Jeep Wrangler Tj - Axle Tube Sleeves & Other Mods Lj | Xj | Yj
Тәжірибелік нұсқаулар және стиль
The Barns 4wd Axle tube sleeves are designed to add strength to the thin, and bend prone front axle tubes on your Jeep Wrangler or Xj/YJ/MJ/Zj With Dana 30 or 44 front axles. Today two different types of tube sleeves are available press in and weld in. While the press in tube sleeves offer the convenience of not having to weld, they also sacrifice strength. The press in tubes only have one point of contact at the outer end of the axle tube that relies on an interference fit. The Barns 4WD weld in version offers up to 9 points of contact, that when welded become a part of the existing axle tube totaling up to 1/2” wall Thickness. These sleeves are compatible with 35 spline aftermarket axle shafts. We weld in two tube sleeves one short and one long, removal, disassembly and cleaning of your axle is required. I also installed the Barns 4WD Lower control Arms Skids If you are looking for the ultimate in protection for the front lower control arm mount, 3/16 thick in material, Not only will you have protection for your lower control arm suspension joints, this will add much needed reinforcement to you lower control arm mounts that hang low and are very susceptible to being bent or deformed when coming into contact with obstacles on the trail. All of these mods are budget friendly and very affordable for what they do. Check out all the products in the build list and Links below. Thanks for watching. 🍻
Dana 30/44 axle tube sleeves: barnes4wd.com/products/jeep-t...
Dana 30/44 lower control arm skids: barnes4wd.com/products/tj-lj-...
Tools and Links:
OEM balljoint press: amzn.to/3Uy1zq7
OEM Balljoint Master Adapter Set: amzn.to/4aj1vAu
Drill 1/4”: amzn.to/3UOJvtf
7/16” drill and Tap: amzn.to/4bc4oUZ
Drill 1/2”: amzn.to/4duPRW3
Rapid Tap Cutting oil: amzn.to/3UU7NRF
Dewalt Drill and impact set: amzn.to/3QG47Sa
Round files: amzn.to/4bqc4Dr
1/2” impact driver: amzn.to/4ad08mL
1/2” deep socket set: amzn.to/3Uxmr0J
5pc scrub brush set: amzn.to/4a8GbxH
6 piece wire wheel cup brush set: amzn.to/3wzTkBW
Purple Power Degreaser: amzn.to/44Cx8DT
Forney Welding hood: amzn.to/4dqh24e
Forney Welding Gloves: amzn.to/3wpJMcT
Lincoln PPE sleeves: amzn.to/4bar8Vl
Z87 Safety glasses: amzn.to/3QCmNCa
Hobart 190 Welder: www.amazon.com/dp/B005CNOVZU/...
Welding Table: amzn.to/3WBAxkA
3T jackstands: amzn.to/3ynFVgM
Support ATEM OFFROAD here: Atemoffroad.com
The “GlueTreead” kit that replaced my spare tire:
amzn.to/3UhwdoZ
OPENROAD 4WD
10% OFF USE PROMO CODE: ATEM10
OPENROAD4WD Panther 2 13k Winch
Synthetic/ wireless
openroad4wd.com/collections/h...
DISCLAIMER
Due to the factors out of control by ATEM OFFROAD, we cannot guarantee against improper use or unauthorized modifications of this information ATEM OFFROAD assumes no liability or responsibility for property damages or injuries incurred as a result of any information contained in this video. Use this information at your own risk . ATEM OFFROAD recommends safe practices when working on vehicles and or with tools seen in this video, any injury damage or loss that may result from improper use of these tools equipment or from the information contained in this video
Is the sole responsibility of the user and not ATEM OFFROAD. Be Safe
This video and description contains affiliate links which means if you click on one of these product links, I’ll receive a small commission. Thank you
Пікірлер: 28
Looking good and should be good and strong. I need to run axle sleeves in my 30 and have the Artek track bar mount welded in . Looking forward to your next video , take care .
@ATEMOFFROAD
Ай бұрын
Absolutely I have no doubt this will be stronger, wasn’t sure if Artek has the sleeves but I did see that they have some strong brackets and trusses. Thanks for watching 🍻
Good job man! I like that brush extension, that was a heads up move😎👍
@ATEMOFFROAD
Ай бұрын
Thank you 🙏 I appreciate it 🍻
awesome vid
@ATEMOFFROAD
Ай бұрын
Thank you 🙏
Nice job!
@ATEMOFFROAD
Ай бұрын
Thank you 🙏
Nice work!
@ATEMOFFROAD
Ай бұрын
Thank you 🙏
Damn bro, you got skills!!
@ATEMOFFROAD
Ай бұрын
Thanks bro, we need to hit the trail when I’m done here, 🤝 ✅ 🍻
@theangrycamper
Ай бұрын
@@ATEMOFFROAD lets do it!! Sourgrass, what do you think?
@ATEMOFFROAD
Ай бұрын
@@theangrycamper yeah I want to camp it too, so I’m down. I’ll message you
Looks good! Got me thinking I should do mine! Lol
@ATEMOFFROAD
Ай бұрын
Would definitely be a lot more stronger. Maybe the next time you have the axle apart?
Slay 💪
@ATEMOFFROAD
Ай бұрын
Thanks for Watching
While you're in there turn and re-weld the C's, give yourself some caster and a better front driveline angle.
Dude please make a video showing how you installed your headlights and turn signals/running lights I bought the same ones you have using your referral links
@ATEMOFFROAD
Ай бұрын
Will do , find me on IG probably the best way so far. I’m considering sharing the wiring setup on here too. 🍻
👍👍😁👌
@ATEMOFFROAD
Ай бұрын
🍻🍻
Hey mate, what’s the plan with the 44?
@ATEMOFFROAD
Ай бұрын
No big plans , truss and regear , already has locker so good there. 3 months and so much work to do haha👍🏼🍻
what brand are those headlights?
So did you use a high pinion?
@ATEMOFFROAD
Ай бұрын
Yes bought a high pinion from a 95 XJ non disconnect. 🍻