5:50 is when the build itself starts. *BEFORE YOU COMMENT BELOW, CONSIDER THIS FAQ* *Where can you buy this kit? Link for the [Insert single part here]? Where can I find parts?* Google search "Honda GX200 Electric Start Kit", below I have linked some results www.ombwarehouse.com/electric-start-kit-gx200-and-196cc-clone-aftermarket-replacement.html www.amazon.com/Electric-Flywheel-Starter-Switch-Ignition/dp/B07VF4Y25Q www.ebay.com/p/1562997975 *For HEMI* www.vpowerequipment.com/predator-212cc-electric-start-kit-60363/ *Can this work for a **____* This tutorial is designed specifically for the Predator 212, Honda GX160/200, and similar clones. If you have a different engine, it' is high chances that it will, but assembly will be different. Otherwise: *No*. *Will this work for a HEMI Predator 212* Refer to the question above, BUT, there are kits out there made for a hemi. *What [sized] battery should I use?* This kit is wired for 12 volts, and the starter box comes with a 10amp fuse. I currently run a 12v 8.5aH battery and it starts just fine. *Is a battery needed?* If you don't want the electric start, no. *Does the coil(s) charge the battery?* Yes. Idle is at about 12.5 volts. Under running RPM's in a governed 212 it's >= 13V For any future questions, you are free to join my discord here and ask them! discord.gg/yy9wvHD

The kit I just received, comes with a new shroud and has the correct cutout for starter, so No cutting! 😀 I stopped by to follow your video before I installed my kit today! THX!

@curtisyastic4130

2 жыл бұрын

Do you have a link to the exact one you bought?

Young man.. You are the reason KZread is awesome... Keep doing what you are doing...

@NiTecIndustries

4 жыл бұрын

Gunnslinger777 I appreciate that!

*IMPORTANT: It would be highly recommended to use a thread locker on the internal bolts for the coil and solenoid.* Unfortunately, after doing a ride for an hour, one of the bolts holding the starter loosened and ejected out of the engine, causing the cast aluminum piece to crack, and misaligned the gears when starting. Pull starting is okay, but not electric start. The bolts were tightened snug shown in the video. PS. *THANK YOU FOR 70,000 VIEWS. LETS GET TO 100,000???* Much love!

Thank you for the video. The wiring section was very helpful. Well done.

Awesome tutorial. I will be coming back to this for my build. Thanks for sharing!

Thank you! I might be doing this in the future and I love the detail.

Can’t thank you enough for this video. I got my kit installed today though mine had different parts. They included all bolts and hardware and a new flywheel cover that covers the starter! Thanks again, especially for the wiring section!

@NiTecIndustries

3 жыл бұрын

David Vanmeter Glad to be of service!

@tylerpeters2862

3 жыл бұрын

Do you have a link to get the parts

@NiTecIndustries

3 жыл бұрын

tyler peters Google search: Predator 212 charging coils or Honda GX200 charging coils, or use the links in the description.

Thank you; it's a great vid and helped smooth out the installation. The video from the company doesn't hold a candle!

Pretty cool to see The C & C sticker on the shroud.. 👍👍.. Thanks for the detailed video..🍻🍻

Very good video, Thanks for posting it

I'm so glad I found this video, now I'm going to be replacing my old golf cart motor with an 8hp predator and I can have electric start 😊

Awesome video. Thanks!

Hey little Dude, This was an excellent tutorial! I intend to install an additional coil and and electric start on my Honda GX160 for my Bartell Power trowel. Importantly, the tools required, possible difficulties, the step by step process, and parts list was very handy. I've seen a number of videos so far, but yours is the best. YOU ROCk young man, great Job!

@NiTecIndustries

3 жыл бұрын

Thank you so much!

Thank you for this helpfull Video.

Gotta say I love the it'll be fine sticker

Useful info. Instant sub!!!

Thanks for sharing

Finally someone who shows the same kit I have. Couldn't figure out the yellow green wire. Only in China use something other than black for a ground wire. Lol

Lead and brass hammers are your friend. Preferably lead. They won't beat the crank threads up like a steel head hammer.

awesome video

I've got a golf cart I'm putting a predator 212 In thank you for the help

Thank you

Thank you for this detailed and very informative video! I would like to correct you on one bit of terminology; you say "O-ring connector" but the correct name for the part is "Ring-Tongue Connector". O-rings are typically rubber rings that are used to seal pipe fittings. Cheers!

