Can this be used on metal?

@Geeksmithing

4 жыл бұрын

That is a simple question with a complicated answer. While you cannot directly engrave or cut metals, there are still ways you can use the laser along with metals in your projects. The laser can remove surface coatings on metals such as powdercoating or anodization. This allows you to engrave stainless steel tumblers and water bottles, as it is actually just engraving/removing the paint coating, letting the steel color show through. You could also spray paint the metals and then laser away a design into the paint revealing bare metal making a mask/resist layer. Then use an salt water/electric setup etching setup to engrave/etch into the metal where your paint was removed. Remove the paint using acetone. You are left with an accurately etched surface. If you still want to get a laser to engrave metals, you should look into "fiber lasers", but be prepared to spend at least $3000.

@TheFalconJetDriver

4 жыл бұрын

Geeksmithing thanks for taking the time to answer his question your answered a question I had. And subscribed!😁🛫

@marckleejoseph2498

4 жыл бұрын

Hi. Thx for thw video. I liked. At least we can engraving on stainless steel?

@Geeksmithing

4 жыл бұрын

@@marckleejoseph2498 nope.

@leedozza3435

4 жыл бұрын

Hi mate whats the largest size material you can engrave? Thanks mate

I’ve had one of these for 2 years. Played with it for a month and gave up because of the software and lack of knowledge base. This has inspired me to give it another go. Thank you very much. Subscribed 🏴󠁧󠁢󠁥󠁮󠁧󠁿

@Geeksmithing

5 жыл бұрын

Oh wow. That is the best compliment I could receive! Thank you! Reach out if you get stuck again! We are in this together!

The most common question I get is about the rotary module shown in the video. I finally made a video on how to make your own! kzread.info/dash/bejne/eYN6ktdyodasf6w.html

@carlosherrera5624

4 жыл бұрын

does it cut glass or plastic ?

@Geeksmithing

4 жыл бұрын

@@carlosherrera5624 it does cut cast acrylic perfectly. I am not sure about glass. I doubt it.

@carlosherrera5624

4 жыл бұрын

Thank you

@musicilla

4 жыл бұрын

Goodmorning I was wondering is there a depth adjustment for the laser? Say if u wanted to laser 0.2mm stainless would it burn through it ??

@Geeksmithing

4 жыл бұрын

@@musicilla you cannot cut or engrave metals with this, so.. um.. no. 🤷‍♂️🤓

Sold me. I am getting one. Just downloaded the software you recommended so I'll get a jump on it before the unit arrives. Thanks for posting great content!

@Geeksmithing

4 жыл бұрын

Oh sweet! Happy to help! Feel free to reach out if you run into a snag!

@domenicdesantis9847

4 жыл бұрын

the one u have is a Mophorn or Orion??

Great video Wes; I bought one last year on your advice and it’s already paid for itself twice over. It allows me to personalize hand crafted items. Thumbs up.

@Geeksmithing

5 жыл бұрын

Woo hoo! That's great to hear!!

@guitrgirl

2 жыл бұрын

Can you engrave on glass as well?

K40 might be on my short list of tools to add to my shop. Will be nice for details and logos and such on my CNC furniture. Also, great vid! Glad to see you putting stuff out there again!

@Geeksmithing

5 жыл бұрын

Hey! It absolutely should be! I have been constantly impressed with it . Thanks, I have been wanting to put this video out for a long while! I hope to put vids out more regularly.

I subscribed after watching this. I like how you get to the point and tell us just what we need to know. Great video.

@Geeksmithing

5 жыл бұрын

Thanks Ken!! Cheers!!

@markh2128

5 жыл бұрын

I am also now subscribed for same reason! Also your a smartass and I respect That. Say it like it is, in a world full unicorns and snowflakes I like to hear its great or POS. Keep them vids coming.

