I just did my cap and rotor with new wires, also put in a new fuel filter on my 1991 YJ. Finally got it running after 11 years of sitting. I will now be doing the senors for sure. Thank you👊🏻

Extremely helpful video. This is the main reason I want a YJ. Extremely easy to wrench on and mod.

I have to thank you big time! Am no mechanic by any means, but this has been the best explained /detailed video on how to I’ve come across. Followed instructions to the T! Thanks!

Thank you so much for this video. My jeep was running so rich these sensors fixed it. Your video was very indepth.

I changed all the sensors in my jeep today . It purrs like a cat to . Check engine light when off . It doesn't idle high and low no more . It runs so much better . Thanks for the vid

This video is soooooo AWESOME! Very well done, to the point & watchable! Must know stuff for YJ clan...

Great video man, THANK YOU! I have a YJ 87, it is missing a lot of staff, previous owner did not care. I'm trying to bring it back to life, this video will help.

This is perfect! Just picked up a 95 YJ and will be doing this soon.

Thanks for taking the time to make this video! A lot of help for me. 👌

I have a '95 YJ. Had been having issues with intermittent high idle depending on ambient temperature outside. Would start in the mid 80's at about 1100-1200 RPM, up to 1800 RPM once it hit the mid 90's and up. Another mechanic finally figured out that the computer wasn't relearning the IAC Valve after it was replaced (it was bad). He had to use a computer to take control of the IAC and adjust it correctly because the computer wouldn't. Had the problem for 10 years. SO happy it's fixed- FINALLY!

Absolutely top notch, valuable video. 94 yj 4 inch lift.

Dude - THANK YOU, for this video, this is a HUGE help to us newbies, great shots of the parts and names and excellent views of the install, thanks again brother....

Dude God has blessed me with you're video. Thank you Sir. My jeep has they absolutely worst surging idol and when I put my clutch in she dies out and is very very dangerous. Tomorrow morning I'm defiantly I'm cleaning my IAC and my Butterfly. Thank you so damn much.

great vid, that will help me a lot in my YJ maintenance

GREAT video, thanks! I'm about to get a 93 YJ, first thing I'm doing is new rotor, cap, plugs, wires and sensors

Changing sensors after a period of time is wise-preventative maitenance. I had a vehicle with 150k, changed each sensor as cash allowed and most of them made subtle differences in engine operation. Taken together it makes a nice improvement. I pulled apart my TPS (the original) and the wires inside had a lot of white corrosion on them. Given that its job is to send a signal back to the computer to manage overall operation its important to have a clean signal. Corrosion will affect resistance and in turn send a weaker signal back to the computer. Changing the TPS made the single largest sensor improvement as far as "seat of the pants" go.

The editing for this video 👌

Thank you so much! Great video and super helpful!

Thanks for posting this sensor vid. I have 1997 Jeep XJ Sport that has been having some issues even after having the engine rebuilt. I'm going to replace the sensors, plugs, cap & rotor and I hope that will make a 100% improvement. The 4.0 I-6 is the workhorse of Jeep's and I know I can improve its performance with simple maintenance. Thanks!

@keytaylor2103

6 жыл бұрын

Mark did changing the sensors help

Great upload!

good advice. Dont forget crank sensor, classic point of failure.

I had to look up the song at the end. That's a great vibe

@gabeburnett6980

3 жыл бұрын

what was it?

Great video! Very informative and thorough. 👍

@Archifx

7 жыл бұрын

+Matt thanks!

Video helped me out a lot thanks

Nicely done!

I love it that you’ve got the e-break light tripped as well! Haha same here bro. Bungie cord will help pull the e-break up and not keep it depressed to trip the light. It’s on my fix list too. >.

Outstanding video! I just bought a 1992 YJ and I really needed this. I'll be doing all these sensors right away.

Immensely helpful. Thank you.

Very informative. Thank you.

Thanks for your time. Thanks for sharing. 94' rebuild

Thanks great video!!! helps alot!

Love the video great tips thanks

Outstanding info, very well presented, extremely useful. Thank you

@Archifx

Жыл бұрын

Glad you enjoyed it!

