iot smart energy meter using nodemcu esp32 with Blynk app | iot projects using esp32 #iotproject
Ғылым және технология
This video is about how to make iot based smart energy meter using esp32 with Blynk app
The current Sensor and voltage Sensor measure the load current and voltage..it also calculate the power and total power consume in kwh ..by Emonlib library..the data stored in esp32 EPROM Memory......
Energy meter program code : drive.google.com/file/d/1F7lbGMbMxKOWTLZGngLzqxiOilm7NH9n/view?usp=sharing
I2C Address program code : drive.google.com/file/d/1G_ktCh0d0uZQK7-KkvTX86kHolwcDvyM/view?usp=sharing
Emonlib library : github.com/openenergymonitor/EmonLib
pin diagram : drive.google.com/file/d/1_SKUrUhx6mGfppO3rvCqCFuAxYFPro1u/view?usp=share_link
Follow on Instagram : research_tamil_an?igshid=MzMyNGUyNmU2YQ==
#iot #esp32 #diy #blynk #electrical #electronic #nodemcu #finalyearprojects #eee #energymeter #miniproject #electricalengineering
Пікірлер: 178
Hello sir I have a one doubt in this project Can I use esp8266 instead of esp32 board?
@researchtamilan4106
Жыл бұрын
Noo...
Which battery can be used to power the above ciruit. We are using esp32 with 38 pins containing only v5 pin and no vin pin
@researchtamilan4106
Жыл бұрын
Esp32 operating 5v input
@mintamerinjacob5114
Жыл бұрын
Will 2 li ion battery can be used by regulating voltage to 5v
@researchtamilan4106
Жыл бұрын
One Li on battery is 1.2v or 3.7v
Super bro ❤️
Bro I cant understand. Why it shows 4watts only. Its looks like youre using 60w incandescent lamp. Than why it shows only 4w.
Useful video anna
@researchtamilan4106
Жыл бұрын
Thank you brother
Nice teaching brother
@researchtamilan4106
Ай бұрын
Thank you bro
sir, about 2 wires on ac current sensor which are red and white. so do you know the lables?
@researchtamilan4106
10 ай бұрын
Are you asking terminal connection of current Sensor
@mrz2245
10 ай бұрын
@@researchtamilan4106 yes sir
bro blynk app different node mcu control panna mudiyuma? for example hall ku oru node mcu iruku and bedroom ku oru nodemcu iruku so these 2 va naa ore blynk app la use panna mudiyuma
@researchtamilan4106
Жыл бұрын
Ella oru nodemcu ku oru Blynk dashboard than use panna mudiym...but you can use two.. baseboard on blynk
Hey bro when we upload your code it says error. Is it updated or there's some code that we add or replace?
@researchtamilan4106
5 ай бұрын
What is the error?
Hello sir I have a one doubt in this project I have a esp32 board 38 pin type Your board is 30 pin type How can I change the pin number in programming
@researchtamilan4106
Жыл бұрын
Give the connect as per Circuit diagram...and check....
hi sir, i connect the esp32 but the voltage and current still reading, but i dont put the voltage and current sensor yet.
@researchtamilan4106
10 ай бұрын
Initially it shows unknown value.. connect load and check
@mrz2245
10 ай бұрын
@@researchtamilan4106 alright tq for your info
@mrz2245
10 ай бұрын
@@researchtamilan4106 also i want to ask about that ac current sensor. it has 2 wire which are red and white. do you know the labels?
please nothing is displayed on the screen; however my I2C usually works with the code (0x27, 20,4)
@researchtamilan4106
Жыл бұрын
Adjustable the potentiometer in i2c Module in back side
The current sensor shows a reading of 0 always. Is there any solution?
@researchtamilan4106
11 ай бұрын
Check that current Sensor is showing value....and check connection
brother i am doing same project with micropython ESP32 unable to do it current,power,voltage values are not changing please guide me
@kesavan-x2s
22 сағат бұрын
kzread.info/dash/bejne/X5Vt0MWRdaeWYbA.htmlsi=z7Mqd6p5GMhZy3WM
Hlo bro You did a nice presentation. You used 20×4 lcd display instead of that we can use 16×4 lcd display bro. If you use that also we need to connect the i2c module aa bro
@researchtamilan4106
7 ай бұрын
Yes you want to use i2c and want do some modifications on program
olá, ótimo projeto, vc pode me ajudar, como eu poderia colocar uma linha de comando para calcular os gastos de energia? aproveitando o mesmo programa.