@NiTecIndustries

3 жыл бұрын

Lol, I could've sworn i've said "Ring Terminal" or equivalent, but thanks for the education; I already knew what O-Rings were used for prematurely.

This looks like it could be worth the money for my CTU200EX

Hellz yea

Great video and great manual. I liked and subscribed!! awesome channel!

@NiTecIndustries

4 жыл бұрын

CSJiGSaW08 Glad to help!

I use a impact driver on the crankshaft nut all the time lol

@bowlweevil4161

3 жыл бұрын

impact for taking nut off, but torque wrench to put it on

👍👍

Fyi the honda 5.5 gx160/ pred212 kit fits the durostar 4000s perfectly also, same block. Same mount holes, durostar will not tell you this.. they say there isnt a kit made and you have to buy a generator with one already on. It..

First off, the video is very useful, thank you! Second, the plastic shroud not fitting, when bolted all back on it sounds like it grinds on the pull start casing. Did this happen with you?? Did you grind the knobs down?.

@NiTecIndustries

4 жыл бұрын

Mario Giannini Yes. The factory plastic shroud is not compatible; I even noted it and you can SEE it in the video (Timestamp 9:54). I ground down one of the three knobs, because two of them fit. Hope this helps; I’m glad I could help otherwise.

Thanks for this video, it's great! If I don't need the battery to be charged, can I omit the charging coil altogether? If so, does that wire just get terminated? I'm preparing to do this for a generator, thanks again!

@NiTecIndustries

2 жыл бұрын

If the generator will charge the battery then sure.

This may be a stupid question... But does the engine recharge the battery as it runs? Or does one have to keep the battery plugged into a tender?

Nah in the intro I thought someone was calling me 💀

excellent video, I would like to know where I can get that flywheel and the charging coil, and what kind of starter is used. Thank you

@NiTecIndustries

3 жыл бұрын

Glad to be of service! You can look in the description or search either a, predator 212 electric start kit, or use the direct kit that this is based off of. This is basically a Honda GX 190/GX 200 electronic starter kit. You can find it on eBay for the inexpensive price. Hopefully it helps.

Just found this video while doing a google search, as I have a predator 212cc motor on my little duck hunting boat. It can be a nightmare to pull start when its cold out hunting in the fall.....Great video, and Ill be referencing it once I get my kit! Question though, is the Electric start kit you linked to amazon under the video, the same kit that you used? I want to make sure before ordering it for my Predator 212! Thanks!!

@NiTecIndustries

5 ай бұрын

It “should” be, yes. It was the link on my gift wish list when my dad got it. If you can find a kit cheaper for a Honda GX200 clone elsewhere that will also work too, long as it’s for a non hemi motor (aka the flywheel bore isn’t tapered)

Thank you for the detailed video! I just did mine but it seems to take a few tries before the engine starts. Battery is brandnew with 180 CCC so no problem there. I do notice the gear on the starter solenoid doesn't quite line up with the gear on the pulley? Could this be the problem? Do these gears have to interlock with each other?

@NiTecIndustries

4 жыл бұрын

Mary H If you meant the gears on the flywheel they should? Does it crank up like mine did in the video? Something must be weak or there’s something internally causing friction with the engine.

@BAONGUYEN-uh2ly

4 жыл бұрын

@@NiTecIndustries Yes I meant the gear on the flywheel...should it interlock with the gear on the starter?...mine looks like they didn't completely interlock but I did try to push the flywheel in as far as I can ..even pounding it with a rubber mallet. the engine doesn't start right away...it takes at least 3-4 turns of the key .