@Geeksmithing

5 жыл бұрын

@@markh2128 haha, thanks for the sub! Hope you like some of my other videos. 😄

@_M317

5 жыл бұрын

I just did the same. Great video and can't wait to see more about the K40

@Geeksmithing

5 жыл бұрын

@@_M317 cheers!

many thanks for this intro video. I've just bought one 2nd hand and finally switched it on 12 months later without a clue of what to do!. Great overview to get me started. Thank you

@Geeksmithing

4 жыл бұрын

Oh wow! Congrats! That's a big first step! Good luck!!!

Answered every single one of my questions & doubts! Well done video! Thank you.

@Geeksmithing

3 жыл бұрын

Thanks! Happy to help!

4:11 I like how the red highlighted squares are actually transformed to perspective rather than just a flat square nice work

@Geeksmithing

4 жыл бұрын

Thanks for noticing that!:) Cheers.

@GetRealwithMike

4 жыл бұрын

That impressed me as well. If you took the time to get that right, then I have a lot of confidence in what you said in your video.

You, sir, just sold me on a 400 dollar laser engraver. Excellent review! Also, I just subbed. Thanks!

@Geeksmithing

5 жыл бұрын

Hey, thank you sir! Happy to help. I have had mine for over a year now and it's still going strong! Thanks for the sub, let me know if you like any other videos:)

@pyrexphainz431

3 жыл бұрын

Is there a tool or setup that comes with it to do silicone bracelets

An honest and useful review, not seen one of those on KZread for a long time! I’ll finally be picking one of these up now

@Geeksmithing

5 жыл бұрын

Hey thanks! I like to think it helps! Hit me up with any questions!

Well done, informative video. Thanks for taking the time to record and post.

@Geeksmithing

4 жыл бұрын

Thanks! Happy to help! Thanks for stopping thru!

Great review, great advice and awesome intro!

@Geeksmithing

5 жыл бұрын

Hey thanks Steve! I figured true Nintendo fans would dig it!!! :)

Awesome Wes, super helpful for a lot of folks. Those mugs are dope

Thank you for this I’ve been procrastinating for more than a year about this....

I've been looking to pull the trigger on one of these for about a year now.. Great write-up. Subscribed.

@Geeksmithing

5 жыл бұрын

Oh awesome! Thanks I appreciate that! Welcome aboard! 🚀

Great job on this review. I have mine for almost a year now. Burned out my first laser tube by over powering it. Then I upgraded to a 60W tube. Loving it.

@samirpasic6836

5 жыл бұрын

Where you order 60W tube,how much,is it hard to instal??? If you have link please give us. Thank you very much

You just gave me more to think about. I've been heavily looking and almost ready to make a decision on which of these machines to go with. The fear of not getting the added worth to my shop has made it really hard to pull thousands of dollars for a glowforge or other machine of that nature especially with me transitioning out of the military.

@Geeksmithing

4 жыл бұрын

That is exactly the same thought process I went thru. I figured that $350 was an acceptable amount to toss at the idea of a K40... I figured even if it didn't work out, I could use the parts for something else... But now that they are also available on Amazon in addition to eBay, the consumer has additional protections/options if something doesn't work.

Thank you for all the information! I was trying to figure out what to buy, and I think I will be buying one of these in the near future. I will be watching more of your videos too!

@Geeksmithing

4 жыл бұрын

Thanks!! I appreciate it! Glad it could be of help to you 😊!

Thanks for the info I did not know they had come down in price this far.

You have now got me interested in buying one. Can’t justify thousands, but this seems a good alternative.

@Geeksmithing

5 жыл бұрын

Sweet! It's a fun bit of kit!

I have had one for almost 3 years. Had to replace the laser power supply after only 2 months, warranty took care of that. Had to replace laser tube after about 6 months. I paid for that. Installed a real air nozzle system. Got rid of the clamping system and put in an aluminum grid for a bed. Built my own rotary device. Working good now.

