What part number for actuator should be on a Chrysler 300c crd 3.0 2007?
@andret96535 жыл бұрын
got e280 cdi “kangarooing”, fault code 2510 which is turbo actuator, stripped it, solder and gears are fine but i noticed that actuator had been rebuilt before, can it be wrong one then?
@rab28263 жыл бұрын
Is the G number the important number on these when purchasing ??
@rbrood2673 жыл бұрын
I just solder the down two but it didn’t help. Should I solder all the other once as well?
@Peter-wo4uo
Жыл бұрын
Check with a multimeter if there are connections on every wire.
@matthewroxy35282 жыл бұрын
Hi when I switch my engine on and drive I have full boost when I switch off and come back to the car switch on again I have no boost thank the car has gone into lip mold I switch off switch it back on and then I will have full boost what kind of problem be Chrysler 300c Crd 30L
@jordij79743 жыл бұрын
Did you need to recalibrate the actuator once you replaced yours? Or just a straight swap over part?
@johnfeeney4636
3 жыл бұрын
Just as straight swap as long as its the same model
@_wimza_7983 Жыл бұрын
Hi there, i have similar issue where when i floor the car (chrysler 300c crd) the car kangaroo's. Symptoms very similar to misfire on petrol engine but is a diesil. I checked turbo actuator and the gears are spot on, all connections are sturdy so can rule this out. Any other idea where i could be looking?
@darrenbootland2316
Жыл бұрын
Might be worth looking at turbo inlet leaks. The pipe from the airbox to the turbo gets brittle over time and cracks.
@granada0120002 жыл бұрын
Is the code P0046 ?
@danwilliamson97734 жыл бұрын
could be a realy useful video, but no volume at all cant hear a word hes saying.
@kackalovesqhs
4 жыл бұрын
Did you have it on mute? Cause there is plenty of volumn
Пікірлер: 15
Great informative video. Thanks a lot
What part number for actuator should be on a Chrysler 300c crd 3.0 2007?
got e280 cdi “kangarooing”, fault code 2510 which is turbo actuator, stripped it, solder and gears are fine but i noticed that actuator had been rebuilt before, can it be wrong one then?
Is the G number the important number on these when purchasing ??
I just solder the down two but it didn’t help. Should I solder all the other once as well?
@Peter-wo4uo
Жыл бұрын
Check with a multimeter if there are connections on every wire.
Hi when I switch my engine on and drive I have full boost when I switch off and come back to the car switch on again I have no boost thank the car has gone into lip mold I switch off switch it back on and then I will have full boost what kind of problem be Chrysler 300c Crd 30L
Did you need to recalibrate the actuator once you replaced yours? Or just a straight swap over part?
@johnfeeney4636
3 жыл бұрын
Just as straight swap as long as its the same model
Hi there, i have similar issue where when i floor the car (chrysler 300c crd) the car kangaroo's. Symptoms very similar to misfire on petrol engine but is a diesil. I checked turbo actuator and the gears are spot on, all connections are sturdy so can rule this out. Any other idea where i could be looking?
@darrenbootland2316
Жыл бұрын
Might be worth looking at turbo inlet leaks. The pipe from the airbox to the turbo gets brittle over time and cracks.
Is the code P0046 ?
could be a realy useful video, but no volume at all cant hear a word hes saying.
@kackalovesqhs
4 жыл бұрын
Did you have it on mute? Cause there is plenty of volumn