A good, practical, helpful video here, THANK YOU. I've bought second hand stuff many times. Usually quite worth it if you are willing to put in the time and effort (and care) to do a proper job, but sometimes you come across an item that's been "attacked" by somebody who should never have been allowed to get anywhere near anything that has moving parts.

Good video. I have had mainly good luck with secondhand models. I would like to add a few more things. Carpet and or pet hair tangled up in the wheels. Loose crank pins I had a loco self destruct through this. I would ignore people just being negative rather than being helpful. Cheers Paul.

@DaveAtLittleton

15 күн бұрын

Great advice 👍

Good points well made👍💜✌️ I could tell a story or two about second hand purchases - most of my stuff is😲🤕🙄🤭🤭🙄🙄

I would suggest that if you’re going to glue lamps on brackets, then use a PVA type glue as it’s water soluble. It dries clear and can be easily removed without damaging the paint work. You can also use this method to secure weights in place too. Good instructional video by the way!

@DaveAtLittleton

27 күн бұрын

That is a great tip, I think when starting out you just assume Polycement is the way to go as it comes with Airfix kits and so there is a strong association there and so people, including myself, fall in to that trap.

All good advice, and even more so if you model in N gauge! Tiny quantities of oil particularly, and blot off the excess with a paper towel or cotton bud! Keep the wheels and pickups clean as well.

@DaveAtLittleton

28 күн бұрын

Thanks, Yes I have one N-Gauge loco (a LMS 4F that I picked up for £25), after a fiddly clean it is a speedy little thing!

That sounds silly putting lose weights inside the Loco!!! 🤔😉🚂🚂🚂

You are quite correct about purchasing second hand, it can be a blessing or a curse. However, I wouldn't have touched this one on seeing the damage done to the smokebox, handrail, broken vacuum pipe. In my experience, if it looks clean/as good as new it usually is just that, and that goes for the running characteristics as well. Again if the purchase was made with a makeover in mind then that is another consideration.

@DaveAtLittleton

28 күн бұрын

True, I have had some beautiful bargains through second hand. With this one, I didn't plan on having it weathered, I would have preferred pristine, however, I am not adverse to having it weathered, and so a slightly cosmetically tarnished loco with be the perfect candidate for me to dip my toe in the water in that area.

@crewelocoman5b161

28 күн бұрын

@@DaveAtLittleton Try weathering powders, Humbrol make them, very quick, very easy to apply and give a terrific look and finish. I'd spray the bodywork matt black or dark grey first. The powders do stick to the matt, but I'd recommend a matt varnish over the top to aid with handling.

@crewelocoman5b161

28 күн бұрын

P.S.: I forgot, not being funny, do look at archive colour photos first. Because it's "weathering" it's easy to think it can done without referencing the "real" thing first. Believe me, it won't look right if you don't get a feel for how it really looked!

@DaveAtLittleton

28 күн бұрын

@@crewelocoman5b161 Thanks, great tips, I will either do some thing like that or I will chicken out and bung £30 to TMC to do it for me

Perhaps the lesson here is to buy new, not second hand. If you buy second hand then golden rule is Caveat Emptor. Cheers.

@DaveAtLittleton

21 күн бұрын

A very sensible rule to keep in mind 👍

Ignore the keyboard warrior criticsm about your production values, I suspect they have never tried to run a You Tube channel or create content, you will of course improve with experience, what matters is the content, which was most helpful for new modellers or modellers who want to buy second hand, and improve their purchase. It was most helpful, and is why we watch these videos. I also watch OO Bill, Ians N Gauge, and Chadwick Model Railway, they all do good stuff some of which I would never attempt, but is still worth following to learn from them. Charlie is also running U Tube channel development workshops so it might be worth you investigating if you want to enhance your craft ? I have subscribed and look forward to your future content.

@DaveAtLittleton

24 күн бұрын

Thank you for the very kind words Mark. I'm not sure I will ever reach Charlie's standards but I am with practice my videos will get better. My videos are all very different at the moment as I am still trying different ways or making & editing videos and working out what works well for me and what people like so thank you very much for the feedback 😊

@martinsims1273

10 күн бұрын

​@@DaveAtLittletonkeep at it. :-)

Been following you for a while on Instagram, but just realised today you have a YT channel too!

@DaveAtLittleton

29 күн бұрын

Yeh, just me rambling, feel free to watch with the sound turned off! Nothing on my channel as good as you produce

@dibsyardshuntinglayout

29 күн бұрын

@@DaveAtLittleton don't be so hard on your self, Dave. Good advice you gave about that loco!

@briandugan4974

28 күн бұрын

That’s the worse 9F I have ever seen. 😊 Set of wheels missing for a start.

@DaveAtLittleton

28 күн бұрын

@@briandugan4974 haha, I best change the title!

What solvent, if any, do you use to clean off the old oil?

@DaveAtLittleton

7 сағат бұрын

I used rubbing alcohol as it normally doesn't react with the finish or decals on modern models unless you really scrub as I had to on this occasion. The loco is all fixed now, I used thinned satin acrylic gloss in a cheap air brush and it looks like new.

For future videos I'd suggest you avoid repetition - 3 minutes on not overdoing oil? And 3 hours to clean it with a huge pile of cotton buds? 1 minute with electrical contact cleaner and a couple of cotton buds is all it needs - see OO Bill videos. I'm afraid I stopped watching the rest of the video.

@DaveAtLittleton

26 күн бұрын

Noted, I try to avoided repletion but in videos that are meant to be educational in a sense, repetition is also necessary as it's how people generally learn so there is a balance I have to strike. Yes, I watch OOBill, he's very good, the oil or grease on the loco body was old and had dried and worked its way in to every tight space. I can take apart and clean a loco relatively quick and easily but this one was really bad and that's what led me to making the video.

@martinsims1273

10 күн бұрын

​@@DaveAtLittletonone of the problems is that many plastics are made from mineral oil, so if any mineral oil is left on the plastic bodywork, the oil and the plastic begin to amalgamate with each other.

Please use a tripod shakey video is so anoying.

@DaveAtLittleton

27 күн бұрын

@@davidbraun6568 Thanks for the feedback, I do have one but opted not to use it for this video so I could easily bring the camera in close on the damage, but I will try and use it more 👍

@martinsims1273

7 күн бұрын

​​@@DaveAtLittletoncan I suggest that you make up a semi-flexible arm to mount whatever you are using for a camera: Basically 3 lengths of 2 x 1. One of them you drill through near both ends (the middle piece), and the other 2 drill through (the same hole size) in one end only. Join the 3 pieces with a couple of bolts with plain washers and WING NUTS, to make an arm which can be positioned any way you want, and locked tight with the wing nuts. At one end fix your camera mount, and at the other end make a foot/ base (a couple of small blocks of wood and a board to do as a foot), which can be clamped in place, or weighted down. Simply position the arm to suit your preferred camera view. Hope this helps.

@DaveAtLittleton

6 күн бұрын

@@martinsims1273 I had not thought of that, thanks!

Anyone who has trouble sleeping doesn't need to take any sleeping pills just watch this video. I had fallen asleep after 2 minutes of watching it.

@DaveAtLittleton

27 күн бұрын

Haha, well glad I helped you achieve something :)

@ampersand.

25 күн бұрын

Such a gentle and soothing voice. Lovely :)