Thank you for this video, my 95 2.5 L loves it too.

@MyShayShow

5 жыл бұрын

I have a 95 YJ 2.5. I need to do this!!

@Archifx

5 жыл бұрын

Do it!!! You’ll love it. It only takes time, money and passion ;)

Very nice video good job

Great vid! Thanks for sharing - One thing I'd add is for long-distance Jeepers 87-95 w/EFI 4.0's - Keep a spare CPS (Crank Position Sensor) in your gear bag. Either that or keep some de-greaser on hand and keep it clean. The magnet gets gunked up and dirty, throwing the timing way out and you may not be able to fire it up - It happened to me. Happy Jeeping!

@dereklund3157

4 жыл бұрын

yep happened to me out in J tree

Great video. Looks like you live in beautiful Florida.

I live in the U.K. and i have a yj 2.5 , have owned this motor for about 4 years and i absolutely love the old bird , dont see many YJs over here and in summer it is the most fun car on the road with the roof off and doors off she turns heads where ever she goes, i believe that every one should own a YJ at least once in their lives , she is 24 yrs old and when cleaned up she looks as good as when new ,bright red and loads of chrome, thanks for reading and hope i didnt bore you .

@MrBarboza92

7 жыл бұрын

ray spencer ✌✌👌👌👌🍻

@csn6234

6 жыл бұрын

Here in the States, real Jeep owners eschew chrome.

@Archifx

6 жыл бұрын

+Chris Nelson I don't get it? It's a real jeep

@csn6234

6 жыл бұрын

archifxllc I'm not saying his Jeep isn't real. I am saying Jeepers -- the ones who take their rigs to Moab, who are in clubs, who are all about the Jeep life -- don't like chrome. Shiny chrome belongs on pavement queens.

@Archifx

6 жыл бұрын

+Chris Nelson why?

Also let me just say fantastic production, shots and graphics. Are you a designer by trade. It really doesnt get any better in the diy realm than this

@Archifx

5 жыл бұрын

Thanks man

Thank for sharing!

Very Cool Video!!!... Thanks!!

GM part label on MAP because a lot of engines were used in multiple vehicles, eg my YJ motor also in some chevy cars

great information....thanks

my next paycheck project

thanks for the video man! im going to do this to my 2.5l. question though. what steering wheel adapter are you using and what steering wheel? i love the look of it.

Idled the same as it did when you started it as to when you finished it hahaha sweet

@Archifx

5 жыл бұрын

Lol. That was for effect hahaha. Started the video with the finished result. Video is how I got there. Smh

HUGE crack on that header pipe!

Excellent, thank you. I see the header collector has a crack, so typical of the 4.0 !

Don't forget the oil pressure sensor. Changed mine and stopped a bad oil leak

Thanks for the vid! Is this for the most part the same for the 2.5 engine?

one thing about the Idle Air Control valve...when you remove it, there is an O-ring that you want to make sure you don't damage when re-installing.

@sergioherrera3029

3 жыл бұрын

Put silicone .

@revolutionday1

2 жыл бұрын

@@sergioherrera3029 Uhhhh no.

@sergioherrera3029

2 жыл бұрын

@@revolutionday1 I'll get the ring 😂

Any issues with the parts provided in the links? Some of the amazon reviews say they don't last or start to bug out compared to buying from a parts store

I intend to change myself the catalityc conversor but my doubt is if the 1995 model has or not a sensor plug mounted on te conversor? Thank you for your help!

When I first got my 95 yj I changed everything but the map mine has always has a lagging on take off umm looks like I’m doing a map sensor thanks

90 yj wrangler sounds good

You are a brave man putting all that import autozone advance junk on at once. I have had 20s or more of parts be bad right out of the box. Not to mention say in the case of the o2, the 4.0 likes a certain factory brand and doesnt play well with others such as Bosch

@Archifx

5 жыл бұрын

Still running well today. No issues with these parts installed in the video.

