Installation FX Impact Power Plenum kit (How To) (2020)
Спорт
The FX Impact Power Plenum kit will enlarge the capacity of the FX Impact plenum, which in turn will provide more power. This enables you to use heavy pellets or slugs and have enough power for them to reach their optimum speed, thus increasing accuracy.
In this video made by the Krale team of specialists, we’ll show you how to install the FX Impact Power Plenum kit in a step by step tutorial. We also tell you which tools and lubricants you’ll need, most of which are available at Krale.shop. You’ll find a list below of what you need to install the FX Impact Power Plenum kit, including links to our web shop.
FX Impact Power Plenum Kit: www.krale.shop/en/power-plenu...
Tools:
• Allen key 1.5 / 2 / 2.5 / 3 / 4 mm (www.krale.shop/en/screwdriver...)
• Pair of pliers
• Socket or spanner 11 and 22
• Calliper (www.krale.shop/en/caliper-fra...)
• Gas torch
Cleaners and lubricants:
• Interflon HW Lube spray (www.krale.shop/en/oil-interfl...)
• Abbey silicone grease (www.krale.shop/en/grease-abbe...)
• BoreTech Blast degreaser (www.krale.shop/en/degreaser-b...)
• Loctite or 2-component glue
Recommended:
• Soft vice inserts (www.krale.shop/en/vice-clamps...)
• Set of drifts/punches
(Including Dutch and English subtitles)
Please note: as we're not constantly monitoring the comments on our video's, we recommend sending an e-mail to info@krale.shop if any questions arise.
Website: www.krale.shop/
Facebook: / kraleschietsportnl
Instagram: / kraleschietsport
Пікірлер: 68
Definitely my favorite series of 'How to Install' videos for the Impact, thanks so much and please keep them coming !!!
Hey buddy.. Good video... 2 things you should say. 1. If the impact is without pressure, it makes sense to set the REC to minimum. With the PP you need less REG pressure. 2. If you secure Hammer Stop with glue or loctite, you should wait until the glue is ready. if you mount the valve spring too early, it is possible that the hammer stop will turn and the dimensions will no longer be correct ... Greetings Rick
Thats very professional demo..no missy screws lying on top of the table..full detail instruction one by one..viva Deutsman..
The most clear and easy procedure to disassemble and assemble the new PP. the English language text is great 👍. Thanks
Excellent video, just fitted my kit following your instructions and it works a treat. Thank you very much
Excellent Teacher and very highly skilled - Thanks for sharing your Knowledge with us.
Duidelijk en fijn dat er een goed filmpje op internet staat ! Heb het plenum vorige week succesvol zonder geïnstalleerd, en het viel erg mee ! Heb misschien één puntje, voor het dichtdraaien van het plenum heb de klepstang iets terug uit het klephuis getrokken, zodat deze niet heen en weer word gebogen.
Super uitgelegd, hartelijke dank.
What a very good clear example of a great video. I need to watch couple more times before I fit mine. And could not understand your language (sorry) but sub titles were very clear. Thank you.
Excellent step by step guide
Excellent! Thanks!
Excellent demonstration
Nice job! Thank you so much for your video sir.
Baie goeie en mooi stap vir stap video !! Dankie !!
Excellent video!
Perfect! Thank you!!!
Goede video, complimenten!
Mooi om eens deze kant van Krale te zien. Ik ben een paar maanden geleden voor het eerst op jullie nieuwe adres geweest en moet zeggen, een geweldige winkel. Niet voor niets dat ik als lucht sportschutter, maar ook als voorzitter van onze SV iedereen doorverwijs naar Krale. Goed materiaal, volop keuze, eerlijke prijzen en eerlijk advies. Kan alleen maar zeggen, ga zo door. De groeten van SV Woensel 77.
@KraleShooting
4 жыл бұрын
Bedankt voor uw positieve feedback!
@axelbouillon7859
3 жыл бұрын
Weet iemand hoe je aan de 6 tot 6,5 mm komt zoals beschreven in de video? Na installeren en het volledig indraaien van het oude stukje meet ik 8mm. Dus hoe dit aanpassen als dat stukje er al volledig ingevezen is?
How are you friends, recently I received my rifle mkII power plenum .25 to how many bars should I adjust the regulator to optimize autonomy and precision with 25 grains? thanks for help.
This guys a machine on the Impact, thanks for such an informed video. Now can you get some in stock so I can buy mine please. 👍
Dans di neiger is brace brace over dare , don’t forget to tighten di vuuuuuuuulve
HI, which green Loctite should I be using for this please?
Hello, I am looking for information before dismantling everything 😅 on my impact MK2 I noticed a small leak, I located it at the level between the Wheel and the adjuster? what part could this come from? Thanks in advance for the advice.
Buen vídeo se puede poner el plenun a una crown
Excelente manutenção é customização au mesmo tempo feis ais duas excelente trabalho like
Is there a break in period if the power plenum is newly changed?
Hi, do you sell the orings for the power plenum? I need the white pur oring
Hele goede instructieve video. En erg fijn dat de juiste maten worden gegeven. Maar toch enkele vragen. Wanneer de afstand van het uitstekend gedeelte van de hammerseat niet juist is, hammerseat in of uitdraaien tot de juiste lengte? (moet je vlot zijn met die loctite) Wanneer die afstand tussen de probe en achterkant van het huis niet juist is, aanpassen op het blokje voor? Lijkt mij bij beide vragen wel nml. Ik hoop de Power Plenum kit snel binnen te krijgen en kan hem nu zeker goed monteren, er zijn toch wel dingen die fout kunnen gaan zag ik.
