Just purchased a L2610 and BH77, haven't received it yet, so was trying to learn how to install. Appreciate the video, and explanation, thank you.

Thank you so much for explaining about those extra brackets and how they protect the tractor from stress, etc. __THANK YOU__

@lacelleacres854

3 жыл бұрын

You bet!

Great video, just bought the subframe yesterday, backhoe will come soon. I have a L3901 but looks identical to yours. It never came with instructions for installing the hydraulics but seeing yours I think I can figure it out. Thanks

What a fantastic summary! I too have a 2501 and am thinking of a backhoe. Not sure I can justify the cost as it is only for use around my 1.5 acre lot. Nonetheless, this video has convinced me that if I do pull the plug, installing it will be fairly simple.

Thank you for answreing all my questions I would have. Great video

I have the same backhoe on my l3301 very handy little unit just put the thumb on you are correct comes in very handy

I finally got My Hydraulic lines on and they are tucked away and NOT LEAKING anymore. The fittings that came with the Woods BH-75 had 45 degree fittings and the fittings and Hose stuck way out What a pain Spent $42 at a Hydraulic Supply store for about 7 fittings to get 90 degree fitting at the hydraulic block and adapters to connect to the hose supplied with the Backhoe, and they still were sticking downward too much. ( Wound Up not using 5 of those fittings I bought ) I did not throw that original hose away I reconnected it at the Block and routed it toward the backhoe and coupled it straight to the supplied hose Yes it is too long, but now My line leaves the block with original hose closer too the tractor The extra hose length was long enough for Me to make an upward loop then down too the mounting bracket location for the female Quick Connector Excess loop easily tie wrapped to the unused slot behind the 3 Point lever slot and finally NO MORE LEAKS My Woods BH-75 came mount too a metal frame that I am hoping to turn into a roll around platform Not so sure rolling this thing around a lot is a good idea because it is REALLY HEAVY It took Me a while to move it without wheels. I tried using My forks and they helped but it was really unstable and top heavy My Woods sub frame has the bottom frame locations pointing downward, not like Yours where You raise the backhoe up & then drop it into the sub frame cradle Maybe I'll finally get thing working soon I've had it 2 years already Thanks and Sorry for running on and on, but it has been aggravating Ken in Florida

Hi I really appreciated Your Video I bought My L-2501 2 years ago and then bought the backhoe the following week I still haven't installed it yet, but I did put on the subframe and the Hydraulic lines I wish I had figured out the Power coating issue first, but I DIDN'T I haven't needed it yet but I want to get it on and ready and Your video was Really Great Thanks Ken in Florida

Mate found this video very helpful cheers

The lower arms can stay on. Pull the side links and turnbuckles off, the upper link, the lowers can be bungee corded to the ROPS and out of the way. Way quicker and easier, I have a L2501 and a BH77.

I bought the L3301 last year and am thinking of putting the BH77 on it. You know, the loader can't do everything. The local dealer quoted $10,250 for the subframe, backhoe, seat, and hydraulics intstalled with warranty. Basically everything ready to dig.

@lacelleacres854

3 жыл бұрын

I've had my BH77 for 10 months now I still love it and have many uses for it.

@donaldstrishock3923

7 ай бұрын

A Friend of mine said; "when you have only One Tractor without Backhoe, You Only have HALF Of a TRACTOR."

Build yourself a backhoe dolly, it will make taking the backhoe off and on a lot easier. I made mine out of 2x6's and 4x6's. DIYMyWay has a nice video on how he built his. His is a lot like mine.

Going Monday to get mine. This video will help! Thanks

@lacelleacres854

4 жыл бұрын

Congrats!

@michaelmactavish1728

3 жыл бұрын

@@lacelleacres854 love kubota fluids i use 100% kubota engine oil because kubota fluids are accully cheaper

Very good video. Thank you for this. BTW in the video when your tractor is running do I hear a knocking sound along with the engine running? Sounds like a little man in the transmission pecking his way out with a ball peen hammer.

I really wanted to watch this whole video but I got motion sick from all the rapid camera movements and light adjustments. I apologize. If you make another video I'd like to see it

Great video. Thanks.

@lacelleacres854

3 жыл бұрын

Glad you liked it!

