I’ve never been so interested in bottle jacks. This guys good.

@tcalcut

2 жыл бұрын

Same here

Buddy. You just answered every single question I have ever had about bottle jacks. Thank 👏🏻you 👏🏻Sir👏🏻

Excellent commentary! Thank you. I learned quite a bit.

I have an old sears 2 ton jack that is just the smallest thing I have ever seen. the seals rotted out on it years ago and all the fluid ran out, but I just filled it with some really thick transmission fluid that's more like a gear oil, and tried it out and it still lifts the front of my truck effortlessly. I was amazed by that little thing. I thought it would struggle a little bit, but no it stayed strong and didn't drift at all. I mean it's still well within spec but for how old and rotten it is, it's no slouch.

You can use a bottle jack axle lifting saddle to lift the vehicle from a solid axle as well.

This inspired me to go take a look at the factory bottle jack in my 2009 Mitsubishi Express/L300 Van here in Australia, which I've never needed to try out. To my surprise it's also a two stage bottle jack, and the first one I've ever seen too, I think it must be a Japanese car maker thing. It's a very small orange bottle jack almost identical to your orange one, also 1500kg rated, but the bolt down hole is closer to the corner of the base, the base is also plate steel just like yours. Collapsed height is 6-1/2" and with both stages fully extended it measures 15" total height. Interestingly mine extends the narrow ram first, then the wider one comes up second. Also, the narrow ram collapses first, before the wider one....ahhh hydraulic jack trivia...love it🤣👍🇦🇺

Very educational. Good teacher

Another great video! Thanks!

@CatusMaximus

5 жыл бұрын

:)

Check out the current Ford Truck bottle jacks. They are also 2 stage.

the seals in the seal shop are playing black jack?

Awesome video! I've been curious about that 20 ton just to have around.

@CatusMaximus

5 жыл бұрын

The newer bottle jacks from Harbor Freight or better than the old ones

Thanks cool video

@CatusMaximus

5 жыл бұрын

Thank you

I had on of those two stage bottle jacks fail on me a couple weeks ago!!! Thankful I was using it properly, had a flat and it would only fit it in middle of the chassis rail because the tire was to low to the ground so I lifted it about 2 inches then it came down in a blink of a eye. Then I was sitting around waiting on AAA. And another time I had it almost fully extend lifting a cab wit no chassis it it fell right over to the right again thank God I wasn't in harms way

@CatusMaximus

5 жыл бұрын

Good comment an example of why you have to really respect little bottle jacks and lifting up heavy things in general

My 2006 Dodge sprinter came with a 3 stage hydraulic jack.

That orange 2 stage jack is found in Mitsubishi Montero’s from 1984-1999. Possibly even after 99 but I’m not completely sure. I’ve owned 8 Montero’s but only one was a latter one (2005) and I didnt get to check the included Jack.

@simonilett998

Жыл бұрын

I have a late '93 Mitsubishi Pajero here in Australia, same as a Montero/Shogun, pretty sure it has the factory jack, so I'll have to check it out tomorrow. I just looked at the factory jack in my 2009 Mitsubishi L300/Express Van and to my surprise it has pretty much the exact same two stage orange jack as he showed in this video, I think it must be a Japanese car maker thing.🤣👍

@IDIturboDiesel

Жыл бұрын

@@simonilett998It's called a double ram jack. Ford Super duty trucks come with them as well but it's yellow and it's 4 ton.

@ronfox5519

Жыл бұрын

@@IDIturboDiesel sounds perfect. Something to keep my eye out for at the junkyard.

My 2017 Toyota Tundra came with similar 2 stages bottle jack like the one shown in this video.

My biggest issue is having to crawl under a truck that only has jack points way under to twist the release lever. The pumping tool Is not long enough for some vehicles. Any tips

@jameshill4900

Жыл бұрын

I use a scissor jack. Mine is an older GM truck one that has a 4 foot long handle that hooks on the jack and allows you to safely push it under the vehicle. Extremely low profile as well for cars. I am surprised they aren't more popular.

Do you have any brand information of the red jack? I know a Japanese company call Masada makes 2 stage bottle jack, but they only have 1.5 tons or 3 tons, not 2 tons type.

