Scott installs a spalted sycamore mantel on a brick fireplace with steel rods.
Жүктеу.....
Пікірлер: 16
@PublicJunkiesHunting7 ай бұрын
Great video. I’ve been watching multiple videos and everything else I see is a more permanent installation. Going through the mortar doesn’t destroy the brick. Not using concrete anchors allows you to fill an empty hole in the future. Thanks for sharing
@thirstypilgrim97
23 күн бұрын
I would say he should have put some epoxy in the holes and on the bar to get all play out and secure them
@MrACOUSTICPETE Жыл бұрын
Thanks ! I appreciate the " common sense " not ' over technical ' approach . ☺
@EyeAmCoa5 ай бұрын
Very helpful
@taylorinspace7 ай бұрын
SO helpful thank you
@brilliant33410 ай бұрын
Thank you for sharing.
@Sophos19645 ай бұрын
Is the fireplace solid brick all the through to the chase’s exterior or a single course brick veneer? If it’s a single course brick veneer, wouldn’t you need to mount those rods into a wall stud in order to support the weight of the mantle?
@ScottWunderWunderWoods
5 ай бұрын
If I know where the studs are, I will hit those. If not, just the single brick depth is enough to support the mantel.
@pepsimantom5 ай бұрын
How much will this hold? The wood mantel I plan to install is a bit heavier than that one. It seems you’ve done this a lot and might hang a good idea. Specially, I’m drilling into studs and the wood mantel weighs about 75lbs. Also, when going into studs do you typically drill through the 2x4 studs or stop short if going all the way through?
@ScottWunderWunderWoods
5 ай бұрын
This will definitely hold a few hundred pounds. I know I can fully hang off of one and do it regularly to test it out. I usually drill 3-1/2" to go through most of the stud. You can go all the way through, but have to be aware of what is behind.
@mweiler327 ай бұрын
How big of a hole did you drill in the mortar?
@ScottWunderWunderWoods
7 ай бұрын
I drill a 3/4" hole. It ends up a bit bigger with all the jumping around of the hammer drill.
@mweiler32
7 ай бұрын
@@ScottWunderWunderWoods Assuming that gets into the brick a little too, right?
@ScottWunderWunderWoods
7 ай бұрын
@@mweiler32 Yes, but not too much.
@HollyDoucette-zs9pt4 ай бұрын
Hi Scott, I was wondering where you got your steal rods?
@ScottWunderWunderWoods
3 ай бұрын
Home Depot or Lowe's. They are metal stakes for concrete forms.
Пікірлер: 16
Great video. I’ve been watching multiple videos and everything else I see is a more permanent installation. Going through the mortar doesn’t destroy the brick. Not using concrete anchors allows you to fill an empty hole in the future. Thanks for sharing
@thirstypilgrim97
23 күн бұрын
I would say he should have put some epoxy in the holes and on the bar to get all play out and secure them
Thanks ! I appreciate the " common sense " not ' over technical ' approach . ☺
Very helpful
SO helpful thank you
Thank you for sharing.
Is the fireplace solid brick all the through to the chase’s exterior or a single course brick veneer? If it’s a single course brick veneer, wouldn’t you need to mount those rods into a wall stud in order to support the weight of the mantle?
@ScottWunderWunderWoods
5 ай бұрын
If I know where the studs are, I will hit those. If not, just the single brick depth is enough to support the mantel.
How much will this hold? The wood mantel I plan to install is a bit heavier than that one. It seems you’ve done this a lot and might hang a good idea. Specially, I’m drilling into studs and the wood mantel weighs about 75lbs. Also, when going into studs do you typically drill through the 2x4 studs or stop short if going all the way through?
@ScottWunderWunderWoods
5 ай бұрын
This will definitely hold a few hundred pounds. I know I can fully hang off of one and do it regularly to test it out. I usually drill 3-1/2" to go through most of the stud. You can go all the way through, but have to be aware of what is behind.
How big of a hole did you drill in the mortar?
@ScottWunderWunderWoods
7 ай бұрын
I drill a 3/4" hole. It ends up a bit bigger with all the jumping around of the hammer drill.
@mweiler32
7 ай бұрын
@@ScottWunderWunderWoods Assuming that gets into the brick a little too, right?
@ScottWunderWunderWoods
7 ай бұрын
@@mweiler32 Yes, but not too much.
Hi Scott, I was wondering where you got your steal rods?
@ScottWunderWunderWoods
3 ай бұрын
Home Depot or Lowe's. They are metal stakes for concrete forms.