@SeriouslyAwesome

5 жыл бұрын

He did use NTK O2 sensors, which are OEM. But yeah, I personally wouldn't do them all at the same time in case I needed to troubleshoot a problematic one

ive got the amc 2.5 liter engine,my MAF sensor and the Manifold temp(hot) water, both inputs are 2.34 volts and they both got back to ONE WIRE?, Ive got the renix computer and I thinks its shot, all sensors have input,voltage and send out signals but no computer response

Thank you so much for sharing your video. I have a YJ 93 do you know anywhere I can buy parts online like leaf springs all the bushings for the front suspension Etc online I live in Northern California please advise thank you so much Joe Dirt NorCal

Great video, but I purchased the IAT from your link and it's not the same one. Only has one connection inside instead of two

nice

Another good sensor to maintain or watch is the crank/cam shaft position sensor, there are about 3-4 different sensor types depending on the year of the yj. If it dies or stop working, the jeep will not turn on. Trust me it happened to me lol

I have a 1992 2.5 litre and want to replace all the sensors. Where do I get the list of them and get the best price? Also is there a video on how to replace them on the 2.5?

what year is your jeep and what is your operational running temperature?

Anybody know what parts become compatible, if for example I have a 91 YJ but a 97 2.5 (TJ). Say for instance a starter. Am I okay getting a tj starter for a tj engine? Stuff like that. Is there a point where it may not matter. It could be compatible with a yj? This jeep seems to be TJ in its engine, transmission, and transfer case. Or changing out the heater core. Can that be a YJ heater core instead of aTJ heater core? I'm guessing sensors all around and muffler sensor better be TJ related? It makes it so much fun asking for parts at the parts store.

Is there a list of all the parts?

My 1992 Jeep Wrangler hesitates a bit to turn on. It takes about 2-3 cranks to get it started. Idles okay. Would this help ?

I got a 94 yj that's running very rich. do you notice a little better gas mileage?

looks like you need to fix that windshield wiper next.

Hey thanks for this video! I ordered all of these (which btw make sure you do some shopping around before you go to one store and just buy them all you can easily shave $50 bucks off the price that way). Anyways, I'm having sputtering, surging, terrible gas smell, code 52, and around 3k rpm the jeep starts to lug out as if you have a limiter or are pumping the gas petal up and down. Hopefully these will help it out and make it run good again. I'll let you know!

@Archifx

7 жыл бұрын

Skippy A these parts should help you. Sounds like the ecm is trying to over compensate by adding loads of fuel for the miscalculation of air / spark / timing. All of these things are what the above mentioned sensors are trying to achieve. These sensors are trying to create a harmony with the engine. The gas smell is obviously the engine running rich and the sensors are what tell the ecm to make the engine run rich. Clean your throttle body real good when you replace your sensors and make sure to come back and let us know if it helped.

@noble2kat142

7 жыл бұрын

Alright well here's my follow up. Overall, the Jeep is running better. At stop lights the engine would want to stall when picking back up in first gear and that made for some pretty embarrassing moments haha. So the surging has been taken care of and it warms up from cold a lot better now without sputtering and such. However, I've run a good gas tank through it and code 52, gas smell and the odd issue of not wanting to go past 3k rpm persist. I'm at my wits end with this issue. I'm suspecting that the Catalytic converter might be clogged and therefore causing build up in the down pipe where the O2 sensor is and that is making the Jeep read rich. Does that make sense?

@noble2kat142

7 жыл бұрын

I've also done some modifications to the Jeep that could also be a cause of the issue. I have a 2.5L 4cy and in order to give it a bit more "Umph" I swapped out the 2.5L throttle body for a 4.0L throttle body and added 19lbs injectors to it. My friend did the same mod with no ill effects though so i'm skeptical.

@mariordz76

6 жыл бұрын

Thanks for the video/comments I do have all those fails and terrible gas smells. I will replace all of them

Now it's time for Dana 60's and forties.

my yj starts up with a low idle below 1000 and stays below kind of rough abit. ideas? 2.5l

i'm building a jurassic park jeep this spring! i got a 1993 jeep yj sahara edition!

