Great to see local BC company doing such awesome work.

But best adapter kit hands down this thing drivers better than oem. Going from collins night and day difference

Just ordered a kit, super excited.

@FischRacingTech

4 жыл бұрын

Good call More people should be like you If you have any questions about the kit, let me know

@newhirunworn1

4 жыл бұрын

@@FischRacingTech Thank you, looking forward for it to come in!

@barc533

3 жыл бұрын

@@newhirunworn1 how was it?

@newhirunworn1

3 жыл бұрын

@@barc533 Solid, no issues at all.

I Definitely put in the input shaft seal backwards like an idiot lol now I git a leak have to take it down again

Great kit just sucks its missing either a driveshaft or clutch system. $2900 for the kit and shirt throw without a driveshaft and clutch is a little steep.

@FischRacingTech

4 жыл бұрын

Yes, this is the difference between a full conversion bellhousing, and an adaptor plate.

good parts 😊

My guy spinning the input shaft with no gloves.... tough :)

What is the weight of the single mass flywheel? Also I've heard that there will be increased gear chatter without the dual mass flywheel that comes with the vq/cd009 engine combination, do you have any intention of offering this for jz engine owners? My IS300 is such a smooth street car and I'd hate to increase the NVH with this transmission when ar5/w5x combinations don't seem to have this issue. Thanks!

@FischMoto

Жыл бұрын

14lb. Sorry, we currently don't offer a dual mass flywheel. However, we have several hundreds of kits out there with no complaints about this. The CD009 in general is a noisier transmission compared to other transmissions.

the suspensful music hahhhaa whats the soundtrack so ican use it for my pre workout... on a side note if one of those bearing spacers fit does that mean you have the weaker cd009 transmission? also no blue loctite for the flywheel bolts?

@FischRacingTech

2 жыл бұрын

Flywheel bolts installed per arp's specs. The smaller bearings do mean a slightly weaker input, but the main thing you want to look for is triple synchros. If you have proper input shaft alignment (the biggest problem with adaptor plate kits) then that wont be the weak point on your trans, regardless of size.

@pourtierbeatz7804

2 жыл бұрын

@@FischRacingTech none of the bearing spacers fit on mine so ima take that as having the stronger geared one

Fantastic looking item, I’m in the process of piecing everything for my IS with 1j swap. I have a cd009 already that I’m thinking of using, but I have concerns with the stock diff as most people claim the gearing is too short for highway use (daily driving). Is this something you guys have addressed or have any input on what would be best for a solution? Also what makes this different then serialnine kit?

@FischRacingTech

4 жыл бұрын

This is true. The 350z has a 3.5 where Toyota's are typically 3.7 or higher. From our research online, driftmotion has 8" gear sets for as low as 3.58:1 to rebuild your rear end with (all the way up to 5.29) They would be an excellent shop to talk to regarding rear end ratios and matching a cd009's driveshaft rpm

@RollinShot

4 жыл бұрын

@@FischRacingTech thank you, ill look into it.

You need to make a video with the double clutch set up,clutch options and shifter options

@FischRacingTech

4 жыл бұрын

At this time we don't offer any of those items, but will gladly look into specific options, if there is one you would like to use.

@supradrift681

4 жыл бұрын

@@FischRacingTechcan you design flywheel for a Tilton 7.25 clutch ?

@FischRacingTech

4 жыл бұрын

@@supradrift681 that is the clutch that our multi disc flywheel is designed for

Just bought mine :) What type and size sockets will we need for install? I noticed that the ARP bolts are different to anything that I have.

@FischRacingTech

4 жыл бұрын

The arp bolts use 1/2" 12 point sockets. The bellhousing bolts are typical metric allen drive. The bottom 4 are one size smaller than the top ones.

@FischRacingTech

4 жыл бұрын

If you have any more questions I get them faster on Instagram or email, but will gladly reply here as soon as I see them.

Anyone know the size of the bolts that mate the bellhousing to the the engine?

@ChrisT-hp2zi

4 ай бұрын

@FischRacingTech

MAZWORX HAS IT FOR LESS

@FischRacingTech

4 жыл бұрын

Mazworx has their own version which is more basic. Yes it is cheaper, as one should expect from a part rather than a full kit.

