PLEASE this is awesome. Keep this up! I want to make every FNG in my shop watch this until they can repeat it word for word.

This video has really helped me out. Honestly I didn’t know about the 12 degree angle. Thank you .

Great stuff!

More please.

its very useful..thanks

The video is fast, but it is accurate!!

Nice Video 👍👍👍

I've never understood why you would want an indicator that needs to be set up at some oddball angle like 12 degrees.

Grandpa's advice voice

More like this

Nice

Pretty cool, but you missed one thing. A test indicator is really only intended to "test" the difference between two surfaces, its not intended for taking measurements. the reason being that it will inherently have cosine error, but when you are trying to get two surfaces to match up, that distortion to the measurement scale is irrelevant.

@haasautomation

3 жыл бұрын

David, Here are just a few instances where a numerical value is an important result of an indicator reading: Checking runout of an end mill mounted in a toolholder. Tramming in a vise on your mill table. Dialing in runout on a round part clamped on your rotary table. Checking an accurately turned or ground bore to ensure it meets a TIR specification. In all of these situations you are typically looking for an actual numerical value to assign to the measurement you’ve made. And many times this value means the part is either in spec or not. Let alone the measurements we make all day long here in the factory during machine alignment. Every one of these measurements has a numerical limit.

what if the workpiece was magnetically fixtured, would that effect how the test indicator works?

We use metric for language

just got my first DTI ... How do I set the tip? or move the tip?

hey im having issue could you guys tell me haas renshaw probe code for a partial boss probe cycle to find the center of a boss thats not fully round

@Eggsr2bcrushed

3 жыл бұрын

G65 P9823 is the renishaw inspection plus routine for 3 point vector bore and boss probing.

WOW

Hello can you help me for this question? A dial indicator is used to measure ___________. A. Positive readings only or B. Shaft eccentricity, thank you, cause im confused for my exam reviewer same questions but both A and B are the correct answer, i think there is some correction there. Thank you.

You didn't talk about the effect of gravity when using an indicator horizontally. Not everyone has a coax.

🤖🤖

how many barleycorns to an inch? i keep forgetting

@cvspvr

2 жыл бұрын

the number of ogre feet in a furlong is greater than or equal to the number of barleycorns in a baker's groin pouch

Love these videos but so many are in imperial, why can't the yanks use the same as the rest of the world haha

@mrnobody6322

Жыл бұрын

Mm

@Blobby_Hill

3 ай бұрын

25.4 mm = 1 inch. Do the math

I guess the metric system doesn't exist...

@Robinlarsson83

7 ай бұрын

I mean, Haas is an American company, mainly focused on the American market, where the absolute majority of their customers are using dead king units :p

I usually don't comment but there is misinformation about tip angle. First of all dial test indicator's tip must ideally be positioned parallel to surface you test, that where you get the most accurate measurement. Only Interapid and Mahr will give the same measurement up to 12 degrees. Try to do it with Mitutoyo and you will see what I mean. Interapid are great indicators but so overpriced, it's ridiculous. Not everyone can afford to buy them.

@haasautomation

3 жыл бұрын

Toucan, We specify in the video that the 12 degree alignment information applies to Interapid indicators. The reason we predominantly use Interapid indicators during machine alignment, and through much of the machine shop, is that the ability to position the stylus at 12 degrees off of parallel makes many measurements substantially easier where it would be difficult to hang the indicator off the edge of a surface to attain a parallel orientation.

@tucobreakinbad5000

3 жыл бұрын

@@haasautomation Exactly! kzread.info/dash/bejne/e6mXyJp9h5i-fdY.html

Boring, Mark from Tip of the day could explain much easier and fun.