@NiTecIndustries

4 жыл бұрын

Mary H Then that’s the problem then

@BAONGUYEN-uh2ly

4 жыл бұрын

@@NiTecIndustries Ok I went over it last night. I double check the flywheel is as far in as possible. The gear on the starter is not engaging with the gear of the flywheel until you turn the key...then it pops out and engaged the flywheel gear and pop back when you release the key. Kinda makes sense because you wouldn't want the starter gear to keep spinning when the engine is running...right? I checked the spacing of my ignition coil and looks like one end is slightly out too far so I readjusted it to proper spacing of a business card thickness...guess what it seems to start easier now! Also on the side note..I'm not sure what size wire for the battery I supposed to use but I justr use some spare wire I have in the garage...I think maybe 12 gauge? Is that thick enough wire to connect to the battery and starter?

@NiTecIndustries

4 жыл бұрын

Mary H The ignition coil having that gap then meant the spark plug wasn’t getting the proper spark in the combustion chamber-causing the poor starting quality. Your electricals are working just fine. 14 gauge would be better wire. I don’t recall if it’s either 12 or 16 gauge that’s thicker, but 14 is common.

Do you have a schematic for the switch mechanism and the breaker? One of the wires from the breaker on mine came off and I am just looking for quick answer before I GO CRAZY. tHANKS FOR ANY INFO.

@NiTecIndustries

10 ай бұрын

Hey, see page 5, Figure 1 of the supplied PDF manual in the description.

Do you have a link for the torque wrench you used? Or a link to one that is similar or one that would work just as good?

@NiTecIndustries

2 жыл бұрын

Sadly no; it was passed down from my grandfather.

by chance is there a way to wire up a kill switch to the handle bars? like use the existing kill switch?

@NiTecIndustries

4 ай бұрын

If I’m assuming this is on a mini bike, you can try running the wire from the handlebar kill switch in series with the wire going to the coil and the key itself (ignition, not starting)

Like to have seen the starter key box on the front LH side forward.

@NiTecIndustries

3 жыл бұрын

See future Drift Trike videos on my channel; I actually moved it in the next part (Part 11)

Thank you, young sir for this video. I have a 5hp GC160 Honda engine(vertical cylinder - horizontal shaft). Do you know of an electric start conversion kit for this engine. I have made a few attempts to contact Honda, to no avail. I can't seem to find an electric start kit for my engine. Thank you ahead of time for the help.

@NiTecIndustries

3 жыл бұрын

Bruce Raykiewicz I don’t think that would be possible then. Again I must iterate that this is for a Honda GX200 212 clone.

What type of battery did you use? And what size wire for the battery leads?

@NiTecIndustries

3 жыл бұрын

For the kit it comes with a starter motor that "in theory" didn't need much to start it. I first used a 12V 5 aH 70 CCA battery and it would start on a full charge, but nothing more beyond that. I had to replace the starter motor after the cast aluminum chipped on the mounting holes. After doing that, the battery was weak and could not start. I would recommend using a battery that is *12V, 8aH, 120CCA*. Wouldn't want to get a battery that would blow the 10-Amp fuse on the switch box. As far as wiring goes I either have 14 or 16 gauge wire.

Anyway to do this on a 79cc predator? (Love the sticker on the pull start)

@NiTecIndustries

4 жыл бұрын

Unfortunately, I am unaware of any kits for the 79cc. It would be cool, but I don't think it is possible.

@localearrape1467

4 жыл бұрын

X!-NightHawk Videos-!X ok thanks

@miguel360kmc

4 жыл бұрын

Wish there was a way would think the same kit would work but idk if you happen to find a vid on this please post here thanks.. now for lights and horn you could use a phantom generator sold bye bike berry for motorized bikes this works on almost all 4 storke motors its made for the 80cc 4ts but have seen it on the 49cc and a 212 putting out 12.5volts at idle

I got Honda gx200 that never had starter and ordered the starter kit , do you have a wiring diagram how to wire it up ?

@NiTecIndustries

3 жыл бұрын

Start watching at 11:53, download the PDF supplied in the description, or google-search for it; It is not hard to find.

@djpitr

3 жыл бұрын

Thank you

What battery size did you use? I try to find out the smallest (least amps) I can get away with. Not much room for my application.

@NiTecIndustries

3 жыл бұрын

I can’t help you much but to see other replies to other comments.

@back2basics320

3 жыл бұрын

So you don’t know what battery you used?