@researchtamilan4106
7 ай бұрын
These work is based on programming.. Based on the energy consumption have set cost in program
How can i connect the bulb? Looks like theres two sets of wires
@researchtamilan4106
Ай бұрын
Connect phase and neutral direct with voltage sensor
Sir,When we place 60watt bulb it show correctly but when we placed the 100 watt bulb it is not showing 100watt it is showing 60watt itself
@researchtamilan4106
Жыл бұрын
Watts is a power = VxI ...in 100w the current is o.43A and voltage is 230v..
@mintamerinjacob5114
Жыл бұрын
When the 100watt bulb is placed current becomes 0.26 and 60 watt bulb is placed current remains 0.26 .
@researchtamilan4106
Жыл бұрын
Check the current Sensor connection..or try if change the calibration value in program
@mintamerinjacob5114
Жыл бұрын
Connection is as per the diagram. Actually how we can calculate the calibration factor
Sir We connected Same as per Circuit Diagram,But Voltage Reading is not showing 230v but it is showing 104V
@researchtamilan4106
Жыл бұрын
Adjust the potentiometer in voltage sensor
@meghanasangapur9700
Жыл бұрын
@@researchtamilan4106 Thank you Sir
@researchtamilan4106
Жыл бұрын
Ok
Present sir
hi can we configure it as bidirectional meter
@researchtamilan4106
10 ай бұрын
No
Voltage realy direct ah supply kudutha on aguma illa esp32 ku supply kudutha on aguma
@researchtamilan4106
9 ай бұрын
220v voltage sensor kudukanum .5v esp32 kudukanum
If you don't multiply the Power with the Power Factor, your Energy readings will be wrong.
Shei hoise vai
@researchtamilan4106
11 ай бұрын
Yes
Will this work with circuit breaker?
@researchtamilan4106
Жыл бұрын
Yes it's measure the flow of current..
Your Esp is not compatible with LiquidCrystal-I2C library " This is my error and so that i can't see values in LCD and also in mobile i can only see voltage reading current and voltage I can't see?
@researchtamilan4106
8 ай бұрын
Are you find your adress of i2c lcd display
@pravin4372
8 ай бұрын
Yes 0x27. Now I modify adafruit_liquidcrystal library in my code and that I don't receive any error. But my lcd display not showing any texts even though i adjust in I2C . And Blynk also I can only see Voltage reading. Power I can't see?
@researchtamilan4106
8 ай бұрын
Connect esp32 with wifi
@pravin4372
8 ай бұрын
Yes I connected it will be visible in my phone esp32? what can I do??
@researchtamilan4106
8 ай бұрын
Connect the load and check
Bro current sensor connection not working? What should I do bro? Please reply
@researchtamilan4106
5 ай бұрын
Check your cathode and left terminal connection is correct?
Hello, I need help on how to connect the resistors and capacitor to the current transformer. Please, I need this as soon as possible. Can I contact you, please?
Bro energy management system venum bro plz video podunga
@karthickkarthick7872
5 ай бұрын
Using iot
Bro suggest any final year smart grid project.
@researchtamilan4106
11 ай бұрын
Ioi based electricity theft detector
@stephena.v2281
11 ай бұрын
@@researchtamilan4106 thank you
How to connect voltage sensor to esp32?
@researchtamilan4106
5 ай бұрын
Connect line pin in entered GPIO pin or circuit diagram link in discription
Bro I make this circuit voltage show on monitor but current not show I use 30 A current sensor
@researchtamilan4106
10 ай бұрын
Check current Sensor connection
@9Noman
10 ай бұрын
Brother voltage current power and kwh show in arduino idl serial monitor but not show in blynk app .blynk app show online connected some time voltage show only.