@z8ty

5 жыл бұрын

I hope you see this... Do you have time to share more about your air nozzle system, the clamping system and your rotary device? I assume for the clamping you the bed you put in has tapped holes spaced at regular even intervals. Ready to buy one of these, but would like to learn as much as I can. The rotary device would be a must have, but the once I saw on Amazon were close to $200.00.

Great review, I have been wanting one of these for a while now thanks.

@Geeksmithing

4 жыл бұрын

My pleasure! Feel free to reach out if you have any questions!

Great video, thanks for sharing your experience!

just stumbled across your channel as i am looking to get a k40 within a month or so. didnt even know you could get the rotary part so i am very much looking forward to seeing a video on that.thank you for taking the time to make videos to help us all. Subscribed!

@Geeksmithing

5 жыл бұрын

Glad to help! Thanks for the support! 🤜💥🤛

@Geeksmithing

4 жыл бұрын

Rotary vid is coming this week!

@Geeksmithing

4 жыл бұрын

Rotary Video!! kzread.info/dash/bejne/eYN6ktdyodasf6w.html

Not that you're unaware of this- but, that was a damn fine video. Thanks. Well done!

@Geeksmithing

5 жыл бұрын

Ha!! Hey thanks!! I appreciate it!

Man thank you for the video! I do want to dabble in budget laser engraver but have not wanted to put the time in for the Gamble. This video answered all my questions and examples are more than respectable I do believe I'll be buying one in the next month. Thanks again!

@Geeksmithing

5 жыл бұрын

Oh nice!! Happy to help! Feel free to hit me up with any questions!

I've taken your advice. just ordered one. like you, a laser has been on my list for a while and the price point on these feels reasonable for me to dip a toe in the water and see what they can do for me. Looking forward to giving it a whirl. Thanks for the video

@Geeksmithing

5 жыл бұрын

Yes!! Hit me up if you have any questions!

Great content thank you for posting !

I use various £50,000+ units at work and to be honest apart from a lot of QOL features the etching on yours seems to be on par with what the systems I use can do. Cool video!

@Geeksmithing

5 жыл бұрын

Oh neat! That's interesting! Thanks for checking it out. Please stick around and enjoy some of my other projects!:)

Went to a Sign show last year and YEA put the need in place of the want:) Hopefully I can get into this sooner than later. Thanks for the great video.

@Geeksmithing

5 жыл бұрын

My pleasure! Thanks for watching!

Thanks for the candid and educational video. Very forthright. Great job! 👍

@Geeksmithing

5 жыл бұрын

Thanks, I appreciate that! 🤓

Awesome! I can't wait for the follow up videos!!! 😀

I've had a K40 for several years now and love it. I have done several upgrades however. I replaced the board with a cohesion 3d board ( I think it is based on the smoothie board but is sized to fit perfectly in the K40) . The board was only $100 and was the best upgrade I think you can do. I also made an electric water chiller from an Igloo ice machine ($90) and a temperature controlled outlet( made for a few dollars). The water chiller has worked great for 2 years now. I also added a motorized Z bed and air assist. All in all I probably have about $800 into it (including the laser itself) but now have a great machine that can hold it's own against much more expensive machines. The only issue I have now is the size (300mm X200mm). I think that the K40 is a great buy with a few accessories.

@Geeksmithing

5 жыл бұрын

Thanks for your thoughts on the K40. I also have a Cohesion board, but have yet to install it. Looking forward to messing with that soon. Cheers!

@shadowofpalms

5 жыл бұрын

@@Geeksmithing I think you will be very pleased with the Cohesion once you install it. I use laserWeb with mine and love it. Thanks for a great video and good luck with the new board.

We’ve had one for about two years no issues. Kinda hard to use but work good

Love your video and the cheeky tone. I got my machine a couple of weeks ago from a company supposed to be in Australia. I am in Australia, I am glad you got an instruction manual because even if it is only stapled it looks like it has some info. Mine was sleekly printed but only two pages an not much on it.

@Geeksmithing

2 жыл бұрын

Thanks for watching! Best of luck to ya!👍

FANTASTIC video!