@NiTecIndustries

3 жыл бұрын

@@back2basics320 No, I do, it's just I've answered it in other comments through this video but I will answer it again: I'm using a 9lb battery with 12V, 8 AH, with 120 cold crank amps. It's a slightly bigger battery, which might be a problem with your absence of room.

Thank you nice. Can i install electric start on Honda gx390 engin

@NiTecIndustries

3 жыл бұрын

If you can find a kit appropriate for it. Yes. This is not meant for it (GX190/GX200)

@bandaralahmadi1711

3 жыл бұрын

Thank you brother yes i find in Aliexpress.com

Where did you get the small battery? What's the model?

@NiTecIndustries

3 жыл бұрын

Please see other comments since I have answered this frequently asked question. Or check this video out at time stamp 1:50 kzread.info/dash/bejne/ZXmol9ClXbCrmKQ.html

How much wider does adding the starter make the motor? I can relocate the switches, but my engine is installed in a tight space.

@NiTecIndustries

Жыл бұрын

It doesn’t add much, at least a couple of inches if any.

@sonex761

Жыл бұрын

@@NiTecIndustries I have an inch past the seam on the fuel tank. Do you think it would fit?

@NiTecIndustries

Жыл бұрын

@@sonex761 Timestamp 9:30 gives you a visual. I don’t have the exact dimensions, but the radius of the starter passes the fuel tank.

So I don’t want to do a full on electric start but instead of the little red switch I want to put a key ignition would I need a kit or a 2 wire or like a 4 wire?

@NiTecIndustries

4 жыл бұрын

If I am understanding this correctly, you are still wanting to do a pull start, but have a key-switch at the front of your project? If that is the case, you only need a two-wire setup. I have done this with a key toggle switch in the episode where I install the drum brake. At the beginning of the video, I showed off how I did it. The hot replaces the lead wire coming from the factory switch, and the ground from the switch is grounded to the frame. Hope this helps.

@localearrape1467

4 жыл бұрын

X!-NightHawk Videos-!X thx man

@localearrape1467

4 жыл бұрын

X!-NightHawk Videos-!X but if someone wanted to start it but the wasn’t in it it wouldn’t start correct?

@NiTecIndustries

4 жыл бұрын

If the key is in the off position, yes.

@localearrape1467

4 жыл бұрын

X!-NightHawk Videos-!X could I take out the original switch and put a key ignition in instead?

Hey what battery did you use in this?

@NiTecIndustries

3 жыл бұрын

Please see other comments since I have answered this frequently asked question. Or check this video out at time stamp 1:50 kzread.info/dash/bejne/ZXmol9ClXbCrmKQ.html

Picked up a go cart for my son and i ordered the coils and flywheel to try and wire se lights for it think i can just hook the wire up to a battery or do i need a voltage regulator?

@NiTecIndustries

3 жыл бұрын

The wire coming from the charging coils does not need to connect to the battery; it is its own power source. The switch box from this kit provides a voltage regulator via the one way diode. Perhaps when you ground the light down to the frame, and the battery grounds to the frame, then it will charge? But you don't need a regulator I dont think.

@edgarsanabia6874

3 жыл бұрын

@@NiTecIndustries hmm i see i was going to attach the wire coming from the charging coils to the positive of the battery and just ground the negative to engine and have positive wires from the lights to the positive of the battery and negatives to chassis . Sounds like i might be able to just run the single coils wire to my lights then the lights ground to chassis? Thanks for your reply btw cool bike setup you should in the end

@NiTecIndustries

3 жыл бұрын

@@edgarsanabia6874 Correct; that's how I've seen it on minibike videos online. Just make sure the lights are grounded somewhere--maybe double check the voltage coming from the coil if you can.

@byronmill

2 жыл бұрын

@@NiTecIndustries this is only intended as a technical correction, but the diode does not provide any voltage regulation, it is strictly a half-wave rectifier (converts AC to DC). All small engine charging coils put out AC by design and the output requires rectification.

@NiTecIndustries

2 жыл бұрын

@@byronmill good to know man. Thanks!

How do you know if you have the hemi version or not besides pulling the cylinder head off?

@NiTecIndustries

3 жыл бұрын

AUSTIN ROBERTS No need to pull the cylinder head off. Check the valve cover. If it’s a shiny zinc, non-hemi. If it’s a cast iron, and it’s square with beveled edges, it’s a hemi. I also believe that hemi’s have tapered shaft, and therefore won’t be compatible with the flywheel provided in the kit.

