Enjoyed the video, look forward to the future SD1 videos 👍🏻.

I hate to say this Sheldon but if you want a clear conscience when you sell it and even more money for it then you need to overhaul the whole top end. Valve grinding, cam inspection and new lifters. Then possibly the same on the other side. It is very unusual for hydraulic lifters to bend a push rod like this unless something else happened. On the plus side this car is definitely worth the effort! Good luck

@classic_britain

2 ай бұрын

I don't need to overhaul the entire top end that's abit much and I don't have the money to do that but I will be honest in the advert about what's been done to the car!

Lovely hot day. Great cruise.

If that was an old transit di push rod it'd be straightened out on the roadside & put back in as good as New 😂

Hi Sheldon glad you've finally got to the bottom of the problem, looking forward to hearing it running without the tick ✅ lol 😂 cheers 🥂

So glad good sense finally prevailed and you did what is a relatively easy job and immediately found the main issue. Pity you still have to sell it on but at least you can do so knowing what the issue is and the car may well run fine for some time before needing a more complete overhaul. This is also the kind of content I think many subscribers enjoy as it really shows what’s involved in running these classics.

If i had called my Mother a muppet my arse would not touch the ground for a week ...bit more respect please

@classic_britain

2 ай бұрын

Relax we say far worse then that to eachother lol!

@billhigginsbottom2191

2 ай бұрын

@@classic_britaindon’t make it right tho bro

@corvair140

2 ай бұрын

@@billhigginsbottom2191 Exactly. No respect these days with kids. If I dare to say that to my mum, I wouldn't have been able to sit for a week.

I bet your neighbours love your car collection 😂😂😂

@classic_britain

2 ай бұрын

What 2 cars?

Good result, I look forward to seeing the P6 fixed

My dad's had same problem in the 70s and the rocker had seized on the rocker shaft, check it is free as will bend the push rod, common even back then, good luck.

Masters at work . Not the end of the world for sure.

Another good video 👍👍👍👏👏👏

Great episode, comforting to see some of the old Sheldon coming back, any chance of adding Toad at some point, the 3 of you were simply classic.

Always nice to get recommended a video from this channel, that’s one hell of a bent pushrod tho wow. Those SD1s are so iconic looking, what’s Basil up to?

To bend a rod like that with a hydraulic lifter, I would have to guess that the lifter was initially stuck in the fully retracted position and the top of the pushrod then jammed against the side of the rocker which meant that on the next stroke the valve spring either became coil bound or the piston hit the valve. As the valve does move and turn, the valve spring probably became coil bound but I would either check the top of the piston with a borescope or hammer the pushrod straight (or use an old one) and do a quick compression test. The question is then whether the lifter has now fully freed off or not. The straightened/used pushrod will allow that to be determined that as well, either by measurement or using the compression tester. Also, check the rocker for damage. Richard

This is not unusual at all on an older engine that sat for awhile I bought a 64 thunderbird last year with the 390 engine that had been sitting for three years. I tried starting it and it bent two pushrods. I used a rubber hammer on the affected valves and broke them loose. I ordered two replacement pushrods from Rock Auto put them in and all good. I have driven it for 8000 miles since then with absolutely no issues. I truly believe that if you replace the bad pushrods someone just drives the car for a year or so everything will work out fine. I don't know. how hard those particular carbs are to tune but that would be the only issue. Everything else is just basic old technology. Best of luck on selling it and now you will be able to be confident on the condition of the engine.

"Someone's got to hold the camera ! " Looooooool 😅🤸🙃🤸🤣🤸🙃🤸😄

Great video Sheldon, Looking forward to the SD1 content, Straighten that push rod with a hammer it will be fine.

Are you going to check the lifters just in case there's more than one that's stuck you just know what will happen nice new push rods and you might end up with the same result bent push rod again . really enjoy your videos 👍

@classic_britain

2 ай бұрын

Yes I will check them

Something like Seafoam might free the lifter, but new oil alone is unlikely to.

Sheldon,The push rod is the weak bit and the sticky valve is causing the noisy lifter..Hit the top of the valve that's stuck, squirt some wd40 down the valve guide...normally an easy fix..and put the push rod on a flat surface ,like the back of a vice and hit it straight with a club hammer.

@TheClockwise770

2 ай бұрын

Sound advice I don't think. If he follows your advice he could do more damage 😂

@TheV8nutter

2 ай бұрын

@@TheClockwise770 Worked for me !

Don’t drop a lifter down inside because it will sit on the crank and when you crank it ,it will jam between the crank and crack the block ,there hydraulic lifters check your cam lift on the rear lobes for lift as they wear

Greatcontent. Are you interested in car accessories sponsorship?

🤣🤣as straight as Philip ...............

Hello I expect someone startef engine with a stuck valve ,but a new push rod should fix it.

Starting at 0:54 you spend a long time letting us look at the steering wheel. But I think you should have spent more time as we could not understand if that was a steering wheel or a big pie. Why did you spend so much time showing the steering wheel?

Unless a piston comes through the block then all is fine with the engine 🙂.

Hi Sheldon , can you reach out to Ben at Tasty Classics looks like he needs some help from you, regarding a P6 thanks

@classic_britain

Ай бұрын

I have done don't worry

@AUCHTERMUCHTYZZ

Ай бұрын

@@classic_britain Thanks Sheldon take care

I'd bend that straight and try it out before putting another one in, and bending a new one!

@classic_britain

2 ай бұрын

It won't the lifter is not stuck plus I have SH ones I can try!

You dont seem to have any luck with all of these P6's you have bought. It may be time for the five year old reliable and running Toyota Yaris so you may finally get on the road.

Keep it and fix it

SD 1.... you'll be competing with Nitro Silver 🤐

Like and subscribe, Loathe and despise