Can’t believe the complaints about the movement. Be glad for what this is: something free that helps you save hundreds in repair costs. It sure did for me!

@coffeetricksandtips1018

7 ай бұрын

Sweet! Nice to help You. 🥰

where/when did u fix grinder??

Thanks for this video. I had the water level warning despite the tak was full. I bought my ENA4 at a Cash Converter Store and they did not have the cardboard packaging. I think that the Jura was shocked in my trunk. After opening the covers I saw a small PCB board moving freely... That was the sensor which operates through the plastic cover. Once fixing it with a tape, everything works, no more error message.

Words needed 0%. Information content 100%. Nice!

Very helpful, thank you. May I make a suggestion? You might want to consider getting a stationary camera. All the movement makes this hard to watch.

Hello and thank you for this very instructive video. Could you please detail the tool you are using at 01:13 to get the 4 screws out. ++

this is a good vid for disassembly and reassembly but fails to offer assistance on cleaning/fixing problems with the grinder as mentioned in the title

Thanks for the videos you make 👍 Easy to understand! As I don't have this machine, would I be correct to assume that disassembling the side panel like in the video, I can get a better reach of old, build-up of ground coffee and potential mold, and making it easy to maintain longterm?

thank you !!

Just felt the need to add a note as it isn't too clear in the video. The two black covering strips that are removed at the rear of the machine do not pop off outwards. They should be slid up then out.

@Pobee

6 ай бұрын

Yeah, I had to watch the video a few times. Plastic is easy to break!

Am I missing something here? Didn't see you do anything with the grinder?

Did you ever tried to remove the front panel where are the 3 screws located ? Under the Ena sign? Is it doable I mean can we go and clean there or it is all attach and can’t get access?

Thanks for the vid!! I'm stuck with getting off the left side panel, feels like it will crack, you did it so smoothly, whats the trick? Also, to get out the circle screws without jura tool, just tighten the chuck of a drill and it comes right out

@BrianReese

2 ай бұрын

Hopefully you figured this out already, but it slides back slightly towards the rear of the machine, then comes right off. I was also stuck here for a moment, maybe this helps someone else 😅

Thanks!

On back of ours the covers are held with some sort of rivets/ pins not screws?

@flaviomuratore

Жыл бұрын

Same here. Did you figure out how to ooen?

@tomp.8129

Жыл бұрын

@@flaviomuratore Yes, Jura do special key for these you can buy with service kits but I just used long nose pliers to remove them and replaced with normal Philips screws as you would be needing to clean the brewing group probably twice a year or so.

@flaviomuratore

Жыл бұрын

@@tomp.8129 thank you very much.Apologies for bothering again but I am not used to these tasks. You just straight up pull the rivet out of there by using sheer strength?

@tomp.8129

Жыл бұрын

@@flaviomuratore They are screws, just oval shaped heads - grip tight and unscrew.

@flaviomuratore

Жыл бұрын

@@tomp.8129 so glad I asked! Thank you very much Tom!

Just before you replace the covers, you appear to be pressing 2 buttons. Am I correct and are they resets for the grinder motor?

Can you buy new grinders and from where please?

How to fix the monitor? Mine is just White light

Which one is more profesional i mean inside, jura ena8 or jura e8?

@coffeetricksandtips1018

Жыл бұрын

Hi! More professional ir E8! New’er model :)

@belakulcsar

Жыл бұрын

@@coffeetricksandtips1018 betwen older model e8 and ena8 which one to chose? I found them used and this whay i ask, which one to buy? From what i have understand, the jura use electronic presure not mecanic. I oscilate betwen jura ena 8 or e8 , miele 5500, gaggia academica , siemens eq9 s700 , all 4 i have found them used near 400e. Is jura a bether option from all 3?

which tools are u using; specifically at minute 1:19

@coffeetricksandtips1018

Жыл бұрын

It’s a special Jura tool! Like a litle oval..

@valentijnbruggeman936

Жыл бұрын

@@coffeetricksandtips1018 thx, i have a jura ena 8 so the tool should fit!

@johnsilva3422

Жыл бұрын

@@coffeetricksandtips1018 where can I get one of these tools?

@richoldridge5388

Жыл бұрын

@@johnsilva3422 Amazon Service Repair Tool Key For Jura Capresso Open Security Oval Head Screws

@flowpointFR

Жыл бұрын

Or a nice pair of letherman.

Wow! No wonder they charge so much for a service! Mine doesn't go six months without breaking, and that's with only one coffee drinker in the house. Better to buy a Breville or any other brand!

@coffeetricksandtips1018

Жыл бұрын

Jura not bad! Actually i like Saeco and Delonghi :)

@r.f.5858

Жыл бұрын

totally true, here 2 drinkers and after not even 1 year, it was leaking water and coffee mold.. saeco we had 3 years before there was anything wrong with it, less expensive also. both cleaned frequently enough.

@SeaOfMadness

Жыл бұрын

Had mine for over 2 years - Around 8-10 coffees a day every day, maintain it relatively well and never had any issues.

@xStaman

Жыл бұрын

@@coffeetricksandtips1018 Where exactly in the video did you fix anything? You loosened the three screws around the bean holder assembly and thats ALL you did. Total waste of time

Thx y

@coffeetricksandtips1018

2 жыл бұрын

Welcome 😉

A stable camera and some narration would have been very helpful but otherwise good video

@coffeetricksandtips1018

Жыл бұрын

Yes i agree about camera and etc… But this chanel and all videos not my main business. It’s Just for Help other people ;)

My question also.

If you can't speak might be a good idea to hire a narrator. Only thing I got from this was how to disassemble the unit and there are some tools (unknown type) that allow you to do it.

I get seasick with this video...the movements of your head.

@coffeetricksandtips1018

Жыл бұрын

OK :)

@danmusicman2010

Жыл бұрын

​@@coffeetricksandtips1018approx how much to fix a jura ENA8, comes up fill beans when there full, must be a grinder issue.. Thanks