The fisch adapter housing is different from the Collins adapter... which is the better way to go?

@BenPetersMedia

2 жыл бұрын

In my opinion the Fisch adapter is better because adapter plates usually have alignment issues which the Fisch Bellhousing doesn't have.

I'll be ordering a kit for my IS300 soon. I was wondering what Driveshaft and Transmission mount will i be using?

@FischRacingTech

4 жыл бұрын

A custom driveshaft will be required, either by modifying your stock one or having a full one piece made.

@FischRacingTech

4 жыл бұрын

The kit comes with a transmission isolator mount. Serialnine offers a trans mount that works with our kits transmission position. Aside from that you can make one from steel

Maybe do a K24 cd009 kit. What mount did u guys use?

@FischRacingTech

2 жыл бұрын

We are doing a k24 next. What do you mean mount kit?

@ammoking6099

2 жыл бұрын

@@FischRacingTech sign me Up for one lol. transmission mount.

@FischRacingTech

2 жыл бұрын

For the jz-cd into an is300, we make a transmission mount. We actually have a few trans mount options on our website!

whats ETA on new orders to Florida? I know the pandemic might have slowed down production.

@FischRacingTech

4 жыл бұрын

We have everything for the kits in stock, so those still go out within 1-2 days of being ordered. USPS estimated delivery times are still in the 3-7 day range So if it goes through customs smoothly, you should have it in under 2 weeks.

With serialnine bellhousing pretty much the same are the flywheel bolts customized as well?

@FischRacingTech

Жыл бұрын

Yes. Flywheel bolts are customized. These Bellhousings have been made by us since day one. They get re-branded for S9 re-sale.

@itsreallytheo

Жыл бұрын

@@FischRacingTech can I get the bellhousing and order the flywheel separately too?

@FischRacingTech

Жыл бұрын

@@itsreallytheo Please contact us via email (info@fischracingtech.com)

Geezus. Ill just snag a getrag for those prices.

@FischRacingTech

3 жыл бұрын

You would be paying more money for a worse feeling, hard to find, used trans, than you would be into a 0km 1000hp capable setup

Hi What clutch can I use with this setup ? CD009 or special made clutch ? Thank you

@FischRacingTech

4 жыл бұрын

It is designed to use the standard 350z clutch

Does it matter if you were to use a manual out of a 370z, they seem to have some electronics for throttle matching... I take it the gearbox would just run fine as a normal manual?????

@FischRacingTech

2 жыл бұрын

yes. It should run like a normal manual.

@danthomas86

2 жыл бұрын

@@FischRacingTech And there's no rattle with your product... I've heard stories of rattling with these swaps... Be it from another well known company

@FischRacingTech

2 жыл бұрын

@@danthomas86 We don't know about rattle with our kits.

What is the recommended driveshaft setup for this upgrade?

@FischRacingTech

4 жыл бұрын

Hi. We have always ordered new 350z slip yokes then taken our oem shaft to a local driveshaft shop to have them shortened the appropriate amount. Because our kit is shorter than the typical auto bell/adaptor plate, I am not sure of an OTS solution for a driveshaft.

What starter is needed for the jz cd009 bellhousing?

@FischRacingTech

2 жыл бұрын

Any jz starter will work.

This adapter works on a jk41 transmission from Nissan?

@FischMoto

Жыл бұрын

yes

in the end the length the gear stalk position of the cd009 will be similar to r154 or it will be pushed more rearward?

@FischMoto

3 жыл бұрын

It will be quite similar. The CD999 was developed by Serialnine to work in Lexus/Toyota chassis, without having to cut the trans tunnel. They have altezzas, crowns, jzx, and aristos as their shop cars, so being similar to R154 was definitely something they had in mind when designing the shifter.

@AcheLone

3 жыл бұрын

@@FischMoto thank you for the insight..

Wait isn’t this a rebranded Serial Nine cd pro or who made this first?

@FischRacingTech

2 жыл бұрын

These Bellhousings have been made by us since day one. They get re-branded for S9 re-sale.

@nicheniche

2 жыл бұрын

Good to know, thanks for getting back to me

Do you make a kit for a 1uzfe to Cd009? Does the shifter need and modifications for the swaps?

