Use code LONESTARHAWAIIAN50 to get 50% OFF your first Factor box plus 20% off your next box at bit.ly/4bdQt0t!

@Jessersadler

Ай бұрын

whatever door you get, get a side pull, so it clears out the space above your door

@krisleaton4026

6 күн бұрын

What cloth are you cut from to throw a wooden stake through ply wood wth

Felt like an eternity since the last video, but glad to see the progress. Thoroughly enjoying this build series. Keep up the great work!

@johnharrel7514

2 ай бұрын

Poor family has been through it! The DR Horton episode was way too close to home… THEY SUCK! Glad to see our Chevy influencer kicking butt!

HOA "when the F**K is this eye sore going to be finished? " LoneStar Hawaiian “Doing his best bob Ross on plywood”

Need to go with the 14-ft door so RVs and the like can be parked in your shop. You never know what the future holds! The three overhead doors with high performance insulation to take a look at are the Raynor TM200C, Haas 2033-20, and the Clopay 3720. The Clopay was the cheapest for me when I got my 14'h x 16'w door.

Great job a sheathing the backside; right-side and part of the front of your new shop building! I cannot wait to see you finish sheathing the front of the shop building, and installing a garage door! Well done!

You should definitely do high lift tracks and also wall mounted garage door openers.

I know you're saving a ton of money doing it yourself but I also know it's still expensive. I watch all the ads for ya bro. It's what I hope folks do when my channel eventually gets monetized.

High Lift Tracks and Direct Drive Garage Door Opener.

I think I’ve been following you for around a year now and your channel has quickly became one of my favorites and I look forward to seeing your content

@jasonmiller3541

2 ай бұрын

Same here

@LonestarHawaiian

Ай бұрын

Much appreciated! 🤙🏽🤙🏽

Thankfully I no longer live in an HOA, so I can do whatever I want. That being said my shop walls are just the sheet metal (24 gauge) with fiberglass insulation batts behind them. I used to think this made me lucky - it was fast and easy to install. However, I have since learned that anytime I want to hang anything off the external walls outside or inside the shop, I have to build out a 2x4 wall in any case. I didn't really end up saving any time (or money). Oh well - learn as we go! Love the progress on your shop, thank you for sharing it with us!

@bch5513

Ай бұрын

Feel you on that one.. 😢

@vi0cs

Ай бұрын

fast and cheap doesn't always mean better.

Your Art skills are just as impressive as everything else on your channel. 👍🏼🇺🇸🧂

Man, I felt that last clip. After mine was done I just sat inside and stared at everything for about an hour. It's a great feeling being inside a blank slate. I will tell you this... Jack-Shaft door opener. It might be a bit more than a chain or belt drive, but the things are super quiet. additionally, it's one less thing that "pierces" into your shop. I've got one on my 12'x12' door. Also keep in mind when you're doing quotes that you may be asking for an odd size, which can cause the price to exponentially go up. Using standard dimensions will keep it slightly more reasonable. Loving the videos! Keep it up!

13’ door is high enough. They can run the door rails at an angle to follow the roof. Also go with a lift master garage door opener, they are very quiet and reliable. I just had 2 installed at the firehouse I volunteer at.

@TheSaw410

2 ай бұрын

I second this. I used to run a 1 million square foot shopping mall, never replaced a lift master brand opener but replaced a lot of other brands with lift masters!! Great quality units.

with the side mount garage motor you can suck those tracks up pretty close to the roof.

Regarding your door situation. Do what I call a double frame. Frame for the large door that you may want or help sell the place in the future. Frame in the smaller more affordable door, inside that frame. When it comes to the brick work. Brick it with expansion joints at the larger door. Maybe add some decorative touches within the large door frame so it blends in and looks like it was done on purpose. Down the road, easy tear out of the door to install the large RV style door. As for windows in the garage door, my opinion absolutely a must.

@LonestarHawaiian

Ай бұрын

Creative approach 🧐 I like it

High track system will get the tracks up against the ceiling and you can go whatever height door you want.