@9Noman
10 ай бұрын
Measure value not show in blynk gauge
@researchtamilan4106
10 ай бұрын
Check virtual pin correctly in Blynk app
@k.narasimha9577
6 ай бұрын
Bro, you got solution for this problem or not.
Sir, Can i get reading on LCD when WiFi is not available ?
@researchtamilan4106
26 күн бұрын
Check your SSID and password are correct also turn on your hotspot the esp board automatically connect to your mobile
@0124akash
26 күн бұрын
@@researchtamilan4106 sir, am asking wifi not available, I get reading on LCD?
@researchtamilan4106
26 күн бұрын
Which Microcontroller are you using?
@0124akash
26 күн бұрын
@@researchtamilan4106 ESP32
Bro please tell itha mari 3 phase ku panna mudima with blynk app
@researchtamilan4106
Жыл бұрын
3 phase connection la kuda...1 phase la erunthu 230v..than varum...bro
@ranjithkumar.s3657
Жыл бұрын
@@researchtamilan4106 bro yenaku 3 phase la um power iruka illa 2 phase tha irukanu blynk app la theriyanum Apadi panna mudima
@researchtamilan4106
Жыл бұрын
Only on one phase reading will show
In blynk application my device is not getting online 😢any solution please
@researchtamilan4106
Жыл бұрын
Enter the autho token correctly
@userferdinand
Жыл бұрын
@researchtamilan4106 Bro i have entered many times but its not connecting
@researchtamilan4106
Жыл бұрын
Are you upload the program correctly in esp32
Bro what is the use of resistor and capacitor in this circuit
@researchtamilan4106
8 ай бұрын
It is a divider circuit
@allanpaulAN
8 ай бұрын
It showing.....Exit status 1 error compiling for board nodemcu-32s
@researchtamilan4106
8 ай бұрын
Change the Blynk version
Bro capasitor full value sollunga
@researchtamilan4106
4 ай бұрын
63v 10uf
Explain me about the wiring plz
@researchtamilan4106
9 ай бұрын
Check connection in discription
Template id and template name ah specify panna solluthu bro enga specify panrathunu therilaaaa
@researchtamilan4106
28 күн бұрын
No need to add that is for your compiling error check your proper port and board
Bro total ha ella components vanga evlo selavachi
@researchtamilan4106
3 ай бұрын
Approximately 2000rupess
Bro eanaku oru help Ungalala pana mudiuma Esp32 use panni oru project pananum bit programing teriyadhu konjam help panamudiuma
@researchtamilan4106
Жыл бұрын
Yes ..say your project
@vasanthakumar2368
Жыл бұрын
Thank you for your replay Na enoda bike ku konjam altration panalam nu irukean bro Enkita hf deluxe bike dhan iruku so adhula iruka analog spedometer and petrol meter ellam eaduthutu old mobile phone use panni bike total control aum voice muliyama control panalam nu plane panitukeam eanaku hardeare problem illa adha na ready panipean but software dhan problem
Anne nice presentation plz sent me the flow chart
@researchtamilan4106
9 ай бұрын
Thank you
@thevanrajsivakumar8286
9 ай бұрын
Flow chart?
@researchtamilan4106
9 ай бұрын
So far I didn't not make flow you can write flow chart as per the video flow..
@thevanrajsivakumar8286
9 ай бұрын
@@researchtamilan4106 tq
@thevanrajsivakumar8286
9 ай бұрын
@@researchtamilan4106anna sct103 ku proteus libary irukka
Bro components la enga online la purchase pandradhu nu solunga
@researchtamilan4106
Ай бұрын
Filpkart or Amazon bro
Lcd is not showing anything sir
@researchtamilan4106
Жыл бұрын
Find your i2c address...after adjust the potentiometer in i2c Module
@sumeetshirsat4450
Жыл бұрын
@@researchtamilan4106 thankk youu so muchh sirr, your video helped me a lot, i made this for my final year project...helped a lott sirr🙏🙏
@researchtamilan4106
Жыл бұрын
Basically I am only say thanks for you...to watch my video 🙏. Do more projects and we'll......👍
Nice video! can you send me the flowchart of this projects?