@austinroberts5255

3 жыл бұрын

X!-NightHawk Videos-!X thank you!

Hey man is that a standard electric start conversion kit

@NiTecIndustries

2 жыл бұрын

Refer to the pinned FAQ, it is a Honda GX 200 electric start kit.

Will this charge the battery as well or would I need some sort of alternator?

@Ghost88890REAL

2 жыл бұрын

A battery charger is more cheaper.. but it should hold up for a few days depending on how much lights or battery use.

@NiTecIndustries

2 жыл бұрын

I could've sworn I responded to this, but if you have the kit, the charging coil will charge the battery. Please refer to the FAQ next time.

Hello. I hope all is well with you. What link is for the 212 predator?

@NiTecIndustries

2 жыл бұрын

If you mean where to get this kit, I left some links in the description and in the pinned comment for it. They’re the same thing but just different sellers. Otherwise I’m not sure what you’re asking.

I like the It’ll be fine

@NiTecIndustries

3 жыл бұрын

I’m A Bot at Life cause no matter what happens It WILL be fine. 😉

@andrewgibson9520

3 жыл бұрын

Can’t steal that that’s from cars and cameras 🤣😂

Hey can I put this same setup to my 50cc mini dirt bike is it possible 🤔

@NiTecIndustries

2 жыл бұрын

Please read the pinned FAQ; this is intended for the honda 212 clone predator 212. Unless if you're trying to utilize some of the components to make it work it is highly unlikely for your situation. So it's better safe to say no...

Can you still use the pull start if the electric start were to fail

@NiTecIndustries

Жыл бұрын

Correct

@elidogan5531

Жыл бұрын

@@NiTecIndustries thank you for the helpful video and quick reply it was very helpful

Vpowerequipment.com has a kit for the Hemi style Now.

@NiTecIndustries

3 жыл бұрын

And that kit i believe is this one for item #60363. Perhaps edit your comment to confirm? www.vpowerequipment.com/predator-212cc-electric-start-kit-60363/

Where did you buy the starter motor and the flywheel kit

@NiTecIndustries

3 жыл бұрын

Look in the description. Google search predator 212 electric start kit or Honda GX 190 GX 200 starter kit. Buy off of eBay or sellers that will sell it for under 100 bucks.

@blaydetroiani8563

2 жыл бұрын

@@NiTecIndustries does the kit come with the new fly wheel or did you buy it separately

@NiTecIndustries

2 жыл бұрын

@@blaydetroiani8563 I supplied kits in the description. But you can do either or.

is your gov. removed? what rpm can this setup handle?

@NiTecIndustries

Жыл бұрын

Governor still installed. It’s a cast flywheel setup similar to the Honda GX200, and if I recall they’re rated around 3-3,500 rpm?

How fast does your drifter go for that size motor

@NiTecIndustries

2 жыл бұрын

Current top speed is about 30 mph. 12T clutch and a 48T sprocket on 11" tires.

If I have a stage 2 kit on my predator will this still work?

@NiTecIndustries

Ай бұрын

Not without machining the billet flywheel to accept the ring gear; the cast flywheel with pre-installed ring gear won’t be able to withstand high-rpm.

There must be a way to install this onto a 79 cc predator engine. Do you know of a way.?

@NiTecIndustries

3 жыл бұрын

Sorry, but no. This kit is incompatible, and also there is not one in existence for the 79cc

Can you install an electric start on a Honda gx160 engine

@NiTecIndustries

3 жыл бұрын

Correct. This is technically the kit for the GX160/GX200

So is a battery necessary for this build?

@NiTecIndustries

3 жыл бұрын

If you don’t want the electric start, no; the battery is used to power the starter motor when you turn the key.

what ah/amp battery did you use?

@NiTecIndustries

Жыл бұрын

Please refer to the FAQ, but this time around, I'm running about an 11ah battery with no sweat.

witch kit did you use?

@NiTecIndustries

9 ай бұрын

Please refer to the FAQ and supplied links in the description, or google search one for a Honda GX200

The 12 volt battery at how many amps should it be?