Here's a probable solution to your garage door opener. I bought and had installed a direct drive opener. It attaches to the pipe that turns to open and close the garage doors. Lowe's sells them and believe me when I say it's a lot easier to install. Now, thats on a regular two car garage door, but hey maybe they make one for a longer door. It's pricey, but worth the money. It also comes with an electronic lock so no one will be opening that door when you close it. It was around $500. Last year so it might be a bit more now. Good luck with the project!

Had to give this a thumbs up for showcasing the journey. Really appreciate the channel, you gave me a few upgrade ideas I was able to implement on my 2020 RST. Keep up the great work!!!

Hey, no worries on gaps. We know you’re busy. Thanks for free content and progress. Just forwarded to my own dad, to subscribe, and enjoy your world.

@LonestarHawaiian

Ай бұрын

🤙🏽🤙🏽

Always check in for the updates. I fully understand the struggle with work. I work about 75 hours a week and have so many projects I want to complete. Keep up the great content.

Put in a flat slat non insulated door and then insulate yourself. There are plenty of videos on how to do it and it’s cheaper and better insulated. Also, if your roof is high enough, run the garage door straight up, not up and over. That way you aren’t blocking ceilings and lights in the building when the door is open.

Awesome progress! I have been enjoying watching your shop project, thank you for sharing your journey

Looking sharp. Thanks for the post comparing the sheeting prices. Hadn't been in for awhile and didn't realize how much things had gone up. WOW !!!!

I have that style of door. It was just the thin metal so i added 3/4 foam board to the inside. huge difference in temp.

Great vids. My brothers and I build our own shops on our ranch here in Texas as well, and it's way more work than people realize. We went a bit bigger, and built 3 shops totaling 32,250 Sqft, encompassing a full paint and body shop, metal fab and cnc, wood shop, car workshop, powder coating, and 6000 sqft showroom for our car collection that is already too big, even with 5 four car storage lifts. We built almost everything ourselves except for the concrete, and after putting the roof on the 110x100 paint shop we said no and had the other shops roofs done. We also had spray foam done, and had 8 full glass garage doors installed, as well as 5 storefront window sections that are 21'x8', and 3 sections that are 16'x8'. All we have left is grinding and polishing our own concrete, pouring 40,000 sqft of concrete drives outside with all the storm water drainage, and finishing off the interiors completely so we don't see any insulation at all. Keep up the great work, and good luck with the rest of the project.

@powderdescent

Ай бұрын

How much was all that?

@LonestarHawaiian

Ай бұрын

💯💯

Could consider a aircraft hanger style insulated door. Also see them on farmers buildings. Can build frame yourself out of square tubing and insulate with foam board. You could build that 100 percent yourself

Some will just skip the sheating, tack on Metal Siding...then sprayfoam inside 1.5 INCh , then Insulation...Sheating is pricing itself out of the Market.

@blamuk

Ай бұрын

But you have a point. It's a waste of structural sheathing when all it's doing is..... ? The framing will hold up siding, the spray foam will make it airtight. So the sheathing is a waste.

@andreewert1925

Ай бұрын

@@blamuk People adapt..Many Farmers mill their Lumber, mostly Posts or studs..and they Do without Plywood that ends up rotting if exposed to Urine and Dung of Cattle, so they prefer either Planks or Metal Siding...or Half and Half , as you see in Horse Barns, with a Ply on the lower 4 feet section of a wall, metal above it, often uninsulated in Barns

@ragingrevenge1

Ай бұрын

@@blamukwind shear is a real thing. Metal siding has zero shear value.

Been seeing your channel since before you started building your dream garage and I gotta say every video you make just seeing the transformation of your garage from nothing but grass in the backyard to almost being done is amazing bro!! Keep it up you’re almost there! Can’t wait to see the final product!