@Geeksmithing

5 жыл бұрын

Oh wow. Thanks man! High praise!!✋

I like that the free software really is Free Software, that's my style :D

@Geeksmithing

4 жыл бұрын

Heck yeah!🤑😎

@hirenei

4 жыл бұрын

What's it called

@psider1522

4 жыл бұрын

@@hirenei Inkscape (for creating and manipulating vector files) and K40 Whisperer (laser control) are both Free Software and shown in this video.

@court2379

2 жыл бұрын

But is it worth your time to use the free stuff, vs buying lightburn for instance?

GREAT video. i make glass blocks and was wondering how this would work on glass? One of the first You tube videos that the person responds to most questions. way to go. thank you again

@Geeksmithing

5 жыл бұрын

Hey! Cheers! I appreciate that! I am pretty sure you can engrave glass with it but I believe you should be careful as to not engrave glass with lead in it, from what I read... I haven't tried glass yet myself but it is on the list of materials I am going to go over on a materials test video coming up soon! :)

Thanks for the very informative and also hilarious overview. Very helpful!

@Geeksmithing

5 жыл бұрын

Hey thanks! I appreciate that! Happy to help!!

Nice Video Wes! I am asked about this all the time at my make space, With your permission I think I would like to link this video onto our Wiki page.

@Geeksmithing

5 жыл бұрын

That would be amazing and I'd be honored! Thanks!!

Cool, thanks 🙏 for your brief introduction into this engraver, I have looked at them over and over again thinking should I take the plunge? After your introduction to them, I think I will have to invest in one of them, thank you very much for your information as it’s been informative enough for me, keep up the good work and I look forward to your further videos.

@Geeksmithing

5 жыл бұрын

Hey, absolutely! Thanks for checking out the video! I hope to release more soon. Best of luck with your new laser adventure. 😎

Thanks for this video, very informative! 🙏 I really would like to get one, but was nervous. I will go ahead now 🙂

That looks a lot better than I expected when I saw the boatload of those being sold on eBay a year or two back, complete with confidence-inspiring photos. I was at least expecting an upgrade money-pit, but that doesn't look like it even needs the upgrades I'd likely do.

@Geeksmithing

5 жыл бұрын

Honestly, the few really necessary upgrades are pretty inexpensive...even better if you happen to have or have access to a 3D printer!

You've basically answered my primary questions perfectly. Massively increased my confidence on pulling the trigger on a K40 soonish. It was also cool to see the water bottle I won from the Making Geeks survey in the video :D at least I know what high quality is possible. My main question outstanding is about the controllers and how to identify what type is in a low cost machine? Does it matter? FB groups seem to harp on about them but I guess it's just if whisperer is compatible with it.

@Geeksmithing

5 жыл бұрын

That's a great question. The K40 has a list of compatible boards and ways to identify them I believe.... I picked up a Cohesion3d controller board replacement for it and hope to swap it in soon, so that's also an option for you down the road a bit.

@fluffhead7892

5 жыл бұрын

I don't think you can know exactly what you're gonna get from the listing. But once you get it you can see your control board and it will come with CoralLaser/CoralDraw software. Had one almost a year and have used it probably 500+ hours (daily) and it does anything you really want to do with it but out of the box it needs upgrades and it needs constant maintenance (I use it a lot so obviously a lot for me).

Maybe on the next one show us how to run the machine, how to find origin, set z height etc.

@Geeksmithing

5 жыл бұрын

great ideas! Thanks!

Nicely presented and informative. Thanks for your time making the video.

@Geeksmithing

5 жыл бұрын

I appreciate the nice comment! Please enjoy another video while you are here!:) Cheers!

I did not see if it was included the cutting size. I appreciate the info, your video was very helpful

@Geeksmithing

5 жыл бұрын

Hi! The max cutting area is 9" x 14" of you remove the default clamping bed as seen in video

If I remember correctly, these were anywhere from $1k - $2k only a couple of years ago. Nice to see the price come down. I may bite.

