Gracias! Me salvó la vida

@cris_crow9827

8 күн бұрын

Saludos bro ! Gracias por ver 👍🏻

Grande crack sigue así que eres una gran ayuda para los que van tras de ti..

@cris_crow9827

4 ай бұрын

Muchas gracias por el apoyo hermano ! Saludos ! 👍🏻

Que crack! Tambien tengo un lancer al cual le quiero hacer algunas mejoras. Una de ellas es colocarle espejos abatible/retráctiles. Vi que tenes varios videos sobre el lancer.Te ganaste un seguidor!

@cris_crow9827

5 ай бұрын

Gracias hermano ! Y si , lo divertido de tener auto es modificarlo a tu gusto , anímate a hacerlo ! Un saludazo !

For my english peeps This video is a guide on how to install taillights on a Mitsubishi Lancer. Here are the detailed instructions in English: * First, remove the trunk carpet by unscrewing the screws holding it in place. [1:00] * Then, locate the taillights and carefully pry them loose with a plastic tool. [1:30] * Disconnect the electrical connectors from the taillights by turning the bulbs and pulling them out. [2:00] * There are three bulbs on each side: brake light, turn signal, and running light. [2:10] * Now, remove the two nuts holding the taillight assembly in place with a 10mm socket wrench. [2:30] * Repeat the same steps on the other side to remove the other taillight assembly. [3:00] * Locate the new taillights and identify the wires. Grey wire is for brake light, yellow for turn signal, and black for running light. [3:10] * Connect the corresponding wires to the sockets on the new taillights. There will be one leftover socket that you won't need to use. [3:20] * Insert the wires into the rubber hose and carefully cut the hose open along its side to avoid damaging the wires. [4:10] * Connect the black connector to the new taillight, and leave the other black connector free for now. [4:30] * Route the wires through the designated hole and secure them with electrical tape to prevent tension. [5:00] * Test the connection by turning on the lights. [5:30] * Install the new taillight assembly and screw it back into place. Repeat on the other side. [6:00] * Connect the leftover black connector to the black connector on the other taillight. [6:30] * Attach the resistor to the bottom part of the trunk with 3M tape. [7:00] * Connect the remaining sockets to the new taillights and tighten the nuts. [7:30] * Connect the leftover wires together and secure the connection with electrical tape. [8:00] * Reinstall the trunk carpet and secure it with the screws. [8:30] * The video ends here showing the before and after look of the taillights. [9:00] I hope this translation helps!

@cris_crow9827

8 күн бұрын

thank you!! 🙏🏼

Cuando se descomponga un led q pasa se puedes cambiar ??

@cris_crow9827

3 ай бұрын

Se puede soldar o remplazar el led

Yo se los coloque hace como 1 mes, pero de la nada las 2 que van en la puerta del maletero (las 2 de en medio) dejaron de encender, alguna idea de que podria ser?

@cris_crow9827

4 ай бұрын

Que tal, no se habrán desconectado ? Checa si le llega voltaje a los bulbos

@Caronte336

3 ай бұрын

Hola a lo mejor sé quemo la resistencia o le está llegando bajo voltaje

que modelo es?

@cris_crow9827

5 ай бұрын

El auto es Mitsubishi lancer ES 2008, los faros son VLAND LED , Brake Lamps LH & RH

@reznorkubirck247

5 ай бұрын

@@cris_crow9827 gracias