That shop made line borer is genius!

A suggestion .. Shorten your cutting tool and put a grub screw in the back of the tool hole to push the cutter for fine adjustment.

@snowballengineering

Жыл бұрын

Good suggestion, thanks

@markrainford1219

Жыл бұрын

I was thinking there's got to be a better way. My mind was wondering towards another clamp with a 1mm pitch screw to push the cutter forward, but your idea much simpler and better.

@dwarnermg

Жыл бұрын

@@snowballengineering I can’t remember they’re specific name but McMaster car sells threaded square hole inserts for boring bars. Keith Fenner/turnwright machine has part numbers even in one of his videos about boring bars. I think it’s titled “my go to bar”. He’s got some good content he used to do machining in a shipyard.

@mfx1

Жыл бұрын

I'd be concerned about the tool not being held rigidly enough even expensive commercial line borers do it this way so there's probably a good reason.

@zebschreiber7357

4 ай бұрын

@@markrainford1219 I use a similar system for my barrel rifling cutter adjustments, the larger calibers I use a pusher screw below the cutter but the smaller calibers are too small for this to work so for them a built a clamp that clamps on the cutter head and has a dial indicator on the cutter side and a super fine thread pusher screw on the other to push the cutter out I can accurately move the cutter .0003 the most I ever move it out is .0005 any more than that and it plugs my chip box in the cutter head. my line bore I am thinking of doing a similar design but for now I'm just moving it by hand, it's a pain but it works.

Mag drill speed looks fast for the cutting but hey you made it work . Well done 👍

I have often wondered if a mag drill could be made to power a line bore set up and now I know. However, my old Powerbor PB32 is a bit tired for such a task. Top stuff young man. I presume you watch Cutting Edge Engineering (Australia), I C Weld and On Fire Welding? If not, then I can recommend them because they are top channels for repairs, line boring and welding.

@snowballengineering

Жыл бұрын

I do watch them. Them guys are the reason I started making videos myself. Learnt a lot from watching them, hopefully I might be able to share some useful information too.

I like your line borer necessity is the mother of invention cool idea with your grips good way to set the cutter gets the job done you have thought about it fair play to you good job.

@snowballengineering

Жыл бұрын

I can’t take credit for it, I copied it off someone else’s Id seen. There’s a whole community of us with self made line boring machines.

I'm happy to have found your channel you have basically answered all my questions and concerns about using a mag drill for line boring. I need to get my pivot on my tractor repaired has about 3/4 inch of slop in the pivot so it's good to see a mag drill working to drive the line boring bar mine is at least variable speed just have to turn the end and cut the flats for the Weldon coupler. Im just not sure if I should weld up the bearing holes then line bore them or line bore first to make the holes round and over sized and make insert sleeves to fit oem bearings at least this way the next time I have to do this all I need to do is knock out the sleeve and turn another and press it back in not sure what is better i do know that trying to turn welded material can be a problem. Thanks for your videos on this subject.🤔🤔👍👍👍👍🍻

Good one . I used to use an old Bux mag drill , it had a low speed gearbox & auto feed to drive a boring bar . 👍

@snowballengineering

Жыл бұрын

That would of been better. I just used the mag drill we already had.

Very well done! Thanks for the video

A while ago I watched Keith Fenner do some line boring on his lathe. He had some adjustable tool holders in his bar. If you can get hold (or make ) some they would make your life easier when it comes to adjusting the length of the lathe tool. I think they sell them at MSC (USA) but if I can find out the name I'll let you know. He does mention them in one of his vids but I can't locate it. I can probably draw what I mean quicker than I can explain them. Good vid.

Is always nice when things go as planned 👌 👍

I don't know if there is a fixed relationship between the holes you bored and the other pair of holes, but if you had longer plates you could lock into those holes and rest assured you were the correct distance away and only needed to adjust "vertically." You would also be parallel to their centerline if that matters. But good stuff, i enjoyed both videos.

@snowballengineering

Жыл бұрын

That’s a good idea. Would save some time setting up. Thanks for watching!

good stuff man ! glad i found you.

What I want to know is why this lad's only got 93 subscribers... He's got 94 now ☹🇬🇧

@snowballengineering

Жыл бұрын

Only started making KZread videos just before Christmas but I’ll get there slowly 😃 Thanks for the support!