@FischRacingTech

3 жыл бұрын

Hey Ty, Our UZ test car is currently getting wired up, and should be on the road soon. Once we have tested it to confirm fitment we will be launching the UZ bellhousings. In theory that will happen before Black Friday, so quite soon

@FischRacingTech

3 жыл бұрын

As for the shifter, we currently offer the Serialnine CD999 which works well with the CD in most chassis. What car were you looking at putting it in?

@tycharles241

3 жыл бұрын

I’m planning on putting it in a 2009 BMW 335i.

@FischRacingTech

3 жыл бұрын

@@tycharles241 gotcha. Idk what cd location is like with e9X chassis. Might be a test fit then order shifter type situation

that adapter is for brz / frs / gt86 ? ,and could you send him the link to buy that adapter for brz / frs / gt86? Thank you

@FischRacingTech

2 жыл бұрын

Sorry, not available for this car/engine.

@arcangeldelagurda

2 жыл бұрын

@@FischRacingTech ok Thank you

Do you do any kits for a JZS147 Aristo (GS300)? I want the shifter to be somewhere near the stock position.

@FischRacingTech

4 жыл бұрын

At this time we do not offer our own shifter. We have some serialnine cd999 shifters on hand that make the position nearly stock, on most Toyota sedans.

@tawidave7092

4 жыл бұрын

@@FischRacingTech Have purchased this Kit. On its way. Just wanna check, can I us a twin plate clutch if it was designed to replace OEM 350z?

are you doing a sr20 to cd009 swap kit?

@FischRacingTech

3 жыл бұрын

We haven't started one yet but I think is the most requested option. Maybe next year?

@mitchellviney2089

3 жыл бұрын

@@FischRacingTech will this come for both rhd and lhd?

Will this kit fit an SC300???

@FischRacingTech

2 жыл бұрын

Yes. It works with a 2JZ.

Do you make it for a ls1 conversion cdoo9

@FischRacingTech

4 жыл бұрын

Hey Peter. We do, it will be available to the public soon. Currently we have one LS unit being tested in our shop g35 and it has had 0 issues. Follow us on IG or FBfor updates about its release

@PeterHatch-mx7zc

4 жыл бұрын

@@FischRacingTech thank you for your reply im in for one thks

@PeterHatch-mx7zc

4 жыл бұрын

May I ask ?? What will be the clutch and fly wheel to use with the ls1

@FischRacingTech

4 жыл бұрын

@@PeterHatch-mx7zc for single discs you can use any 350z clutch. Multi disc is a little more complicated but the kit is designed around the Tilton OT-II twin and triple disc 7.25"

You need to do a start up so people can hear the rattles. 🤣

@FischRacingTech

3 жыл бұрын

Whats your ig so i can send you a video. Not sure if its your clutch or the collins kit, but there are no rattles in any of our test cars.

@PeaceSTAR253

3 жыл бұрын

@@FischRacingTech pearce_the_hood_hippie I have the Collins kit on mine.

@PeaceSTAR253

3 жыл бұрын

From my understanding it's the flywheel being to light to absorb the vibrations from the motor then transfered into the input shaft.

@FischRacingTech

3 жыл бұрын

@@PeaceSTAR253 how much does it weigh

@PeaceSTAR253

3 жыл бұрын

@@FischRacingTech I'm not 100% sure because I bought the car swapped already but I think collins uses the fidanza flywheel that's 13.5 pounds.

hello sir?

@FischRacingTech

3 жыл бұрын

Yes, hello?

@geloebreo6611

3 жыл бұрын

thank you sir for your response i wanna ask something sir if u want to hire a mechanic sir i am from the philippines i was working before in saudi arabia sir southcoast tuning sir.. thank you sir

a kit for the rich. meanwhile domestic muscle cars have aftermarket bellhousings for $300 :/

@FischRacingTech

3 жыл бұрын

Will terrible alignment issues. There are cheap kits out there for jz - xx transmissions as well. Unlike those kits we havent had a single customer break an input shaft at any power level (yet) A JZ swap making enough power to require a non toyota trans is not a cheap junkyard build