I built a 24x30 metal building (not red iron though) and used sectional garage door. My opening is 18ft wide so it took a little longer to get the order, but it was a fraction of the cost of a roll up door rated for our wind requirements 120mph in the Mojave desert. My door is only 8ft tall, but my peak is 15ft with a 12ft ceiling height at the trusses. I had them use high lift tracks so the door snugs up to the ceiling very nicely. Unless you need the extra height for an RV then limit the size of the door because even the most expensive sectional doors don't insulate as well as the walls. I have 2in of closed cell spray foam on the walls of 24gauge PBR panel and 3/4 ACX plywood, but I can really feel the heat from the door compared to the walls when the sun is lower in the afternoon blasting my garage door. Nearly any local home garage door installer can get and install sectional doors that will work very well for much less than the cost of a commercial roll up door.

@LonestarHawaiian

Ай бұрын

Thanks!

Great idea to have the mural on the back of the shop

You have one the best eclipse time lapse of all the channels I follow great job on it and wonderful job on the shop❤

Being a big diy’er, you’re doing a great job and saving yourself a heap of money.

We are loving it! 😮

Have you considered a wall mounted garage door opener. Provides a clear Streamline look.

Looking great! I was on the same path with doors, and the same thought. I wanted flat panel, insulated and roll up, with a good weather seal. Like you, I also decided to do standard doors and deal with the track, because the cost was so ridiculous. I will echo the comment below about Clopay. Went through the Home Depot door design tool with them. It was a great price, and it was a quick and easy process.

The shop is looking great. Awesome job

It’s looking awesome! Don’t skimp on the door. Wait for have to. Insulated without tracks would be the way I would go. As someone I know says buy it nice or buy it twice.

Algorithmic engagement comment - Love the work. Love the overcoming the struggle. Love the persistent positive attitude.

You should talk to the house garage door sub to see if he can add on 1-2 extra door sections. 8’0” too short for your front fascade. 10’ or 12’ would look mo bettah. You might have to use a 3/4hp motor for add’t weight….. You should also check how much more to hang door higher. With an 8’ door head height, hang door 10 or 12’. Will provide way more headroom for normal activities, and more latitude on car lifts in the future. IMHO. Good luck. From a bruddah in Nuuanu.

Looking fantastic bud, love the mural on the back wall. I'm hoping to get my ceiling installed on Friday, I've been running water and air lines throughout the whole shop and luckily I don't have any leaks! Take care and don't work too hard out there!

bendpak need to sponsor that guy. like realy. if anyone got contact, now is the time. nice work buddy !!

Molokai building is looking nice, with all that sheeting to put in that makes a big difference, when wind blows from the West you will need to have that garage close at all times. Great job....

Enjoying the progress. Keep it up.

Amazing work with the building keep up the good work ❤❤❤

You can do the new roll up insulated garage doors so there’s no need to worry about tracks

I’m so excited to see this thing finished

The amount of pride and thought you put into what you do is top notch. 👌🏽

Looking good man can’t wait for the finish project

Man you are doing great. Its got to feel so good to look out back and see this massive garage and know you built that yourself minus the steel work.

Encouraging to see the zip hold up so well. We are just about finished with our custom home here in Tx and I paid up to do 7/16 zip for walls and 5/8 zip for roof decking. A lot of builders on YT seem to recommend zip which is what sold me on it.

Insane amount of work you've put in

Been a pleasure watching! Your marketing career is clearly audible in the pitch explanations; ❤️ it! From a fellow CMO, can’t wait to see more progress!

Love the progress brother! 👌

You should get a high lift garage door

you get shit done buddy!! it's coming together nicely!! 👍👍

Love the progress. Been watching since the beginning.

Dude i love that your channel keeps growing been a fan since your home in Hawaii with the 07 as the only truck. Really cool that you have the same sponsors as the big channels. Keep the content coming. Bring back your camera man too!! Tell the camera man the strike is over. Lol

@LonestarHawaiian

Ай бұрын

🤙🏽 THANKS FOR WATCHING ALL THIS TIME!

