жыл бұрын

Have light?

@rosalindlee8806

2 жыл бұрын

Yes got nano light

@rosalindlee8806

2 жыл бұрын

Just newly bought from shopee.

@alex.k5057

2 жыл бұрын

@@rosalindlee8806 should be motor problem, contact shopee warranty

@rosalindlee8806

2 жыл бұрын

@@alex.k5057 ok thank you

Te pasa que no absorbe el agua? Al contrario la expulsa y hace burbujas

I'm scared that I might destroy it haha

Solution is coming out from the nozzle instead of fog . How to fix it?

@alex.k5057

2 жыл бұрын

Sorry I don’t understand

after charging the device, it cannot power on anymore. any idea?

@alex.k5057

2 жыл бұрын

This you need contact your seller. Mostly is board problem or battery problem. When you continue charging. Got charge light on?

@tehzibin1368

2 жыл бұрын

@@alex.k5057 hi, I got the same problem.i charge the machine it direct show green light.however after unplug cannot function

@alex.k5057

2 жыл бұрын

@@tehzibin1368 motherboard problem I think.

@rusaimiamira4962

2 жыл бұрын

at first it was red lighr, but then after a few second it already turns green.

@alex.k5057

2 жыл бұрын

@@rusaimiamira4962 please contact your seller or make warranty. Don’t always try charging. Later battery burn off.

My unit doesn’t work. Tried charging it for half day, still no light, no nothing.

@alex.k5057

2 жыл бұрын

when charging got red light? if got red light, mostly is battery problem. if not light motherboard problem.

Mine is really loud when using and no water at all just air, tried all of your techniques but didnt work at all 😫😫

@alex.k5057

2 жыл бұрын

Please check bottle oil seal?

@chaisoe

2 жыл бұрын

Yes i did, but it still doesn't work, i did everything in your video, its not even sucking water in the bottle not a little bit

@alex.k5057

2 жыл бұрын

@@chaisoe like this final is contact your seller

@hoangthienannguyen7693

Жыл бұрын

Same mine, not even sucking water

So we put plain water?

@alex.k5057

9 ай бұрын

when u test is better you use plain water

@diane007

6 ай бұрын

Thanks dear 😊

I applied all the solutions but still not spraying but only air comes out

@alex.k5057

2 жыл бұрын

Please check hose at bottle side has come out?

my gun spray out like water instead of nano , is this can be fix?

@alex.k5057

2 жыл бұрын

It is model K5? Or other products? Some of spray gun spray out many water. If K5, maybe got block at air hose or front side? Please try press the air hose let water refresh inside hose and head hole.

@bojio4569

2 жыл бұрын

@@alex.k5057 is K5 model, will try press the air hose let water refresh inside hose and head hole ~ do u know is there any fake K5 or no? If yes, do you know how to check original or not?

@alex.k5057

2 жыл бұрын

@@bojio4569 At market too many fake K5. I think maybe original 1 is the words "Nano Spray Machine K5" is Print in body and no the sticker 1. My 1 I think is Fake. Because is sticker 1. I still finding original 1.

@bojio4569

2 жыл бұрын

@@alex.k5057 i din try out press the air hose let water refresh inside hose and head hole, i go and replace another gun from the shop. Now the new gun want to turn on , need to press and hold the power button 2 seconds only can turn on. The words "Nano Spray Machine K5" is printed in body.

@alex.k5057

2 жыл бұрын

@@bojio4569 woh! Like this maybe is original? Where u buy ? Can let me know? And how much is it?

Is this steam

@alex.k5057

Жыл бұрын

No steam sir

the machine quite

i just discovered that mine doesn't have water sealant:(

@alex.k5057

2 жыл бұрын

Try find O-ring at hardware shop?

Nano machine not hot water ??

@alex.k5057

Жыл бұрын

no hot water

Just buy come back no working

Lousy product

@alex.k5057

2 жыл бұрын

Many problem right