@peterfitzpatrick7032

Жыл бұрын

3 months later and he has 8k... he's getting there, Glen !! 🤗 😎👍☘️🍺

@glennmoreland6457

Жыл бұрын

@@peterfitzpatrick7032 He's a good lad doing stuff right... ☹🇬🇧

This is so entertaining - and educational!!! Thanks!

I have done my share of line boring with b&d,York, climax & several homemade rigs but buddy that’s a nice cut with a mag drill. Looks good .great job

@snowballengineering

Жыл бұрын

Thanks, for the few jobs a year I use it, it works great. If I was to do any more I’d look at getting a proper set up.

One smart guy Could use this for setting bearings in pipes or plates

The inserts are definitely taking a hammering from the heat-affected zone especially as the rpms on the drill are so high... but its working, a bit more refining and you'll have a great system for small money, congrats !! 😎👍☘️🍺

@snowballengineering

Жыл бұрын

I was quite surprised how much the tiny inserts could take. With the new line boring machine I’ve made thankfully they don’t take as much of a hammering.

@peterfitzpatrick7032

Жыл бұрын

@@snowballengineering I'll be checking it out presently... as a new Subber, I'm slowly working through your archives... 🤗 😎👍☘🍺

Nice job !!

that's what i love about machining your imagination is your limitation and a machine set up is safe or it unsafe your going to see it and do it one way i most likely will do it another but in the end was it safe and was it a good job and sir you are a dam good boiler plate machinist

I'm definitely guna try and do this well done for this amazing idea

Your line borer is impressive and very cheap to make, I almost want to make one to try as I already have a mag drill.

Love the ingenuity of the line biting set up, but the mag drill seems to be running much too fast

@snowballengineering

Жыл бұрын

It is a bit fast but it only has one speed.

Great channel. It's like a northern British Cutting edge engineering

@snowballengineering

Жыл бұрын

Thanks!

G’day don’t know if your mag drill has the room but on mine I have a designated plate for the mag drill with a bolt on the side screwed into the magnet of the drill so you can turn the magnet off and it won’t fall. Looks like it worked well though your dial clamp is a nifty idea. I use a digital dial indicator when setting the tool only because it is easier to zero

@snowballengineering

Жыл бұрын

That’s a good idea, I’ll have to see if I can do similar. Digital dial indicator would be a lot easier than mine.

Great job and idea

Gday, new sub here, Max Grant from Swan Valley Machine Shop recommended your channel and glad he did, looking forward to watching more videos, cheers

@snowballengineering

Жыл бұрын

Awesome, thank you!

Perhaps you could have some kind of thumb screw on your tool calibration clamp so that you could set it against your tool before you loosen it then you could tighten it to adjust your tool. This would at least give you a positive stop point to hold the tool against while tightening you grub screw. If that makes sense. I could draw it and maybe make it clearer.

Very nice fit, excellent job..

Serviço top, você e o Kurtis Do canal Australiano CEE, são os melhores.

u get the job done thats all that matters

Nice set up.👍

@snowballengineering

Жыл бұрын

Simple but effective

That's quite a high speed to run those tools at.

@snowballengineering

Жыл бұрын

Yes, too fast, but my mag drill only has one speed

@mfx1

Жыл бұрын

@@snowballengineering you should be able to use an external speed controller, you'll lose a bit of torque but I doubt it will be significant although you mentioned upgrading it so maybe a three phase motor and inverter drive is the way to go.

Genius....

Lower rpm?? Especially the first cut to save you insert. Plus when adjusting the height of the cutter: make it so that when slightly tighting the grub screw that the insert is just a bit low and than tap it to the desired height. Nice job for a custom diy set up

@snowballengineering

Жыл бұрын

Unfortunately my mag drill only has one speed. My next set up I’m going to use an eibenstock motor with 2 gears and variable speed. I’ll do that next time, thanks for the advice.

@therealspixycat

Жыл бұрын

@@snowballengineering do you understand what i meant by tapping the cutter to desired height while it is semi slightly locked? Yes a lower gear would be nice but the cutter is doing a pretty good job cutting all that rough plasma junk.

@snowballengineering

Жыл бұрын

Yes, I understand what you mean, I’ll be doing that next time. Great advice!