@MrBarboza92

7 жыл бұрын

Colton Taylor im trying to do the same with a 95 i just got 👌✌

@redsnowdue

7 жыл бұрын

I have a 93 too brother. Fixing it up for high school

@Archifx

7 жыл бұрын

+Rylee Ellingson nice!!! Good luck with it

@FPSNovaS

6 жыл бұрын

Colton Taylor I'm currently fixing up a 95 rio grande with a 89 4.2 and 3.5" over all of lift and it's almost complete

@jcwoodman5285

5 жыл бұрын

I've got the 92 Sahara...

Great video. But, replaced the IAC and now it idles at 3k. Can't get the TPS out due to stripped bolts. O2 has possibly never been changed because it isn't moving if my life depended on it and I don't want to replace the entire pipe. Old cars man.

Great video! I am new at all this (just bought my first 92 YJ) so it was very helpful. Quick question though: after I changed the MAP sensor, I started the rig, the check engine light came on, the start was difficult, and the Jeep idled weird (high). Any thoughts?

@Archifx

3 жыл бұрын

Disconnect battery for 1 minute, reconnect. Let it run for a few minutes. Let the codes all establish new baselines. Should straighten out. If not, check the new engine code to see what other failures you have.

@frederichairson5822

3 жыл бұрын

@@Archifx Awesome! Will try that! Thanks!

this works on the first gen 1989 yj jeep 4.2

Is the IAT the same as the Air Charge Sensor? 😬 😔

Great video but the music is annoying/distracting at times and makes it hard to understand what you're saying.

@erickortega754

Жыл бұрын

Music is good I like positive music

@carinnedavis5531

7 ай бұрын

I think u are being negative the music is fine and he speaks very clearly and just fine! I can hear him perfect!!

I have a 1991 Jeep Wrangler YJ, 4.0, 5 spd., Is there any reason NOT to use Auto Zone or O’Relly parts, for this job? I’ve heard roomers they have subpar parts for Jeeps? Who do you recommend for all high quality Jeep replacement parts? I have had fit problems with my motor mounts & VSS: Vehicle Speed Sensor, wrong threads on both and was told my new rear drive shaft U joints were subpar. And what about the Crank position sensor, when should you replace that sensor? Thanks for a great video, keep up the great work.

@galehess6676

6 жыл бұрын

just depends on the year in which you bought or are buying and which parts, their quality can vary, as can any company's, due to moving manufacturing to/or back from china, specs changing, getting a bad reputation and trying to rebuild it..... a lot of info on who's parts are bad is old and they are now good again, or vice-versa for example, do (2017) get an odyssey battery, but don't get the others that used to be good

Changed all sensors, the computer caps; still rough idle (high/low uncontrolled) for 2-3 min after starting….

I have a Jeep Wrangler YJ 1994 with 124k miles

How is life with a YJ?

you aren't kidding about driving someone crazy, our 99 jeep cherokee sport 2 door had a CPS go bad and it would crank over all day but never fire up. one $40 sensor later she purs like a kitten

@jcwoodman5285

5 жыл бұрын

What's the cps?

Good vid. That header is cracked.

@upliftmofopartyplan1156

5 жыл бұрын

15:37 in the typical location adjacent to the weld

Very helpful! Thank you. Purring like a kitten. Question: The O2 sensor is frozen and can't remove it. Thoughts on getting it out?

@TT-dd2tv

3 жыл бұрын

Mine too. Apparently the rust fused right into the pipe and I would have to replace the exhaust pipe.

@Archifx

3 жыл бұрын

Don’t remove it then... drill a new hole and add an O2 bung

@Archifx

3 жыл бұрын

Get something like this. Add a new one www.holley.com/products/exhaust/builder_components/exhaust_components/parts/71014302-RHKR

@TT-dd2tv

3 жыл бұрын

@@Archifx dammmmnn. Haha No idea they made this. I covered up a hole in the exhaust pipe of a Honda with something similar.

✅

I got an issue with my 94 yj that has been bothering me for a while.after driving for like 30 minutes or more,when i stop and try to restart the jeep,it cranks but will not start.so i have to wait for some hours then it will start like magic😄😄..i appreciate your thoughts on this.thanks!

@Archifx

3 жыл бұрын

EGR valve. Pull your codes

Might be a stupid question: Is this Jeep fuel injected? I have a 90 and it has a carburetor with a round filter up top.