Put in a traditional garage door and add a couple more panels to add more height. much cheaper

Really great seeing progress’s thanks for the uploads man.

It’s looking great!

I commend you for your work ethic and your ingenuity!

Wading through the pond is one way to clean your tracks off

Wow looks so good and I’m sure you are super excited and tired!😂 Don’t worry about the upload frequency. We realize the daily grind. Every upload is a treat. Keep up the great work!😎

Building is coming together nice and I am sure you will make it look good at the end.

Looking good! For the doors… why not buy 2 standard doors at $3500 each and then stack them?

It’s coming along nicely.

Great progress!!!

I Am Absolutely Loving This Garage Build, You Are Doing A Great Job

Mad respect for your hard work! 💯 😎

Green Hinge Garage door system to help seal door.

I like them garage doors with the windows in the side too Awesome

The paper on the zip system is pressed with the mat of waffers so its technically glued as well just different process/paper Huber uses. I worked for Huber when they were test running the zip board.

Sarge is a definite trooper. Nothing like Ohana when you need help. 🤙🏼😈🤙🏼

Chad, brother… you are BY FAR one of the very best and MOST entertaining dudes on KZread! 👏🏻👏🏻👏🏻👏🏻 I wait patiently each week for you to drop your video and video shorts. Go with the garage door with the windows, just cause they look cool! Keep up the great work, brother! Next time you need windows, hit me up.

@LonestarHawaiian

Ай бұрын

🤙🏽🤙🏽

Juuuuust a little bit of rain…. 🤦🏼‍♂️😂 🌧️

Not only are zip sheets expensive...you'll get quite the sticker shock when one calculates how much the tape cost!!!

Build a small loft over the door so you can put up the track and increase your storage in what would be dead space. Malama pond, a hui hou

Looks fantastic

It’s coming along!!

The shop is looking good brother

Can’t believe how bad your weather is. I just thought Texas was hot and dry!

It looks awesome!

Garage is looking good, keep up the good work

Thanks for doing these videos. I'd assert moisture is the biggest test for siding--especially for those of us in wet environs.

Get the side mount motor for your garage door not a roof mounted one!!! A side mount will allow the track to get significantly closer to the roof

The eclipse is cool, I’d like to go to Hawaii and witness Lahaina Noon

I think you should do a 10 foot high door high lift at 3 to 4 feet whatever you can that will fit your wall hight. The door will sit in the high lift so it won't be 10 feet back into your shop giving you more room for car lift clearance. If you do a 14 foot door it will be 14 plus into the shop plus if you use a trolly opener that will be another 2 to three feet. I'd use a jack shaft opener lift master makes a 98032 that is made for bog heavy doors or the 98022 would work great on a 10 or 12 foot door. Just my advice.

Full glass doors!! Like a fire station

Dope video man!! Subscribed!!

If you put a bit of oil on the nails before closing the gun, they shoot well into the wood taking a touch of oil with them.

Almost done. Can't wait for the next one right next door to it.😊😊😊

Sir. You are doing a fine job!!!

i bought the same force field for for walls and roof and used the yellow tape on everything also the liquid flashing is great for along the bottom and nail holes but had to order it off amazon couldnt find it anywhere else ....also got my boards at the cheap price before it jumped. mines a 40x40x13 2x6 walls. our code wouldnt allow a metal frame. loving the progress and keep it up my guy.

Some shed that that’s big but been watching and it’s coming together now looking really good wow 😊👍🇬🇧

Welcome back 808.

12:00 wow damn the weather was crazy!

Since you plan on a black ceiling. You should consider painting or powder coating all your garage door track and hardware black before installing them. Also when shopping for a garage door make sure that the windows are insulated glass. In Michigan we have a 14x14 insulated garage door. But the windows are only single pane glass.

Make sure you go with high lift tracks and direct drive opener. It would be so much cleaner and operate so much better for not much more money

Shop is looking good

Well for the durability testing house have stucco or other types of siding that make the exterior wall stronger