@therealspixycat

Жыл бұрын

At 1:31 add an adjusting screw to the bottom of you contraption that measures the insert height. That screw pushes up or keeps the insert at a certain height

hey nice set up! are the cast bearing blocks accurate enough?

@snowballengineering

Жыл бұрын

I haven’t had any issue with them yet. Although the bolt holes aren’t accurate enough to take one off and put back on without having to reline again.

Love the home made line boring kit. You made a quality job of that repair. Just wondering why you don’t bore the holes closer to finished size and just take the last couple of mm out with the line borer? That headstock share had some abuse

@snowballengineering

Жыл бұрын

I like to have plenty of tolerance so there’s no chance of running out of material when boring.

Awesome 😊

How do you center the bar

If the ears where slightly bent outward as you said, how does this affect the line bore?

@snowballengineering

Жыл бұрын

It doesn’t affect it.

Hi. This is a great video and great bit of work. I have been thinking of building the same setup for a while. I bought a bigger drill with slower speed settings. I have yet to get a bar setup. I was thinking 50mm bar but your size would probably be better to start with. What thpe of bar is yours? I would be concerned about welding when the magdrill is connected to the setup as i think it could damage the magdrill. Did you machine the end of the bar yourself to fit the magdrill?

@snowballengineering

Жыл бұрын

Hello. Thanks! It’s a great cheap and effective way of getting the job done. I made the bar myself and yes, i machined the end to fit the same as a standard mag drill cutter. It’s difficult to get the plate the drill sticks to in the right place without having the drill already stuck to it.

@rainbo25

Жыл бұрын

I know what your saying about the plate but you culd fry the circuit in the drill i think. Is it just chrome bar for a hudraulic bar? That what i was thinking of buying and maybe trying to drill the holes with the magdrill myself as i dont have any engineering machinery like milling machine or lathe etc. What would be the maximum size bore you could safely cut with that size bar you are using?

@TheMadHatter626

Жыл бұрын

As long as the welders ground clamp is close to the weld area it isn't a problem. It's when your ground clamp is attached to the work piece at the other end of the shop is when your liable to fry electronics

You can use frequency converter to control the speed, chinese ones from eBay are super cheap.😉

Can you do a video explaining how you had the bar ? I have a mag drill and thinking of doing the same!. I would assume you did it on a milling machine?

@snowballengineering

Жыл бұрын

I turned the end down in the lathe to match the size of a normal cutter and used a milling machine to mill the flats. Also drilled the holes in the milling machine.

Excellent control of your process. I always wondered after repairing a part if I had reached far enough with the welds.

been thinking of line boring this way for a bit. was going to use 20mm bar for 25mm pins u at durham ? fun got the same magdrill. lol

@snowballengineering

Жыл бұрын

It works well. I’m at bit lower than Durham, I’m at York.

Hello, great video, can you tell me what steel the boring bar is made of, I will try to make such a tool myself, because I can't afford to spend about 20k on a new line boring machine Thank you and best regards

@snowballengineering

Жыл бұрын

I just used en8 chrome bar. Nothing fancy. Probably better grades to use but that’s just what I had available.

I made mine too...What is your plan to make bores parallel?

@snowballengineering

Жыл бұрын

Lots of measuring to set reference points

👍

What kind of info can you share on your setup?

@snowballengineering

Жыл бұрын

What info would you like?

@ernielouallen3093

Жыл бұрын

Well I'm thinking about getting into line boring and welding. I have a mag drill already. What kind of boring bar and cutter do you have?

@snowballengineering

Жыл бұрын

@@ernielouallen3093 I made the bar, it’s a bit of 40mm chrome bar. I’m using 8 and 10mm lathe tools for cutters.

@eriknoren6218

Жыл бұрын

Do you think that a bar of Coldplay rolled Steel would do🤔🤔

bagaimana cara pemesanannya alat ini..?🙏

Form 20:22-21:32 it sounds like a Ford.

Почему большие обороты?

Price

Nice line bor. What did you you use to make the bar??

Надо выставлять параллельно другим пальцам. Зачем ты выставляешься по ковшу он может быть кривым ?

🔥🦾

Were you talking to yourself or did you intend for others to hear what you had to say?

You need to talk louder and more clearly