Thanks for the explanation. I'm about to buy a b2601 with a backhoe. I will be switching between box blade and backhoe often. Needed to see how it was done. I always heard it was a PITA, but after watching doesn't seem to bad.

@lacelleacres854

3 жыл бұрын

Glad I could help. I have the process down to about 20 minutes if I take my time.

@hippiealloway9473

3 жыл бұрын

!

i put blocks of wod under mine for the sag.i have a woods bh80x.it s baisicaly the ame hoebut s alittle ifferent mount.i would hat to be without mine.

Thanks for the video! Looking to build a subframe for my hardy 6st backoe that will be install on my ex3200.

Nice I was looking for this on this exact tractor.

Can you still use the 3 point hitch with the subframe on?

The rear end is NOT aluminum

@lacelleacres854

2 жыл бұрын

Is to. Magnet doesn't stick.

@donaldstrishock3923

7 ай бұрын

@@lacelleacres854 maybe you got a weak magnet, or a "Chinese-ium Prototype ". Just try a Stonger magnet. 99% of These L2501-3901's are cast iron, nodular iron, cast steel.

I don't believe there's any aluminum in that rear end should be all cast iron. Reason why they recommend subframe mounted backhoes is because the 3-point back holes will tear the crap out of your tractor

@jmwarden1

2 жыл бұрын

On the B2650 it is all die cast aluminum

@lacelleacres854

2 жыл бұрын

It's aluminum. Magnet won't stick. I shared info that I got from the dealer.

What size taps did you use to chase the threads for the sub frame and small brackets? I'm having trouble finding the proper size.

@lacelleacres854

3 жыл бұрын

I don't remember off hand but I matched tap to the bolts supplied with the kit. I think it was 14mm x 1.5? Sorry for the late reply, been really busy around here.

at 11m38s, the stabilizer pads are down, and they stay down until you can raise them using the hydraulics. The earliest that can happen is 14m24s. Then you talk about the exhaust hanger pliers until the cut at 14m51s, after which the pads are up and you put the mounting pins back in. What happened in between? How on earth did you get the backhoe engaged with the bracket???

@lacelleacres854

2 жыл бұрын

Video editing happened.

So my question is how do you keep the chisel so cold ? Is it ok if you have a room temperature one ? How cold do you like them?

I see a lot of guys take the tires off to put the subframe on I never had to do that

@lacelleacres854

2 жыл бұрын

I didn't have to do it either but it made my life easier, not yours.

did you need to take the rear wheels off or can the sub frame be mounted with the wheels on.

@lacelleacres854

3 жыл бұрын

I think you should take the wheels off, otherwise it's a tight working space. I did one side at a time.

You're going to take the other hose off and throw it in the garbage LOL okay why would you do that? I took my spare hoses from my third function and backhoe hung on the wall in the shop for future use

@lacelleacres854

2 жыл бұрын

No need for me to keep the hose. Maybe for you there is a need.

Be careful with those zip-ties. They can turn into a chainsaw when under vibration.

Looks like you forgot to release the pressure in your valve control before trying to hook up your hoses don't forget to let people know that

@lacelleacres854

2 жыл бұрын

I did release it. What are you talking about?

what was the cost?

@lacelleacres854

3 жыл бұрын

a bit over 8k for everything. Labor was free :)

Should do yourself a favor get the Pat's quick hitch setup get rid of that big boat anchor you have

@lacelleacres854

2 жыл бұрын

I will look into it. For now it's about what I can afford.

What is the part number for the subframe kit?

@lacelleacres854

3 жыл бұрын

I don't remember.

@erikvaldur3334

3 жыл бұрын

If you go to kubotausa.com you can look up your machine. Look in the parts look up page. Then it'll probably be in the local options section. It may also be under the BH77 backhoe option section. I don't recall which area it's in. That is basically the same look up source the kubota parts guys use at the dealership. Subframe kits were sometimes a pain to find.

@jmwarden1

2 жыл бұрын

It is BH4673 for the B2650 with cab

If we're going to make videos should make sure you know everything there is to know about doing stuff like this before sharing with other people sorry

@lacelleacres854

2 жыл бұрын

I don't think so. I can make any video I want. I just did this to help. You didn't find it helpful. Move along.