Man great video I was fixing to pull the pan and replace the pump I have a nasty leak over there I will fix at the same time hopefully that gets it my motor just sounded to tight for some bad bearings

Excellent analysis, same happened here and all the thoughts of my 2004 Jeep going to pot! I was in mid ride too and had to do the field diagnostic which told me keep going. Thank you for the work in the vid!

@DarrylSheather

3 жыл бұрын

Hope you sorted the issue.

@boldlionpro2814

3 жыл бұрын

@@DarrylSheather Not finally. At cooler temps and shorter rides where the oil seems to have maintained viscosity, the gauge shows good oil pressure so, it seems well for now. Will consider another weighted oil for engines with over 110000 miles.

Nice one mate.. keep up the good work.

@DarrylSheather

4 жыл бұрын

Thanks!

Great vid. Come through for me twice in last month. My daughter sent me video of her 04 TJ while at idle oil gauge dropped and check gauges alarm pops up. Rev in some and pressure comes up, etc. Going to order the Mopar part and start there. Will follow up.

@DarrylSheather

2 жыл бұрын

Happy to help!

Good video. And the box cutter is just fine👍🏼

@DarrylSheather

Жыл бұрын

Glad you enjoyed it!

Interesting this video turned up in my recommendations today, just yesterday my neighbor called me about his 04 jeep doing this same thing.

@DarrylSheather

3 жыл бұрын

How funny, hope it helps him out.

Thanks

Good info

@DarrylSheather

4 жыл бұрын

Thank you!

Nice vid. It would be nice if you could include a link to the parts you use. It would help others out immensely.

Mine does this and I replaced tge sending unit and it seemed good but on the road it did it again. So I'm taking it in to get checked. I'm thinking it's most likely electrical related.

My 97 has gone through several sensors over the years. I quit replacing them. It must be something electral going on.

Thanks for the video. You have given me a direction to travel. Exact issues here. Box cutters are good enough as if you break the blade you just replace it.

@DarrylSheather

3 жыл бұрын

Glad I could help

It's your boil pressure sensor. Mine did exactly same thing when I bought myb2003 tj. Part was 7 dollars. Then a year later had same issue repalcenoil preasure again. Reason I keep replacing the oil preasure sensor . Is 2003 and up tj run hot and burn the sensors up. I put insulation on this and the crank shaft postion sensore as it was replaced twice as well for same issue. They are very close to each otlf them. Since irreplaceable oil preasure sensor and cranknpostion sensor with insulation to jlkeepnthe heat down on them no issues.

I just picked up a 95 YJ wrangler. 2.5 with the 4 cylinder. It doesn’t go low at all but when you step on the gas the pressure goes to like 80 or so and it doesn’t seem to drop below 30ish when just idles .

@DarrylSheather

3 жыл бұрын

I think they have.a real pressure gauge, so what you describe is totally normal.

@16cliffedge

Жыл бұрын

@@DarrylSheather hey there, my old 98 TJ oil pressure drops by 1 bar / marker at idling. ... plan to sell next week as it happens, could it just be needing an oil change - been sitting for a year or too. Just did 300 miles, was fine

@spencerwarren9219

4 ай бұрын

Oh only use oem oil pr3asure sensor. I went thru 3 of them and then issue was fixed once I bought the oem one. Cost about 40 bucks more but worth it b

Rockauto is awesome !

@DarrylSheather

2 жыл бұрын

it is

Squirt wd-40 in the hole the pressure switch came from also put wd-40 into the switch opening. Junk gets in there and messes up switch

I have a 04 Grand Cherokee with oil pressure gauge issues. Replace the sensor and the wire harness.. still no improvement. Any advise?

@DarrylSheather

4 жыл бұрын

I’d be getting the oil pressure tested with a mechanical gauge so you can at least rule engine issues out. FWIW I had further issues after this video, removed the ecu connectors and sprayed with electrical contact cleaner haven’t had an issue since.