@johnswimcat

Жыл бұрын

Search for "telescopic bottle jack". Plenty available here in the UK, different makes and sizes.

I recently bought a pretty good (I thought) bottle jack for my jeep but I keep it in a canvas bag, stored on it's side and it is leaking. Would all bottle jacks leak when stored on their sides or do i have a lemon? Thanks, cuz it seems no one on youtube addressed this issue.

@CatusMaximus

2 жыл бұрын

It is an issue with bottle Jack's some leak when stored their side, some don't. They do not have the same upper piston seals like heavy equipment cylinders. They also Caan leak from the rubber fill plug on the side.

That little 2T screw looks like it could barely support a chair

I have that exact same orange jack. I turned it into a toe jack, but it gave out on me and is now leaking all over my garage. Came here trying to figure out if it was possible to repair it.

@CatusMaximus

3 жыл бұрын

It might be possible but you need a huge wrench or socket to be able to unscrew the top of the jack and pull out the piston and replace the seals if that's where it's leaking, it may be leaking from the valve or the pump.

How high does a 7 ton Masada MH7 lift. Can one lift the car high enough for maintenance or just tire change; of course with jack stands

@TinyBuddha604spoonr47

3 жыл бұрын

never do under car maintenance with bottle jacks. Only tire change.

Masada still makes a range of 2 stage jacks. Search online.

What happens if you store Masada bottle jack on the side? Does it get irreparably damaged.

@CatusMaximus

4 жыл бұрын

No it does not break a bottle jack by storing it on its side. Many bottle jacks can actually even be operated while on their side the pump just has to be facing the top

I'm a tow truck driver and use a low profile jack but I run into trouble with trucks especially lifted trucks with big tires

@melindaortiz9741

2 жыл бұрын

Stack wood under the jack

So I was thinking of replacing my factory scissor jack for one of these because mine failed on me. I take it that these bottle jacks aren't good for replacing a flat?

@jameshill4900

Жыл бұрын

My suggestion would be get a heavy duty scissor jack. I use an older GM one that came with their 90s trucks. Mine has a long 4 foot handle that attaches to slide the jack, is cupped for safety, and is extremely low profile.

real short 18 minutes

@BigWheel.

2 жыл бұрын

And 40 seconds!

Can you recommend a jack that's fast? I need one which moves quickly but don't need huge amounts of power - for a cider press and most are super slow cycling. thanks!

@CatusMaximus

3 жыл бұрын

A Double Pump Floor jack piston

@ronfox5519

Жыл бұрын

Screw jack ran by an impact wrench. Scissor Jack's are nearly free at your local junkyard.

I found one in my car, I've never even knew I had one

How much lift do I need to change a tire on a 2014 Honda CR-V? The frame is 10.5” off the ground. I’ve noticed that the travel on these jacks are about 7”.

@CatusMaximus

5 жыл бұрын

Generally speaking when it comes to SUVs like that bottle jacks just don't have enough lift to get past the suspension travel you really need a little floor jack of some type that has a lot of travel

@Camrographer

5 жыл бұрын

I bought the Harbor freight 6ton bottle jack. It has a lower profile that the others. I'm confident that it will clear the body now. @@CatusMaximus

@thisisyourcaptainspeaking2259

4 жыл бұрын

@@Camrographer One concern with jacks is if the tire is flat, there may not be enough space remaining to insert the jack underneath, safely. Single ram hydraulic jacks especially but also dual ram bottle jacks might also present this problem. Be sure to confirm before getting stuck somewhere where you might compromise safety, damage your vehicle, etc.

@Camrographer

4 жыл бұрын

@@thisisyourcaptainspeaking2259 I tried it out on the car frame and made an allowance for a flat tire.

@thisisyourcaptainspeaking2259

4 жыл бұрын

@@Camrographer Great, yes the crv does have good ground clearance.

So these aren't good for changing out a tire of a pickup truck?

@CatusMaximus

5 жыл бұрын

Yes you can use them to change your tire on it vehicle with an axle it's that they have a narrow base and are unstable

Hi, should you store the jack with the release valve open or closed? Cheers 🍻

@horaciocastillo1435

2 жыл бұрын

Lightly closed is recommended

Quite the video!