@researchtamilan4106
Жыл бұрын
Yes...
Hi bro can you please guide me about the i2c Address...?
@researchtamilan4106
6 ай бұрын
To communicate with I2c protocol you need i2c Address..
@user-gq6ml3jb8y
6 ай бұрын
@@researchtamilan4106 how I can get that address?
@user-gq6ml3jb8y
6 ай бұрын
@@researchtamilan4106 can you explain the whole video of that project in English or Hindi ...
Can u provide me a block diagram 😢
@digantobiswas
6 ай бұрын
You can find block diagram in this video. Follow 17.32 minute screen.
energy meter using plise - من فضلك
@researchtamilan4106
Жыл бұрын
Text in English language
working fine but irms not accurate
@researchtamilan4106
Жыл бұрын
Change the calibration value 8n program
esp32 ku add pandra 3 url link pls bro
@researchtamilan4106
2 ай бұрын
arduino.esp8266.com/stable/package_esp8266com_index.json dl.espressif.com/dl/package_esp32_index.json raw.githubusercontent.com/espressif/arduino-esp32/gh-pages/package_esp32_index.json
@researchtamilan4106
2 ай бұрын
arduino.esp8266.com/stable/package_esp8266com_index.json dl.espressif.com/dl/package_esp32_index.json raw.githubusercontent.com/espressif/arduino-esp32/gh-pages/package_esp32_index.json
Bro the i2c address program code link says it does not exist. Please check as it is very urgent
@researchtamilan4106
Жыл бұрын
Check are you select the port and board is correct..
@akashbera160
Жыл бұрын
@@researchtamilan4106bro what I'm saying is there is some error in the link you have uploaded in the description for i2c address code. Do check the link you have uploaded
@researchtamilan4106
Жыл бұрын
Yes wait I will re upload it
@researchtamilan4106
Жыл бұрын
Now you check bro
what's the problem? LiquidCrystal_I2C lcd(0x27, 20, 4);
@researchtamilan4106
Жыл бұрын
Enter your I2C address...on program
Bro output varamattagathu
@researchtamilan4106
2 ай бұрын
Check the connection once again
Bro Naa some doubts unga kitta clarify pannanum so eppadi Naa ungala contact pannuradhu plz 😢
@researchtamilan4106
5 ай бұрын
In Instagram
@THARUNKSECE-B
5 ай бұрын
Bro indha output ah Naa eppadi spreadsheet la poduradhu bro. @@researchtamilan4106
Bro enaku power katala
@researchtamilan4106
2 ай бұрын
Are it shows voltage and current parameters
Hello brother code compile not work
@researchtamilan4106
10 ай бұрын
Select correct port and board
@9Noman
10 ай бұрын
Brother how to use i2c program code
@researchtamilan4106
10 ай бұрын
Upload the given code in esp32 open serial moniter
@9Noman
10 ай бұрын
Any related video ?
@9Noman
10 ай бұрын
Bro first i2c program code upload in esp32 then main program upload in esp32
power not accurate
@researchtamilan4106
Жыл бұрын
Multiple the voltage and current
Nice video, blynk not connect
@researchtamilan4106
Жыл бұрын
Thanks enter you token in program
@chennaicraft7556
Жыл бұрын
@@researchtamilan4106 i do but not working
@researchtamilan4106
Жыл бұрын
Connect with mobile hotspot after Blynk show online status
Not good project,do try this home
Please specify your blynk_template id and blynk template name nu error varuthu bro Enna bro pandrathu
@researchtamilan4106
11 ай бұрын
Blynk auth token enter panigala.....athuku mala..Blynk template I'd and Blynk template name.. copy panni paste panuga... Blynk app la erunthu
@SowntharD
11 ай бұрын
Thank you bro ❤️🫂
Sir can you provide your Instagram link again it's not valid in description
@researchtamilan4106
8 ай бұрын
Now you can check
Bro your number
@researchtamilan4106
10 ай бұрын
You can contact in Instagram
Bro ella component link um kedaikuma?
@researchtamilan4106
8 ай бұрын
You can message in Instagram