Great video, thank you. I want to mention to everyone DO NOT HEAT THE BALL JOINTS, they can EXPLODE. I didn't know this until yesterday.

@johnburson1579

Жыл бұрын

Thank you I didn't know that either. Great tip!

@allmycarsisbroke

Жыл бұрын

Why the heck would anyone want to heat up the ball joints?

I just got a TJ and think I need to do the ball joints. This was a very detailed video and I feel confident being able to do the job at home. Thank you for taking the time and putting in the effort do make these videos. I remember trying to figure this stuff out myself from grainy photos in Clymer manuals back in the day.

Great video. Thanks for taking the time to explain it all.

Thanks for telling the correct torque specifications very helpful.

@TabooCustoms

2 жыл бұрын

No problem!

Excellent video. Thank you for all the helpful info. I’m doing this to a TJ tomorrow and I’ve never worked on this type of vehicle before. Thanks again for sharing

@TabooCustoms

9 ай бұрын

Let us know how it goes. Thanks!

It went as could be expected. But I knew what I needed. Thanks to your video! Thanks again

Good video. I'd add that beginning to soak the nuts with PB Blaster a few times, or other like it, starting a couple of days before, will help a lot toward taking it all apart. I hate wrenching dry rusty nuts. I personally also like to use anti-seize on everything when putting it back together... the bearing mating surface and all threads. If not for future me, then whomever is needing to do this the next time.

Just wanted to say thanks for this video. It was my first time doing ball joints, I used the same HFT tool as in the video (sheer coincidence) and I used it for the universal joints as well. I went back to the video a bunch of times to double check, but by the time I got to the driver's side, I felt like an old pro (it's always easier the 2nd time.) I had way more rust to deal with than your video, but your example and instructions were REALLY appreciated. Subscribing now ... thanks again. (Oh, and thanks for the torque specs!)

Thank you so much for this! I've always avoiding doing ball joints, but this video gave me a bit of confidence!

Awesome video, brother. Perfectly done. Nice and detailed and slow enough to where I could keep up. Lol. Thank you for doing it.

@TabooCustoms

Жыл бұрын

No problem 👍

Thank you for this very educational video, it helped me a lot!

Thanks for a great video. Get yourself a set of aircraft skin wedges. They make the best 'tight space' pry bars. I've been using them for years. They're readily available on Amazon.

Thats surprising that you got the harbor freight to work, I looked on forums and bunch of people are saying you need a special adapter for a jeep

Excellent TY ❤

Thank you for this tutorial!!!

Awesome video. Thanks for the info.

Great video...THANKS!

I like your video hopefully when I do mine it goes as smooth as yours did..

Great tips on this.

Great vid!!!

I believe if you would have had the OTC 7894 cups,you would have had an easier time.The 7894 cups are made specifically for the Dana 30 and 44 axles.👍👍

@blazeboyblazeboy4470

2 жыл бұрын

What's otc stand for?

Wow you popped that loose with a ratchet!

DUDE your bumper stopper is complelty loose in the spring hahahha assuming you know already. great video about to replace my ball joints and tie rod and drag link on my jeep tj 04. why does everyone wire hang the brake caliper, can i just set it aside on a table?

Thanks for the video !!!!

What brand ball joint are you using? I bought Spicer, NWP, G2... and you cannot push from the outside edge's of the bottom, as you show because of the grease boot that instantly tears. I'm $600 into tools and parts on this project after completely snapping a $270 press. I think my axle C maybe messed up, as I had to torch and air chisel the old ones out after 1,200ftlbs wouldn't budge them. I even had a licensed GM mechanic try to remove them, only to give up after 9 hours without any progress recommending that I just replace the entire axle. I've replaced XJ ball joints, JK ball joints, and even CJ ball joints, but this nightmare is something special.

@TabooCustoms

2 жыл бұрын

I dont exactly recall on this one, they could have been Moog or whatever the cheap O Reilly's brand is.

@Matt-416

2 жыл бұрын

@@TabooCustoms hahaha! That's actually hilarious because I just left oriellys. I think I was having issues because I was trying to used knurled ball joints when the OEM were not. Not sure if later TJs had the knurled type, as mine is an '01. Also... She's a Snow-Belt Jeep, so all that salt wasn't very kind to the metal. Thank you for the reply. Keep your tire-side down and enjoy!

@malang724

2 жыл бұрын

@@Matt-416 If you look at the description for "Teraflex 1353000 Heavy Duty Ball Joint Set with Knurling" on quadratec, there's a little blurb about knurling: "These ball joints with knurls (1355300) are for ball joints with a loose press fit in the inner knuckle due to repeated ball joint replacement or if knurled ball joints have been installed in the past. We recommend ball joints without knurls (1355100) as they will not score the inner knuckle and open up the bore." Basically, use the knurled ball joints if your axle is worn out from constant replacement

@Matt-416

2 жыл бұрын

@@malang724 Yeah.. I'm an ignoramus. I didn't realize that there were different types. The jeep has 91k miles and it's the first time they've been changed. The rust and salt corrosion (snow belt) was the issue. Live and learn. I definitely appreciate the response. She's good to go now, aside from waiting on a backordered rear CV driveshaft and I'll be hitting the trails. And I used the terraflex. I'm very satisfied with the quality.

Just a quick question. Can I put a little anti-seize on the new ball joints?

@TabooCustoms

Жыл бұрын

I wouldn't recommend it. You don't want anything that might help it come loose when you don't want it too

@johnjamrowski7505

Жыл бұрын

Ok thank you.

What brand did you use for the ball joints replacement?

@TabooCustoms

2 жыл бұрын

If I remember correctly they were Moog

@JoseOrtiz-eq9yk

2 жыл бұрын

Than you brother for your teaching video

Great video! Torque specs and all!!!