@Geeksmithing

4 жыл бұрын

🎣🤓

Great Job! I need one of these to add to my channel! Just don't know how I'm going to sneak it past the wife. The box is pretty big! :)

@Geeksmithing

5 жыл бұрын

Haha! Just drape a frilly tablecloth over it. She will never notice!

Thank you! Bought a business over a year ago that has 2 x 100, 1 x 60 and 1 x 40 laser. Steeeep learning curve for me as learning everything from scratch. I haven't even touched the 60 and 40 as yet as I have no program/driver for them and the forums send me in 100 directions to get one. Thanks for the heads up on those programs.

@Geeksmithing

5 жыл бұрын

Oh wow. What kinds of things do you make? Glad to help!

@jaybursle5905

5 жыл бұрын

Personalised puzzles, assorted trinket boxes, toys, promotional key trags and magnets. Check our redearthtoys.com

Watched this video again Wes! Very helpful. *Thank you!*

@Geeksmithing

3 жыл бұрын

You bet dude! #teamK40 😆

My family has been in the sign and engraving business since the 70's. I worked there for a couple years but my asshole uncle took over and I had to bail to avoid shoving his head under the heat press. I was are laser engraving tech. I miss the Convenience of having one of these around to use. I didnt know these ones were so cheap. Adding this to my watch list on ebay and subbing to see how this thing works out for you. Thanks for sharing.

@Geeksmithing

5 жыл бұрын

I have had it about a year now, and it is still going strong. I hope to make more videos about it in the very near future. Thanks for the sub :)

Looking forword to you posting a video about the rotary module :) Thx

@Geeksmithing

5 жыл бұрын

It has been a popular request!:)

@willharris342

5 жыл бұрын

Geeksmithing I would like to see your installation and use process the eBay listings I see say it can’t be added to this smaller machine. I’d also like to see a link for the one you have as well. Awesome video you have me talked into buying one. Now for the wife!

@Geeksmithing

4 жыл бұрын

The rotary video is coming out this week!

@Geeksmithing

4 жыл бұрын

Rotary Video!! kzread.info/dash/bejne/eYN6ktdyodasf6w.html

Hey Man, thanks for this really informative and helpful... really appreciate you doing this

@Geeksmithing

5 жыл бұрын

You bet! Happy to help!!

well, that was a very honest and accurate appraisal. I'm researching Laser Engravers with a interest to buy, I will use your vidio as the benchmark to judge all others against. Thanks for sharing - subbed 👍

@Geeksmithing

5 жыл бұрын

Oh wow! That is some high praise and I think you for it! Please enjoy some of my other non-laser related videos ... and if you end up snagging one, hit me up with any questions you might have! Thanks! :)

@gordonchapman222

5 жыл бұрын

will do ✔

Great stuff, thanks for posting this! A couple of other suggestions I've heard that make sense is one, try to buy from a US seller, as if there's a problem they're usually a lot easier to work with than someone overseas. And second, make sure it is WELL VENTED to the outside, a lot of the stuff you engrave with the laser give off extremely toxic fumes you do not want to breath!

@Geeksmithing

4 жыл бұрын

Well the toxic fume thing can be a bit more serious than that, depending on what you are trying to laser. No one should laser any vinyl or anything with ABS in it, as it can create chlorine gas, that can corrode the internals of the machine and the internals of human lungs. Stick to organics such as wood, paper and cloth, and it's not really that serious.

@Geeksmithing

4 жыл бұрын

Good tips with the US seller bit

@leematthews3578

4 жыл бұрын

Andrew Tornadoboy , could this be used to cut thin balsa wood?

@Geeksmithing

4 жыл бұрын

@@leematthews3578 like butter

I’m not sure how I ended up watching this video, seeing that I’ve never done anything with lasers, but I enjoyed it very much. Now I feel like I need a laser engraver.

