My review of the Hughes Whiplash cam for the Mopar small block 340/360.
Жүктеу.....
Пікірлер: 23
@herbferguson3 ай бұрын
Great video. Looking forward to your 408 build.
@mightydodgefarmsАй бұрын
i can say now i have a 340 stock bottom end stock cam upgraded intake and crarb and it ribs its been rebuilt once all oem and it is awsome it just eats 4 speed to tear the rear tires up
@gregleenyit3 ай бұрын
Sounds good!
@Awiththejuice1443 ай бұрын
Please do a video about your 46rh transmission swap!!! I plan on doing the same to my 81 d150
@WrecklessEnterainment
3 ай бұрын
Sounds good! I should be able to make something for it! Surprisingly was a really easy swap.
@WrecklessEnterainment
2 ай бұрын
Went ahead and just uploaded a video about the transmission for you. Hope it answers some of the questions you had!
@michaelhoneycutt7138Ай бұрын
They say is works good off the bottom end. I am looking for a lower torque motor. I rip a bit. Looking to put one in my Dakota. But I want to be able to use it.
@daddysbrokegarage
Ай бұрын
Put a lower gear in. 3.55 even is a great road gear
@WrecklessEnterainment
Ай бұрын
@@michaelhoneycutt7138 I believe the 5.9/5.2 magnum roller whiplash cams are a lot more mild than the flat tappet version so if you have a roller motor it might still be a good option.
@AshMyBuck3 күн бұрын
Anyway I could get in contact with you? I’m building a 360 magnum for my 88-d150 and I’m kinda looking for some guidance. It would be greatly appreciated.
@WrecklessEnterainment
3 күн бұрын
@@AshMyBuck what are you looking to do with it exactly?
@loganlowry710214 күн бұрын
What size pipe and mufflers did you use? I’ve got a 318 with the whiplash cam that I’m building
@WrecklessEnterainment
14 күн бұрын
@@loganlowry7102 it’s just got a set of 12” resonators and 2.5” pipe
@loganlowry7102
7 күн бұрын
@@WrecklessEnterainmentnice, it sounds great. I’ve got some 3 inch pipe and magnaflow mufflers. Hopefully it’ll sound good
@kennethcox96883 ай бұрын
I like the seats and steering wheel! What transmission do you have in it?
@WrecklessEnterainment
3 ай бұрын
It’s a 46RH. It’s from a 95 Dodge Ram with a 5.9 magnum. It’s been great! It’s basically a 727 with over drive and a lock up converter.
@wearegame7773 ай бұрын
I wish I could find someone running a big block Steamroller hydraulic roller cam...
@WrecklessEnterainment
3 ай бұрын
I’ve got a 408 stroker I’m putting together I’m going to use one of their steam roller small block cams.
@joe-hp4nkАй бұрын
What are the specs? Thanks.
@WrecklessEnterainment
Ай бұрын
@@joe-hp4nk 223°/236° @.050, .506/.515 lift and 107° lobe sep.
@joe-hp4nk
Ай бұрын
@@WrecklessEnterainment That's a nice cam for 9 - 10 to 1 cr. The 107lsa is the best part. Be nice to know what the cylinder pressure is.
@WrecklessEnterainment
Ай бұрын
@@joe-hp4nk it’s cut for low compression engines and is made to close the intake valve early and increase the cylinder pressure. I believe they say 8.6:1 is the max they recommend on it. Works great for a stock low compression engine! My 360 was around maybe 8:1 and I even ran regular fuel in it sometimes.
Пікірлер: 23
Great video. Looking forward to your 408 build.
i can say now i have a 340 stock bottom end stock cam upgraded intake and crarb and it ribs its been rebuilt once all oem and it is awsome it just eats 4 speed to tear the rear tires up
Sounds good!
Please do a video about your 46rh transmission swap!!! I plan on doing the same to my 81 d150
@WrecklessEnterainment
3 ай бұрын
Sounds good! I should be able to make something for it! Surprisingly was a really easy swap.
@WrecklessEnterainment
2 ай бұрын
Went ahead and just uploaded a video about the transmission for you. Hope it answers some of the questions you had!
They say is works good off the bottom end. I am looking for a lower torque motor. I rip a bit. Looking to put one in my Dakota. But I want to be able to use it.
@daddysbrokegarage
Ай бұрын
Put a lower gear in. 3.55 even is a great road gear
@WrecklessEnterainment
Ай бұрын
@@michaelhoneycutt7138 I believe the 5.9/5.2 magnum roller whiplash cams are a lot more mild than the flat tappet version so if you have a roller motor it might still be a good option.
Anyway I could get in contact with you? I’m building a 360 magnum for my 88-d150 and I’m kinda looking for some guidance. It would be greatly appreciated.
@WrecklessEnterainment
3 күн бұрын
@@AshMyBuck what are you looking to do with it exactly?
What size pipe and mufflers did you use? I’ve got a 318 with the whiplash cam that I’m building
@WrecklessEnterainment
14 күн бұрын
@@loganlowry7102 it’s just got a set of 12” resonators and 2.5” pipe
@loganlowry7102
7 күн бұрын
@@WrecklessEnterainmentnice, it sounds great. I’ve got some 3 inch pipe and magnaflow mufflers. Hopefully it’ll sound good
I like the seats and steering wheel! What transmission do you have in it?
@WrecklessEnterainment
3 ай бұрын
It’s a 46RH. It’s from a 95 Dodge Ram with a 5.9 magnum. It’s been great! It’s basically a 727 with over drive and a lock up converter.
I wish I could find someone running a big block Steamroller hydraulic roller cam...
@WrecklessEnterainment
3 ай бұрын
I’ve got a 408 stroker I’m putting together I’m going to use one of their steam roller small block cams.
What are the specs? Thanks.
@WrecklessEnterainment
Ай бұрын
@@joe-hp4nk 223°/236° @.050, .506/.515 lift and 107° lobe sep.
@joe-hp4nk
Ай бұрын
@@WrecklessEnterainment That's a nice cam for 9 - 10 to 1 cr. The 107lsa is the best part. Be nice to know what the cylinder pressure is.
@WrecklessEnterainment
Ай бұрын
@@joe-hp4nk it’s cut for low compression engines and is made to close the intake valve early and increase the cylinder pressure. I believe they say 8.6:1 is the max they recommend on it. Works great for a stock low compression engine! My 360 was around maybe 8:1 and I even ran regular fuel in it sometimes.
😎🤘🏆🏆🏆