Installing a 18th Edition RCBO/SPD Consumer unit | Walk through Video
Тәжірибелік нұсқаулар және стиль
Video of us installing a RCBO Consumer with a SPD also install some new gas/water bonding and rewired some accessories within the garage
⚡️⚡️⚡️Connect with me on Social Media⚡️⚡️⚡️
/ letelectrical
/ let_electri...
letelectrical.co.uk/
#electricianinpoole #localelectrician
Let Electrical Services
Electrician in Poole, Electrician in Bournemouth
Пікірлер: 28
Good job brother, love those lewden boards.👍👍👍👍👍👍👍
Personally I'd have routed the tails into the bottom right of the board to keep them clear of the circuit wiring, but good job all the same!
Not advisable to have fridge/freezers in garages. In winter when temperature drops, many stop working as designed to work indoors only. I think there are only one or two makes that will work in garages.
Hi csn you confirm me how much it cost to change the old cunsomer unit very basic one with there or four like one you filmed in lndond eara thanks
Nice run through. Was the water supply a metal service ? The gas bond probably should have been before any branches.
Who pulled that main fuse out?
Does the equipotential bonding on the gas have to be before the tee on the gas outlet pipe? I know nothing about electrical requirements. Not sure how much of a difference it would make on this installation? As a gas engineer, just wondering how much of a difference it would make here? Nice tidy work on the consumer unit.
@letelectricalservices5143
Жыл бұрын
Morning, The regulation like the gas bonding to be installed within 600mm from memory as stated here "The main equipotential bonding conductor connection to any gas or other service should be made as near as practicable (preferably within 600mm) to the point of entry to the premises." Hope this helps
Ok chef
Can you explain to me why there are 3 red 2.5 wires in 2 of the 32 Amp Rings? Are 2 of them for a Ring and the 3rd a fused spur maybe??? Answers Below Please .
@letelectricalservices5143
Жыл бұрын
Correct, 3rd is a spur
@Baggiolyful
8 ай бұрын
When I did my 18th edition refresher course my teacher pointed out that you are allowed to spur off a ring Mcb with one double socket and there it was in the regs book I didn’t know. This was useful recently when I needed a double socket in a cupboard for a cctv rack but the board was full.
@keithjackett9895
7 ай бұрын
Yes you are correct, i was thinking of an optimal design where one wouldn't require an add-on spur. thankyou for your responce Sir.@@Baggiolyful
@kennyla4060
6 ай бұрын
Your aloud to fuse spur directly from the mcb
@keithjackett9895
6 ай бұрын
What about bridging a RCBO cos you can only get 2 x 2.5mm cable in each Live & Neutral terminals? Are Wago blocks aloud??
Is that bonding cable protected against UV?
@letelectricalservices5143
2 жыл бұрын
It's not the best solution but only solution we had due to tile flooring and bathroom above the kitchen. Alot of Bonding cables are run externally and gas meter are normally situated outside in local area with no near entry.
@Dontmindme__
2 жыл бұрын
Think you’re missing the point, should be in conduit or otherwise protected against UV
@AGRElectrics
Жыл бұрын
@@Dontmindme__ give me a reg number that states this? Granted best practice but I can't think of any that would support it 🤔
@James_scott86
Жыл бұрын
You think UV is going to degrade a thick insulation and a 10mm copper? Been in the industry 20 years and have never heard that.
@simonmartin3433
Жыл бұрын
@@smudge0161 What's earth bonding?