@williamalexander6688

7 жыл бұрын

Adrian Angulo that jeep looks fuel injected they didn't start doing fuel injection on the six cylinder until 93 or 94 when they came out with the 4.0 before then it was the 4.2 carbureted

Haha 18:31 “I replaced the cap and rotor off camera.... If you don’t know how to do that, get the f*#k out”. 👏

Before watching the video I went ahead and replaced the IAC and TPS. The RPM when it is now idling at 1000, is that still too high? Or do you think I should replace the other 3 parts as well? I also cleaned the throttle body flap really good, it was reallllly bad before.

@Archifx

7 жыл бұрын

+Mikeyy too high. Should be somewhere round 500-700 rpm. Replace all and do the plugs and wires.

@MikeyyAlan

7 жыл бұрын

I mean if I can't get to it right away would that be an issue? If I has to wait about a week or two? Very light driving btw. I don't think so but just thought I'd ask.

@MikeyyAlan

7 жыл бұрын

plugs and wires were done too***

@galehess6676

6 жыл бұрын

do O2 sensor!!! :) very likely, and rotor plugs wires cant hurt if more than 20k on them

Could you tell me which is better?? BOSCH or NTK parts . I'm putting on a new oxygen censor

@galehess6676

6 жыл бұрын

bosch is what i used, would tend toward bosch being better quality, they are probably more $$

@zjty233

6 жыл бұрын

Giovani22 got for the ntk jeeps run better with that brand, Bosch tends to crap out

@mndzmkl

6 жыл бұрын

I agree with NTK. I've read nothing but good about NTK with Jeep.

great video, but i was wondering how come the parts in the video are car quest parts and the links are to off brand parts...

@Archifx

Жыл бұрын

Was available at the time online.

@yaadies

Жыл бұрын

@@Archifx oh okay, so I'm looking to do a super tune on my 92 YJ and was wondering if I should use the links you gave or the more expensive ones which won't cause any malfunctions or any problems

@yaadies

Жыл бұрын

@@Archifx or are they all the same thing?

@Archifx

Жыл бұрын

Go to Advance auto and get them

I own a 1995 wrangler. The map sensor is a GM. THE ECM COMPUTER is a Chrysler mopar. Jeeps in those years had many parts from different factories. Why? Is the question.

@felixmikkialmosttoasted3911

3 жыл бұрын

As amc owned jeep prior to chrysler , they sourced parts from other automotive manufactures. They then pieced the jeeps together.

Hey does anyone know what song plays at the end of this video

@Archifx

4 жыл бұрын

Hey man. I tried to go back and remember what track it was. I know it’s Andrew Applepie but I need to dig deeper to find the track.

Which IAC manufacturer do y'all recommend for my 95 YJ?

@Archifx

5 жыл бұрын

Not sure of brand but the one I installed in this video is still perfect years later. Just don’t get the cheapest one. Get one that’s recommended by your parts pro at the big box store.

@MyShayShow

5 жыл бұрын

@@Archifx Got myself a new IAC, when to install it today and noticed that the electric connector wires are a bit severed. WTF??!! Any idea where I can purchase a new 95 jeep wrangler 4 Wires Electrical Connector Idle Air Control Valve.

The reason it says GM on the sensor is that older jeeps are notorious for using a bunch of different parts on the vehicle. Alot of GM parts and sensors are used.

@galehess6676

6 жыл бұрын

yes! can get gm sensors for replacements, some from various chevy cars, etc. for the 2.5L jeep

Sometimes used sensors are a good choice, because aftermarkets are such poor quality and don't meet spec, so even a new sensor will make the Jeep run poorly. I had to use a used air-temp sensor.

Hardest part of changing the maps sensor was finding a 7mm wrench

How do all of your gauges work?

@Archifx

5 жыл бұрын

Thankfully they all worked when I got the jeep.

should have just taken out the throttle body. 4 10mm screws. clean idle passages and clean with carb cleaner with sensors out of coarse

How many miles i need to have for this super tune up?

@Archifx

4 жыл бұрын

100k and up