@Geeksmithing

5 жыл бұрын

Haha, well I am glad you are here! Please pull up a chair and enjoy some of my other videos! I would love to know what you think. :) And who can resist lasers?!

@Chrisamic

5 жыл бұрын

*Everyone* needs a laser engraver.

Awesome! thanks! I was on the fence about getting one! Sold!

@Geeksmithing

5 жыл бұрын

Woo hoo! ONE OF US!! ONE OF US!! Hit me up if you have any questions!

Thanks for the help Wes!

@Geeksmithing

5 жыл бұрын

You bet Jim!

This is great! I saw the Glowforge but 4 grand is a bit too rich for me. Especially considering I'm not going to be using it for income.

Great video. I've had one for about 4 years, although I never got mine working at all out of the box. Make sure you check all the wiring before turning it on, mine was a major fire risk the way it had been done in china. The earth wasnt even connected, and the high voltage cable to the laser tube was far too thin and poorly insulated. I upgraded to a DSP, added a larger tube, new PSU and a new focal lens and it's a very capable little machine now. Oh.. and I too am interested in that rotary bed. Great idea! Were those flasks you showed actually engraved with yours!!?? Brilliant results!

@Geeksmithing

5 жыл бұрын

I think they have improved some since then, but you are right, since they are coming from different manufacturers, people may get different results. The rotary was indeed used with this machine and made the examples I showed. Hopefully within the next month or so I can finally get to the video for that. Thanks for your interest and watching!

@thewarthogproject

5 жыл бұрын

@@Geeksmithing thanks for the reply! Looks like I'm gonna buy me some cups! Subscribed!

@Geeksmithing

5 жыл бұрын

@@thewarthogproject of your K40 dimensions are similar to mine, I had to modify my K40(i.e. cut the bottom out) to fit in tumblers to keep surface of item within focus.

@Geeksmithing

4 жыл бұрын

Rotary Video!! kzread.info/dash/bejne/eYN6ktdyodasf6w.html

Great video! Great explanations and spot on with visual aids! Thank you!

@Geeksmithing

4 жыл бұрын

Cheers! I appreciate it!

THANK YOU SO MUCH!! for making this video. Im definatley gonna follow you!!!

@Geeksmithing

4 жыл бұрын

😁 Hey thanks!! I'm glad it helped!! Hope you find some more videos you enjoy!

Love your Surge protector!

@Geeksmithing

5 жыл бұрын

THANK YOU!! Finally someone did! 😂

I bought the upgrades that you suggested in the description but I'm lost in how your hooking them up can you do a quick video?

very INFORMATIVE VIDEO AND LEVIATED SOME ANXIETY OVER THIS LASERR I WAS HAVING. tHANKS FOR THE SOURCCE LINKS. when I ADD THIS TO MY SHOP TO SUPPLEMENT MY sHOPbOT dESKTOP cnc LOOKING FOR TOW MERGING THEIR CAPABILITIES AND WATCHING FUTURE VIDEOS

Thank you , Excellent video very informative, no clutter and straight to the point. Liked and subscribed!

@Geeksmithing

2 жыл бұрын

Hey I appreciate that!! Thanks!! 🙏

Freekkin lazers!!! Sorry it had to be done.

@Geeksmithing

5 жыл бұрын

Dang! I should have had that in there!!

The weird format paper manual was most likely A4 size, as used in every country in the world...except the USA

@Geeksmithing

4 жыл бұрын

It was a deadpan joke. :P Sorry.

@internettrihard2955

3 жыл бұрын

@Bingus McDrangus Murica fuk yea

Thank you! Was contemplating the idea of buying one 🤭

@Geeksmithing

4 жыл бұрын

Do it! (I won't tell) 😉

The gateway drug for lasers :-) The K40 is how I got started a few years ago. K40 Whisperer and a raft of innovations and safety upgrades came over time. (There's a super Google+ group out there - but Google is killing the app so it's moving to a proper Discourse forum.) If you have the space, jump straight to a 60 or 100W with motorized Z-axis, not much more than you'll end up spending getting the K40 safe and tweaked and so much more in terms of capability. (Then get the Glowforge, Epilog or Trotec) The K40 leads you down the path to serious "laser all things" :-)

Can you please make a video of it cutting 3-4mm clear acrylic (plexiglass) sheet? Can it do in one pass without melting the edges?

