WISH I HAD FOUND THIS VIDEO EARLIER!!! My 51 would not hold a low idle. Then bog when I hit trigger. No real impact when adjusting carb. Chainsaw was given to me and I did not know how it was maintained prior to me recieveing it. Carb looked clean, so I assumed old gas mucked up the insides. Bought new carb ...Could not adjust that one either. Checked the fuel line at the problem area you highlighted in this video, found cut in line, replaced line and started it up. Holy Hell! saw startled me it started so quick and rev`d so strong........No carb adjustment needed.. Thank you for taking the time to make this video.

I followed this today for my 39 year old 254. No more leaking on the shop floor. Thanks!

Awesome, to the point. Took me longer to get the fuel filter on then to install the line on my 350. Thank you!

Thank you very much.... just repaired my 357xp with the help of your videos...........soooo great !!!!!!!!!

After further checking on my 288XP, I found the line goes straight down through that top plate, that mweba1 seemed to be working under. I have a little rubber grommet that protects the line as it come up to the carb but otherwise the procedure is very much the same. I now have my new line in place, with the filter attached, and the line is now on the carb. Thanks for the help this video gave me.

Thank you for your advice. I just replaced my fuel line and it was very easy and quick

@juniorcromeans7204

2 жыл бұрын

Y

Thanks for this - I couldn't work out how on earth to get the fuel lines into the tank!

@TDHReviews Last summer I ran 50+ gallons of fuel mixed with sabre through one saw. I have no complaints other than I can no long purchase it locally.

Great video. The angle cut is the trick.

My Husq 51 is leaking gas and yes the fuel line feels hard as a rock. Thanks for the vid, I'll replace the line pronto.

Thank you ....greetings from Germany Peter

Thank you, sir! Great vids!

@mweba1 The shop i work at sells all amzoil products so thats where i get mine, they use amzoil mixed gas in all there stuff including 4 cycle and theres no problems. Its smokeless, doesnt built up carbon, 100:1 is good for all engines, just all around a great product

The line is a specific size. If it does not fit tight into the tank it will leak. Oregon has a 3/16 that is the most common for people to use but it is to small causing a leak. See this weekly.

No problem. Bent nose 7" MPC7A 10" MPC10A

I am working on a model 288 Husqavarna. Although some complain about this fellows hands being in the way at least at the 2:00 minute mark I now at least know where and how to look for that spot to insert the new line. Mine has a rubber grommet that the line comes up through to the carb. My line was so rotten I could not see where it came from. I think I still have a piece stuck in the hole into the tank, but now I know where to look for it. Thanks.

That's exactly where my fuel line failed, I took it loose from the carburetor and it was nice and flexible, look in great shape but right where it goes through the entrance it's only hanging by a thread.

These pliers look dang handy. More like surgeons equipment, but ideal for the job. Just had a struggle with a chain saw fuel line this morning!

@jamesgwynn574

6 күн бұрын

Hi , I’m replacing my fuel line and need the pliers like the one he’s using , can you help me find a pair ?

Thank you for the great info! Just a quick question, the "blue points" that you use in the video . . are they a Blue Point tool from Snap-On? If not, where do you get them?

You will want to inspect the tank vent and fuel line. If you crack the gas cap open a hair will it continue to run?

Thank you, sir.

I see you have a bottle of Amzoil in the backround. I use that stuff as well its the best out there

Yes they are sold through Snap-On. Great locking needles.

Hey Big Guy.... Is the 350 carb upgrade a carb from the 359? Or can you hit me up with a part number or source if aftermarket available? Thanks much! Keep rocking out these killer videos...man! Great stuff all around!!! A++++ Thanks again, Big Dave

Would a crack in the gas line cause air to fill the bubble? Thanks for the video.

I have a Husqvarna 136/141 recently discovered that the line broke off at the fuel filter so do I just attach new line to bottom of the other end of the interior piece hanging down inside the fuel tank?

I have a 345e. Now on your video you are informative. I have one question I had my boss replace the line feeding from the primer bulb to the white nipple. Now when we poured gas in the gas ran out everywhere and when i tried to prime i got nothing in the bulb just gas pouring out. Is the husky gas line specific in size? i got 1/8 gas line... or did he put it into the breather and not the right spot? hope to hear back thanks

This was wonderful!. Please also address fuel tank vent and filter plug that go together. They appear to be on the diagram on parts tree website, but do not exist in my model. Is it possible that 372 doesn't have a vent? If you know of course.... Fuel tank vent resembles approx 2 inch long multidiameter straw

do you have the fuel routing for a 240 husqvarna removed lines and catching hell getting the fuel line routing correct

Wan't quite certain where the fuel tank hole was as I have not removed the carb yet. Thanks

7" MPC7A 10" MPC10A

How does the fuel tank get its vent air? I have a 266xp and put a new carb, fuel line and filter on it and did the initial settings on the carb and it will not start with out priming it, then runs up the rpm then dies like it's run out of fuel. Does the carb suck fuel into it, or is it pumped in somehow? I've tried a few things and I'm about to give up on it... Any help would be appreciated.

