Awesome 👍. I saw on Craigslist a rear PTO kit for my 1974 John Deere 110 but it was $700. Which I think is crazy for that price because I can buy a 540 PTO kit for my John Deere X575 for only $200 more.

@mmrbeef

4 жыл бұрын

Wow, that is pretty high for a PTO kit for a SF. Normally those run in the $150-200 range for the 540 PTO.

@jmgredgreen4x428

4 жыл бұрын

@@mmrbeef Yes it is. Where did you get that red quick hitch that you installed on your John Deere 455?

Did they make a 540 gearbox for the 318?

@mmrbeef

11 күн бұрын

A direct drop in 540 gear box, no they did not. However, Peerless did make a 540 rpm gear box for a utility vehicle. If I’m thinking right AM134155 is the part number. They do come up for sale from time to time but they are expensive! If you fine a NOS one you have to shorten the output shaft. There are several threads on WFMachines.com and other forums with pictures etc. I had a couple and sold them over the last couple years.

Where is a good place to find the parts to put a rear pto on a 420? We dont see a lot of these tractors down here in the south so something like this is really not seen much at all but I need a pto to run a tiller.

Cool video! Do you know we’re I can buy those front tires? Thanks

Where did you get the PTO from and what starts and shuts it off?

Is it the same parts on a 420?

Are you on Facebook?

My 318 has lost forward and reverse gears after I bumped a stump with the deck. Have you ever heard of this

@mmrbeef

3 жыл бұрын

Is there still hydraulic power to the lift functions and steering? If there is no hydraulic power at all, the pin on the shaft that holds the pump gear in place has most likely sheared. If there is still hydraulic function the issue is probably I. The hydrostatic linkage or the differential.

@stevebillow395

3 жыл бұрын

@@mmrbeef all I have is a motor that runs. No movement of anything

@rgoldsmith6560

3 жыл бұрын

Did the release lever get bumped? It's under the right fender well pull it out and twist to release hydraulics to tow, the valves often will stick in released position, they take some delicate probing to get free. Hope that's all it is.

@stevebillow395

3 жыл бұрын

@@rgoldsmith6560 no the hydraulic pump was trashed

Avid watcher. It would be nice if you recorded start to finish the projects. I want to install a PTO on my 88 JD 318 . You did the same thing on the 1100 generator and so on.. I for one would like to go on the journey with you. Think about it. You are giving us how to videos and you have a eBay store. Its benefiting you to give us limited edited videos.. Your already doing the work...don't stop the camera

@mmrbeef

4 жыл бұрын

Thanks for the feedback, I will certainly keep that in mind. In the past when I have done longer videos the views and the length of view times goes down substantially. I have a couple 30+ minute videos and the average view time is less than 3 minutes. Meanwhile if I work hard and keep them short the average view time can be 6-7 minutes. I will see what I can do moving forward, just never seemed like my viewers wanted the 30-50 minute videos some of the other channels make. Thanks again for the feedback. I don't know unless someone says something.

@billyhanna2688

2 жыл бұрын

@@mmrbeef just found you on KZread. I got a jd332 that ive just barn found and will need your help. Is there anywhere else you post? Website facebook etc.etc