@NiTecIndustries

3 жыл бұрын

No more than 10 amp hours; I would recommend 8.

@luismatiasgonzalezjuarez2369

3 жыл бұрын

@@NiTecIndustries thanks broo!

Does the starter protrude past the block on the clutch side? I have a cvt setup and need to know if it will clear. Thanks

@NiTecIndustries

4 жыл бұрын

Great question! Despite that I am not running with a Torque-A-Verter, but I went outside just now to check. It looks like the starter's face facing the shaft is coincident with the clutch side of the engine block. It looks like it does protrude past just by a cm or two, so it is possible you will have to do some trimming on your CVT plate.

@kevinolson5112

4 жыл бұрын

I put a starter motor on my 212 and I have a Torque-A-Verter and it works fine,plenty of space.

@NiTecIndustries

4 жыл бұрын

I would assume too that it depends on which torque-a-verter you have depending on how built your engine is. Since only said CVTs are rated for X amounts of horsepower. Also assuming too the orientation of the assembly depending if your engine is behind or in front of the axle.

@kxcody22

4 жыл бұрын

We’re you able to put back the pull start after the new electric starter setup

@NiTecIndustries

4 жыл бұрын

Olsen’s ATV customs Yes after having to modify the plastic piece behind the pull start cup.

Where did you buy that motor?

@NiTecIndustries

3 жыл бұрын

The motor specifically for this was bought from Harbor Frieght (Originally it was a Christmas present a few years ago). You can also buy it online from Gopowersports, BMIKarts and parts, and more. When the discount is advertising, it's on sale for 100$; retail price is 110$.

What battery did you use

@NiTecIndustries

3 жыл бұрын

Please see other comments since I have answered this frequently asked question. Or check this video out at time stamp 1:50 kzread.info/dash/bejne/ZXmol9ClXbCrmKQ.html

will the kit work with a predator 301

@NiTecIndustries

4 жыл бұрын

A proof of concept was demonstrated by the user "peter torregrossa" of doing so. You will probably need a different kit, as this engine is comparable to the Honda GX270. Try finding an electric start kit for that, then come back here. Link to peter's video: kzread.info/dash/bejne/pqqc3JWbn73JmaQ.html

Will this work on the hemi engine

@NiTecIndustries

2 жыл бұрын

Please refer to the pinned FAQ next time. The taper on the hemi versus non hemi is different, and this specific kit will not work unless you find a compatible fly wheel.

Does this work on the ghost 212??

@NiTecIndustries

Жыл бұрын

Refer to the FAQ; Not this kit specifically. Since the ghost is a newer engine and this kit was designed around the era before the Tilitsons came out. My best advice would be to find either a manufactured billet flywheel with a ring gear pre-attached that can take the load of the ghost, or take that flywheel on the ghost to see if they can take a ring gear and press fit it on the flywheel.

yoooo! Can i do this to my 2001 yamaha yz125cc shifter kart!!????

@NiTecIndustries

3 жыл бұрын

Music Account Sorry, but no.

@NiTecIndustries

3 жыл бұрын

Let me reiterate that this is for a Non-hemi Predator 212cc and other 212 honda clones. There may be a kit out there for your engine, and it may have a completely different procedure compared to this video. The kit used in this video is irrelevant and incompatible with your engine.

Is that flywheel safe for high rpm’s??

@NiTecIndustries

9 күн бұрын

Nope. It’s a factory cast iron not meant to withhold anything higher than the governed 3500. You’ll need one custom machined..

How do I put a electric start on a 301cc predator hemi

@NiTecIndustries

2 жыл бұрын

A different video attempted this, but this video would most likely be a similar principle

Will this work on a Hemi engine

@NiTecIndustries

3 жыл бұрын

Because of the tapered shaft on the hemi, this specific kit will not work, and which is why this instructable is for a NON-hemi predator HOWEVER, there is alternative parts (such as the flywheel) that you can order online to make the kit work in this case. I believe the flywheel brand is kohler. Check the comments and the community around this video to find further details. Sorry for the inconvenience.

Can I put a key start on a 196cc

@NiTecIndustries

3 жыл бұрын

Depends on the engine company. This seems vague, and the kit is for a Honda GX 190 and a GX 200.