Weet iemand hoe je aan de 6 tot 6,5 mm komt zoals beschreven in de video? Na installeren en het volledig indraaien van het oude stukje meet ik 8mm. Dus hoe dit aanpassen als dat stukje er al volledig ingevezen is?
Krale Schietsport Kun je de FX 2 Impact ook bestellen met .22 Slug Liner 700mm, zwaardere hamer, en Plenum fabieks af al geinstalleerd. Wanneer komt de MK3 uit.
That is not the first time you have done that, very professional. I did not see you put the black plastic hammer spring guide back in, off camera?. thank you
@KraleShooting
4 жыл бұрын
That's because it's not going in again. This part is not needed anymore. ;)
Mooie uitleg voor de installatie van Plenum, maar groene loctite of bedoel je blauwe loctite als later hammerseat nog los wilt krijgen. ;-)
Siêu phẩm 👍👍👍
Hi...the new power plenum kit should include the pur o ring and the normal one..because I didn't find it in my kit?
@rossmcneil2261
4 жыл бұрын
AHMED A I thought the same as you but I eventually found them already seated in position 👍
mantap👍👍👍
my mag wont fit when i mesure to 44.4 to 44.7
Rubber ball 6,35 NBR90 missing on valve adjustment spring 🤔
What happen to the buffer oring and plastic spring guide for the hammer?
@samsawyer2145
4 жыл бұрын
Buffer is now a delrin attached to the hammer and the old spring guide is replaced with a new one
Is there no more buffer oring ?(C3 bumber) Very nice and helpful Video thanks foe making this.
@humphreydavids
4 жыл бұрын
I would put in a new white delron C3 bumper. The old blue o-ring one wears out easily. I just replaced mine. Very cheap on Ebay.
@thangmohzonizuka
4 жыл бұрын
@@humphreydavids mine white delron C3 bumper just arived I will replace my MkII on this weekend . And I wait for my dealer to order a Power plenum for me.
@subsonicreviews1835
4 жыл бұрын
yea, i think he forgot to put the c3 bumber o-ring.
@CountDown2012
4 жыл бұрын
@@humphreydavids Please can you give me a link? I am just starting to learn.
@laihong4107
4 жыл бұрын
huw mauh
congratulations, excellent images and detailed step by step upgrade.
@KraleShooting
4 жыл бұрын
Thanks, we aim to please. 😉
@marcelogalvez9516
4 жыл бұрын
@@KraleShooting Three questions: do they have in stock? and there are versions - not original FX - that also consider the modifications to the pellet feeder and the barrel connection ... is there an improvement still pending by FX to improve the greater air flow generated by the plenum? Finally, this original internal plenum of FX is compatible at the same time using it with the external plenum ... as for a larger volume of air? or is it already unnecessary at this level? thank you very much for the help, greetings
@KraleShooting
4 жыл бұрын
@@marcelogalvez9516 1. This product is currently out of stock. 2. We are not aware of any upcoming updates. 3. It would be possible to install an external plenum but we would not advice to do so as there is not need to do that because the FX Power Plenum already delivers optimum power.
@marcelogalvez9516
4 жыл бұрын
@@KraleShooting thanks for answering. Much success to the store. Greetings from Chile
Hi, followed this but the alignment of the valve housing at one end and plenum end cap hole at the other is way out, meaning that the valve rod is not straight. Way out, like 130° out. I don't want to tighten the end cap more, and there is nothing to grip on anyway, and if I back it out by unscrewing to align the holes the rod goes through, the cap o-ring seal isn't made and air just rushes out. The alignment of the plenum end cap seems constrained by the cap and plenum thread, but that is allowing it to turn too far causing the misalignment. What am I doing wrong?
@KraleShooting
Жыл бұрын
Hello Miguel, our best advice is to call our customer serivce department and have them connect you with our workshop. They can help you with your problem, but the answer is unfortunately too long to answer via text in this manner. You can find the contact info on our website. Hope this helps you with your problem.
You should have put the power wheel to minimum before firing it to empty reg.
this rifle is impact X or impact mk2 ?
@atb2489
4 жыл бұрын
Impact X
Can somebody get this guy a wireless microphone. I cant watch this.
Ban oi cho minh sinh cay sung do nha cam on truoc nhe gui ve viet nam cho minh di
WEL GEDAAN
I believe, it is a very good air gun, and, a price ... ok, when you want a "ferrari", you don´t care about the price . . .
This is not the proper way to assemble it. The part that goes in to the trigger housing needs to be assembled first alone and tightened with the dimple right in between the clamp gap. Otherwise it will never align properly. Sure it will look ok but the barrel insertion and removal will be almost impossible and you will cause permanent damage to the entire parts of the rifle. Thre was an ernest rowe video on how to do it but I think FX has taken it down probably to make more money for the dealers. I tried this method and failed. The Ernest Rowe method worked like a charm the first time.
Roses are red, violets are blue, the title is in English, so the video should be too.
As easy as that 🤣🤣🤣🙄🤔😳