@freeaudiobooks7469

5 жыл бұрын

Yes, you have to turn down the power of it

Seems better then some of the others that I've decided not to buy. Thanks for great video and the honest heads up about the unit.

@Geeksmithing

4 жыл бұрын

Happy to help!

Thanks for the video. It was a great product review!

@Geeksmithing

5 жыл бұрын

Cheers!

Hi Where did you find the system to rotate the object and how did you synchronize it with the laser? Thanks for the reply

@Geeksmithing

5 жыл бұрын

Hi! The rotary device I threw together from some parts I had around the workshop and a 3d printer. On the machine there is a stepper motor that cause the laser head to move left/right (X-Axis) and one that causes it to move forward/back (Y-Axis). All you do is unplug the Y Axis motor and plugin the rotary in it's place. So when the machine thinks it's moving the laser head forward and back, it is really just spinning the bottle forward and back beneath it. Hope that makes sense! This has been my #1 question on this video and I really need to make a video showing the rotary in more detail. Thanks for the kick in the rear I needed for that to happen. 😂😁🤓 Have a great day!

@abdelhaditaya880

5 жыл бұрын

@@Geeksmithing please do that. That's the first question i had when i saw it

@danio1021

5 жыл бұрын

@@Geeksmithing That's a brilliant solution :D

@Geeksmithing

4 жыл бұрын

Rotary Video!! kzread.info/dash/bejne/eYN6ktdyodasf6w.html

You really sold me on this one! But I have a question!!! Where can I buy the Rotatory Accessory for mugs! That's dope! Thank you! Loved the review

@Geeksmithing

5 жыл бұрын

Ha! I actually made it myself, with some bits and bobs from the shop and a 3d printer. I hope to make a video covering this very soon! Stay tuned!!:). Thanks for watching!🤓

@Geeksmithing

4 жыл бұрын

Just an update... that rotary video is on my channel now, feel free to check it out!

Ah crap, another KZread rabbit hole to fall down. Seriously though, great summary of what these machines are capable of. I had looked at them in the past and always assumed they were junk. While I have to pay for my Black Friday shopping spree first, this may have to be a Christmas gift to me. Thanks for the overview.

@Geeksmithing

4 жыл бұрын

Hey thanks!! I had a similar outlook on them for years(apparently their build quality was even more suspect back then...) But I figured for just over $300, it was worth a shop, worst comes to worst, I have parts to make a CNC machine or killer 🤖! 😆

Thanks very much for this video. I'm a teacher and found out our school had a been given an Emblaser 2 that no one knew how to use so I've been investigating its use this summer and I'm really interested in getting a laser cutter of my own. The K40 looks like it might be an affordable option. Thanks again from an absolute novice.

@Geeksmithing

4 жыл бұрын

Ah very cool! Feel free to reach out with any questions. Happy to help!

It would be nice to engrave cell phones on the back, could be a market for it like at a mall booth or something.

Who would win in a fight He-man or the crazy Optic laser kitty?

@Geeksmithing

5 жыл бұрын

Or the Surge Protector?🤔

While writing my comment I just realized you must have a 40 watt version, when I bought mine it was advertised as 60 watts, the lase tube looks to be identical to yours, so that tells me that mine is only 40 watts as well. Once again great video, straight to the point without the b.s.

@Geeksmithing

4 жыл бұрын

I appreciate the kind words! Cheers!

Nice positive reviews. I wish I had the room for one.

"That someone in China made specifically for me, that's nice... Just throw that out" lawl

The one big thing my father did to his was add in safety switches so if any of the lids on the machine are opened it kills power to the laser so there is 0 chances of the beam firing up while your working on it. He said he rather be paranoid than a paranoid blind man.

