Intex Seahawk 4 Motor Mount Wheels / Transom wheels
Тәжірибелік нұсқаулар және стиль
Just wanted to show my idea of making the transom wheels of my inflatable boat.
I appreciate much for putting a little of your time on watching my videos.
Please consider hitting the red SUBSCRIBE button and the thumbs-up sign, and I would be grateful and happy for doing so.
=============================================================
Music from Uppbeat (free for Creators!):
uppbeat.io/t/reakt-music/deep...
License code: KEODNMCQSXDTMPR0
Пікірлер: 47
Amazing explanation of what , how and why. Thank you so much for the honky tonk guitar rifs. I will have my boat in the water in NO TIME.
@cesar8359
8 ай бұрын
Thanks for watching
Congratulation. Very clever Idea,
@cesar8359
11 ай бұрын
Thanks for watching
Nice work
@cesar8359
7 ай бұрын
Thanks for watching
Omg 😮 I love it 😻
@cesar8359
Жыл бұрын
Thanks for watching
I like it! cool!
@cesar8359
2 жыл бұрын
Thank you, I appreciate much.
Good job
@cesar8359
2 жыл бұрын
Thanks for visiting my friend
good review
@cesar8359
2 жыл бұрын
Thank you 😊
👏👏👏👏👏💯 showwww
@cesar8359
2 жыл бұрын
thanks for watching my friend
แวะมาทักทายให้กำลังใจกันและกันจ้า Hello dear friend nice 👍 to meet you
@cesar8359
2 жыл бұрын
Nice to meet you too and thank for watching my friend
@sakolvoradee
2 жыл бұрын
You welcome dear friend thanks 🙏
Great work! Thanks for sharing. Can I ask what size of U rings did you use that fitted the original screw holes so well?
@cesar8359
2 жыл бұрын
Thanks for watching. The size of the U rings were 1/4 inch by 6 inch.
Bigger wheels would have done the trick......I'm using 11in wheels from an old bused lawn mower.....good vid
@cesar8359
Жыл бұрын
Thanks for the advice and for watching
Very nice. What size of the aluminum square pipes did you use?
@cesar8359
11 ай бұрын
1x1 inches. Thanks for watching
@dmytrobryushkov
11 ай бұрын
@@cesar8359 Thanks a lot
Great idea but much more practical and stronger with the floor in and other item's inside it to make a dolly/cart. Have you made a dolly for it yet?
@cesar8359
2 жыл бұрын
You're right Mark dolly cart would be much stronger but I haven't made a dolly yet
@markweatherall7437
3 ай бұрын
@@cesar8359Just a thought, 10" wheels would be better I think because it would raise the stern of the boat higher.
@cesar8359
3 ай бұрын
@@markweatherall7437 thanks for the tip, it's a good idea but my boat has been punctured and can't be repaired that's why I switched to kayaking.
Neat idea. It would be much better with some very simple directions/sketch/dimensions or, at least, a list of materials you used, Ce sar. Much more valuable if I could build it. As is, I wouldn't even try - I'm not that good! Thanks.
@cesar8359
2 жыл бұрын
Thanks for the suggestion Jack appreciate it much.
@markweatherall7437
2 жыл бұрын
Make a Dolly instead, much better.
Hello keep safe.its me eto po sukli ko...full pack sato.God bless
@cesar8359
2 жыл бұрын
Salamat po at God bless din and stay connected po
Hi, what is the size of aluminium profile ? I want to create the same gadget for my Mariner 4.
@cesar8359
Жыл бұрын
1 x 1 inch aluminum tubing, thanks for watching.
I have the Intex three and for some reason it’s losing air in the outer chamber every couple hours. Do you experience the same? It may be just an air molecules issue. Thanks mate
@cesar8359
2 жыл бұрын
No, I haven't experienced that issue mate
@xykkkk
Жыл бұрын
I experienced similar issue with mariner 3 and took quite a while to figure it out. Most of leaks happen along the vertical seams. you may find these leaks using soapy water. They are very very small, the diameter of each bubble may be less the 1/4 millimeter. dozens bubbles show together after 1 min with soap water at leaky point. I fixed about 100 +/- such leaks using LOCTITE Vinyl, Fabric and Plastic glue. AirStop also work, but much more expensive.
New subscriber here. Is it possible if you could share the materials you have used to this nice and very simple transom wheels you have made? I truly appreciated if you could. please and thank you.
@cesar8359
Жыл бұрын
Thanks for watching and for subscribing, appreciate it much 🙏. The materials I used were a 1x1 aluminum tubing, 3/8 × 2 3/4 nuts and bolts, plastic wheels, 1/4 × 4 U bolts with nuts and locking pins
@subicbay100
Жыл бұрын
@@cesar8359 thank you so much. Take care ❤ bro.
🤣