Has anyone tried this on a Hemi and does it work?

@NiTecIndustries

4 жыл бұрын

There is a video lurking around here and there of it working, but this guy posted a video about that: kzread.info/dash/bejne/h3uq1NV_d5nMqto.html

hi will this work on my 168f diesel

@NiTecIndustries

2 жыл бұрын

Refer to the pinned FAQ; I also have no knowledge regarding those engines, so I wouldn’t ask here.

@tuckerbuzzell1882

2 жыл бұрын

@@NiTecIndustries ah ok

Can you put double coils if wanted

@NiTecIndustries

4 жыл бұрын

In a short answer. Yes, in theory. My kit did not come with two, but the predator does have a bolt circle that allows for two coils to be mounted. You only need one to plug into the wiring of the switch box, so the second could be used to power a front headlamp for instance.

Did anyone notice the it’ll be fine and cars and cameras sticker

What happens if mine doesn't have spark

@NiTecIndustries

3 жыл бұрын

Check your spark plug gap, ignition coil (additionally for wire damage, misconnections, etc.), and your spark plug; one of those is at fault. Additionally check the key switch wiring too.

@hayimhere9604

3 жыл бұрын

@@NiTecIndustries if I screwed up the metal at the edge of coil could that be a problem

@NiTecIndustries

3 жыл бұрын

@@hayimhere9604 Possibly, I don’t think so. I am not sure. And in general analogy, grinding on that metal can expose possibly better contact from metal to coil, but at the same time damaging it could have its disadvantages. I cannot help you here. It might be best to replace your coil to be safe.

How much did this cost you

@NiTecIndustries

3 жыл бұрын

Sorry for the late reply. It varies depending on the seller online. I think it’s under 100$ at least, but I can’t remember.

Link for the starter?

@NiTecIndustries

2 жыл бұрын

Comes in the kit, but you can search eBay for a GX200 starter motor.

@logankern2393

2 жыл бұрын

@@NiTecIndustries thanks man 🙂👍

This thing isn't billet though so it will detonate at high rpm

@NiTecIndustries

Жыл бұрын

Under the assumption that it’s a same casting as a conventional flywheel, yes.

@rayzor285

Жыл бұрын

@@NiTecIndustries I'd bet my last dollar that it's the same Chineseium casting as the stock one.

Currently unavailable.

@NiTecIndustries

4 жыл бұрын

Give me a second; I'll update the description with better links.

@NiTecIndustries

4 жыл бұрын

Ok. I updated the description. Sorry about that; that was the kit I put on my Christmas list back then, but it's the electric start kit for the Honda GX 190/200. Hope this helps.

@briscollama2521

3 жыл бұрын

@@NiTecIndustries Your video got me headed in the right direction. I found and ordered a Honda starter kit for my Predator 212 non-hemi head. It sounds like it can be used with very little modification. Thanks much.

@NiTecIndustries

3 жыл бұрын

@@briscollama2521 Glad to be of service my dude.

My kit starts BUT WONT KILL ENGINE PLEASE HELP 😂

@NiTecIndustries

Жыл бұрын

Check your grounds and the wiring that went from the spark plug to the original killswitch.

Does this work on the ghost 212?

@NiTecIndustries

Жыл бұрын

Refer to the FAQ, and I have answered this before: Not this kit specifically. Since the ghost is a newer engine and this kit was designed around the era before the Tilitsons came out. My best advice would be to find either a manufactured billet flywheel with a ring gear pre-attached that can take the load of the ghost, or take that flywheel on the ghost to see if they can take a ring gear and press fit it on the flywheel.

@everythingtech09

Жыл бұрын

@@NiTecIndustries ok so what do you recommend me getting for it?

@NiTecIndustries

Жыл бұрын

@@everythingtech09 With all due respect, I don’t have an answer for that. Last time I did some researching , an off brand go power sports company has a billet flywheel with a ring gear, but it is incompatible with the 212 series due to a tapered shaft. Like I said, your best bet is to take your ghost’s flywheel and get it custom machined for a ring gear that is compatible.

@everythingtech09

Жыл бұрын

@@NiTecIndustries ok thanks for helping