@Geeksmithing

5 жыл бұрын

It's absolutely a great idea, and on my list of upgrades. I have the parts, just haven't yet... Thanks for the motivation to make it sooner than later!

I love how the ad before the video of a $400 laser engraver was for a $3000 Glowforge.

@Geeksmithing

5 жыл бұрын

Haha are you serious? If you can snag a screenshot of that and send it to me, that would make my day! Heck, I'd send you a Geeksmithing tshirt upon receipt of that bounty!!😁

I'm glad you made this, thank you

@Geeksmithing

3 жыл бұрын

Glad I could help! :) Cheers!

5:50 What no "firein' ma' lazar" gif when you say "firing your laser"?

@Geeksmithing

5 жыл бұрын

Hahhaha. I totally said that when testing it when I first got it!!

I think if you are a person considering getting one of these, it is important to note that it can be a gamble. You may get a great (as great as it can be anyway) machine, or you may get a machine that needs all kinds of work to make usable. Quality Control is not a thing in the factories these come from. Good idea to have someone familiar with these types of things available to help you out, if you yourself are not.

@Geeksmithing

5 жыл бұрын

Excellent points!

Really enjoyed this guy's laid back attitude. 😆

@Geeksmithing

4 жыл бұрын

Thanks! 😊. I was trying to convey a sense of being genuine and honest with my opinion on the matter. 🙃

Love the video. Thinking of getting one myself. For your next video could you include slate as one of your tested materials? Great Job!

@Geeksmithing

5 жыл бұрын

Thanks!! And absolutely, it's on the list believe it or not!!:)

can this laser cut through thin plastic / wood .. say 3mm to 5mm thick ??

@Geeksmithing

4 жыл бұрын

Absolutely. Up to 6mm wood, acrylic, cardboard, plastics (as long as they don't have vinyl in them as that is dangerous to laser)

@chmarr

4 жыл бұрын

@@Geeksmithing absolutely AWESOME. now i know what i'm buying :D :D

@Geeksmithing

4 жыл бұрын

@@chmarr 😊 Those items and thivknesses, are what this machine really shines at cutting and engraving. Let me know if you have any more questions!

Any chance you have a link to the rotary piece you added?

@Geeksmithing

5 жыл бұрын

Sorry, no, I built it using parts I had on hand. I will upload a video on how to make one/ where to buy one very soon.

@freqster

5 жыл бұрын

There are lots of videos on how to make a rotary device yourself. Just a quick search and you willl get tons of results.

@13johncobb

5 жыл бұрын

Awesome thanks! Sorry just assumed it was an add on.

@Geeksmithing

4 жыл бұрын

Rotary Video!! kzread.info/dash/bejne/eYN6ktdyodasf6w.html

Thanks Geeksmithing, just what I needed to see. Now to spend money...

@Geeksmithing

5 жыл бұрын

that's always the trick, isn't it? :)

Very informative. I've actually been in the market for a later engraver myself. I'll have to give this one a look. War Eagle!

@Geeksmithing

5 жыл бұрын

Hahahah. War Eagle. Nice! 🤣

I thought that tube with the chinese writing was some hemorrhoid cream to ease the deal with all the troubles this machine gives you?

@Geeksmithing

5 жыл бұрын

Haha, I have not run into any issues but it may be of use for the sore Corel users that didn't like me tossing out their software. 😂😉😋

@GeekBuildersNet

5 жыл бұрын

**Best Comment**

Buy it and end up throwing half of it in the trash 😂

Thanks for the great review. I have been looking for a decent unit and this might just be the one. Subbed as well.

@Geeksmithing

4 жыл бұрын

Cheers! Hope you find more videos here that you enjoy. Thanks!

Great video! Thanks it has helped me in choosing a laser.

@Geeksmithing

5 жыл бұрын

That's awesome! Glad to hear it!