Be sure and get some insulation to cover sending unit to combat the heat or you will be replacing it again in summer when running ac. If temp gets up over 210 degrees it will start to cook that sensor

@warnerherndon205

4 ай бұрын

What do you use to insulate it? I think I need to change mine. Thanks in advance

@spencerwarren9219

4 ай бұрын

@@warnerherndon205 they sale a silver wrap with velcro on Amazon. It isn't much and some autozone carry it also. This has been a issue with all 4.0 tj. Also heat can creat fuel fume lock in injectors and make it idel bad for a little if engine gets hot and you turn it off then start it back up. It's just fuel vapor in injectors inst3ad of fuel. Due to heat burns up the fuel in injector. Doesn't hurt anything just runs like crap for about 45 sec till you get fuel back in injector. Usually happens around 210 temp or above.

Thats not a knife mate... **brandishes a 12 inch kukri** This is a knife!

My car oil pressure light come on at a low rpm for example when I am slowing down or at a complete stop. The oil pressure light turn off at a higher rpm like 2200 rpm for example when accelerating. Do you know what could be the problem, I already change the oil pressure switch & the oil in the engine is full.

@DarrylSheather

4 жыл бұрын

Have a go at disconnecting the loom from the ECU and spraying the connectors with contact cleaner.

@habeeb590

4 жыл бұрын

Darryl Sheather okay👌, can this cause a serious problem to the engine??

@DarrylSheather

4 жыл бұрын

@@habeeb590 yes, if you have low oil pressure the engine can spin a bearing or seize. You need to work through the issue. Best way is to get an all pressure gauge reading straight off the block by a mechanic to see if its mechanical or an electrical issue. Best of luck with it all.

Recently replaced the battery temperature sensor when the P0516 code came up on my '05 Jeep Wrangler TJ cluster. Oddly enough, it doesn't come up on my scanner. This is a first! And when I go in reverse to get parked in my driveway over a very small bump, the check guages light comes on. Also have a new alternator and battery with the battery reading 12.6 when sitting which is perfect. However, the voltage only reads 13.6 after I start it up, when most TJ forums say it should read between 14.2 - 14.7 Any idea of what is causing these things and how I can correct them??

@DarrylSheather

Жыл бұрын

From memory the ECU uses battery temp to determine charge rate. I'd be checking out your connections etc of the battery temp sensor. else replace it with the old one to see if that makes any differences. Maybe it's a faulty new sensor?

@JeepTJWheelin

Жыл бұрын

@@DarrylSheather The check guages light was from a worn out oil pressure sending unit sensor, replaced and works as it should. Getting mixed views from mechanics in my area who say 13.6 is perfectly acceptable while others seem to lean towards 14.2 - 14.7 after the engine is turned over. She starts right up most mornings, but occasionally will have a slight hesitation, peculiar. And had the local garage run a code diagnostic on their much more expensive scanner than what I have. The P0516 came up on theirs, it was cleared, and yet after doing the 3 key ignition turn check, it's still there. Very puzzling to say the least. Connections were checked and everything looks good. I'm thinking the pcu is faulty. I really like these TJ's but miss the absence of computers from the CJ-7.

have this problem on my 98 tj their are telling me it is the oil pump and will cost almost 600 dollars here in the U.S. just paid 36 dollars today November 9th for a oil change and now this problem have too take it in tomorrow.

@DarrylSheather

3 жыл бұрын

Hope it all works out ok for you Robert.

My oil pressire gauge stopped working so i changed this part. Now when i crank the vehicle it still doesn't work on the first crank but oddly enough if i shut off the engine then restart the engine then starts working properly every single time.

@DarrylSheather

2 жыл бұрын

Did you fix that? I’d be doing a oil pressure test with a proper test gauge before going further

What oil filter are you using?

@DarrylSheather

3 жыл бұрын

I try to get the black Ryco versions. Super cheap have them.

Did yours leak out a bunch of oil when you took the old one off?

@DarrylSheather

2 жыл бұрын

Can't say it did

What is the update after a few years? Thanks!!

@DarrylSheather

7 ай бұрын

All good!

Did this solve the issue for you?

@DarrylSheather

Жыл бұрын

Yes

Did this fix your issue?

@DarrylSheather

4 жыл бұрын

had it sporadically afterwards, ended up removing and cleaning the connectors on the ECU with contact cleaner. Haven't had the issue since.

@aguilablanca4x458

2 жыл бұрын

What’s the name of the part?

27m will take it right off

4:55 Why we're here

@DarrylSheather

3 жыл бұрын

Yes!

That's not a knoiffff