@markusgarvey

6 жыл бұрын

The cap has the vent. I know it's 2 years later, but better late than never!

You mentioned that it'll burn up the cilinder if the fuel line is damaged,why is that?i think I'm experiencing that on my husqvarna 365

Can you tell me where the vent line goes there? mine has 3 lines and leaks when i lean it on the side to fill the fuel. thanks,

@byronschroedel432

3 жыл бұрын

Did you ever figure it out, dealing with the same problem?

I have a problem with my Husqvarna I cant figure it put why the fuel is not coming out of the tank on that Little tube it have no cracks how you explain how the gas come out from tank ? Thank You very much

mweba1 I have a 455 Rancher that has a leaking fuel line. When I ordered the replacement it is coming in two pieces. How does this go in as opposed to the model you are demonstrating?

@mtsflorida

Жыл бұрын

I have the same model. The fuel line works the same, however with a purge bulb you need the yellow line to connect to the tank vent and the other yellow fuel line to connect to the carburetor that has the port on the bulb side as opposed to the inlet port on the fuel hole next to the vent on that right side closest.

i have husqvarna demo saw k970 im not sure, but it has a fuel manual pump, it start but few minutes its stop when i look on the fuel pump empty? what will be the problem ? thanks

what is the name of the plier like tool that you use. Thx.

I have a zenoah gz400, and saw works only in one position. If i turn the saw on right side, she turns off after view seconds. I looked in fuel tank, there is a filter there, it stays allways in one position, no matter how i turn the saw? What to do?

I have a Husqy 345 and the fuel filter looks bad but the hose, new. I'm going to try it with a replaced fuel filter only, first. How did you detach the hose from the engine end? What's happening is that the engine dies when I apply gas especially on horizontal cuts, like on a tree stump. Can you help?

@stilo398

8 жыл бұрын

+stilus looks like I found the problem-- thanks for the youtube.

Can someone help me. Just today I noticed my 372xp OE leaked fuel when tipped on the bar cover side so I took off the handlebar and I took out the bottom screw and it started pissing out gas out of the bar mount hole

Hey I have a jonsred 2150 turbo that has a broken muffler bolt stuck in the carburetor is there anyway to fix that

@zeiboturangers

7 жыл бұрын

Take it to the service, otherwise it may be difficult to remove the bolt on your own. For the muffler I suggest you can buy a muffler support bracket that is for 346xp, cut the right hand side support, bend the bracket so it fits the saw.

I want to see where all fuel and vent lines connect from gas tank to the carburator 372xp

What's part # on fuel line hose ?

How the fuel line back to the tank.

How about a video of the other 2 lines going and coming from the purge bulb of the rancher 455.

my 235 e will not tick over for love nor money ,, it will rev to the max , but thats it ,, would this be the direction to look thanks t

@susieq72

Жыл бұрын

carb settings would be my bet

Ugh. I have a 55 that the hoses are rotten. The Stihl is superior with replacing the hoses.

Would have been really nice if you would have moved you hand out of the way so we could actually see what you were doing.

@mweba1

6 жыл бұрын

Jon M if you can't figure it out from this presentation, I can't help you. You're welcome for the free tutorial

Only thing that ever happened to my 359 is the fuel line.

i have a 350 husqvarha chain saw when you give it gas it will dead what is wrong with it lput new fuel/carb on it

@mweba1

9 жыл бұрын

Likely an air leak. I did a complete saw tear down rebuild video.

Stihlms180

Don't bother showing anything there guy... not like anyone needed to see.

That’s not the real fule line

Can't see with your arms in the way and not very informative

@mweba1

7 жыл бұрын

Apparently, you weren't listening.

Don't bother watchin . This guy stands in front of half of what he is trying to film and mumbles; this is F'n useless

@mweba1

7 жыл бұрын

john greenman What video are you watching? Ears need a good cleaning? Thanks for watching.

@muckeyduck3472

6 жыл бұрын

Same comment I made dude.

@SurvivalRussia

6 жыл бұрын

I find your videos awesome :)

@Ritalie

5 жыл бұрын

This was a very helpful video. Thank you!

@tonyvalencia1000

3 жыл бұрын

The video was vey helpful to me