Torin jacks are well made. I have a few of them 12 ton, 20 tons, and a 50 ton

@MrRepid

2 жыл бұрын

Curious to what you use a 50 ton one for

@Azeminad

2 жыл бұрын

@@MrRepid probably leveling a house.

@MrRepid

2 жыл бұрын

@@Azeminad that's crazy

@ronfox5519

Жыл бұрын

@@MrRepid And machine work as well. Also, it's nice to use oversized Jack's for the peace of mind that comes from the extra strength and stability.

Those things are dangerous. I thought about getting myself a bottle jack because I like that it’s so compact. But that was until I saw a video on KZread where a guy demonstrated how one tip over and slipped out from under the car frame. The problem arises that the base is fairly narrow and if you have any horizontal force applied from the frame, it can slip right out from under the car

@jameshill4900

Жыл бұрын

I use an older GM truck scissor jack that came with their 90s trucks. Mine has a long 4 foot handle that attaches to slide the jack under the vehicle safely, is cupped to prevent slippage, and is extremely low profile for cars. Much better than a bottle jack imo.

@Gaba-oo4qb

Жыл бұрын

@@jameshill4900 I prefer the small wheeled jack.

@jameshill4900

Жыл бұрын

@@Gaba-oo4qb Definitely much safer than a bottle jack. I've had trouble using them in low profile cars but it sounds like it's working well for you 👍

How can a welded jack be repaired/rebuilt?

@CatusMaximus

4 жыл бұрын

Not really it's totally not worth it to cut out the weld fix it and then reweld it

@hishamchohan494

4 жыл бұрын

It can be repaired, Brand like mega spain jacks Japanese jacks

@thisisyourcaptainspeaking2259

4 жыл бұрын

@@hishamchohan494 How is it repaired, just wave a magic wand and poof, it's magically working? Seems it's welded so this means cutting it open then welding back after repair. It's often difficult or expensive enough already to locate parts, let alone the time involved cutting and welding.

@hishamchohan494

4 жыл бұрын

@@thisisyourcaptainspeaking2259 you don't have to.cut it. Just use hook and needle tools to remove that lock ring on the top of the ram/

@hishamchohan494

4 жыл бұрын

@@thisisyourcaptainspeaking2259by the way ,what brand or model or ton it is?

Do you perhaps have any idea of how tight that nut on the 20 ton jack would be generally? I mean how much torque would you need to screw/unscrew it in Nm or lb-ft? Thanks for the video!

@hishamchohan494

4 жыл бұрын

Just use a pipe wrench

@thisisyourcaptainspeaking2259

4 жыл бұрын

I have broken loose the nut while the weight of a car was supported by the jack. A large wrench or even pipe wrench, expect less than 50ftlb should be plenty. All those I've disassembled had right hand nut threads.

@hishamchohan494

4 жыл бұрын

@@thisisyourcaptainspeaking2259 make a video and up load it

@ronfox5519

Жыл бұрын

@@thisisyourcaptainspeaking2259 50ft-lb?? While under pressure??? Sounds very unlikely. Does the pressure somehow reduce the torque needed?

@thisisyourcaptainspeaking2259

Жыл бұрын

@@ronfox5519 The hydraulic pressure isn't (and ideally should never be) against the cylinder gland nut. The purpose of having the hydraulic cylinder under load (the jack under pressure) is to keep the jack from spinning while loosening the gland nut. You should always avoid extending the cylinder to it's upper travel limit where the gland nut is receiving hydraulic pressure because this pressure can rise dramatically beyond the capacity of the piston seal. The jack may also be placed in a jaw vice while removing the gland nut, if one is available. Bonus tip: keep top of jack covered and cylinder in home position while not in use to keep dirt and debris from collecting on the piston rod and entering the cylinder. I place a plastic bag, rag or paint spray can cover over the gland nut for this reason. You may notice many jacks no longer have a removable gland nut. Personally, I avoid these disposable jacks.

It's a grower not a shower

Fake?? Found in the market here Mamada bottle jack on offer and claims Made in Japan. Is this fake? After watching your vid I bought 7 ton Masada. This Japanese company has been making bottle jacks since 1946; gives me confidence. It costs me about US$27. Will a

Quick video?? Almost 20 minutes...