I use these. They are a little more aggravating to install than the OEM grommets. However, they're better because they fit much tighter.
@z-man17634 ай бұрын
Thank you. I got the grommets handled they did great. Installed new carb off Amazon, Chinese junk. Saw overspeeds and is unadjustable. Will be returning that. Do you have a source for a decent carb?
@christophercorbett7307
4 ай бұрын
It's unadjustable? There should be an idle screw adjustment, along with two small flat head adjusting screws. They'll have a plastic guard on them. Just pop them off.
@z-man1763
4 ай бұрын
The caps are off. Used a 20 spline tool. By unadjustable I meant turning the screws made no difference with RPM teaching so high I thought I would blow the cylinder, this was with no throttle. I closed them fully, opened 1 1/4 for both along with the idle screw. Still full Rev. I pulled the carb today and checked the tool directly on the adjustment screws to be sure. That's why I felt the carb is no good and asked for another supplier source. Thanks again.
@christophercorbett7307
4 ай бұрын
You need to richen the mixture. The low side screw (closest to the engine) turn it out (counter clockwise) this will bring idle down. The problem could be an air leak which simulates a lean condition.
Пікірлер: 20
Bro all video instructions should be done just like this one. Great explanation. Thanks so much!
@christophercorbett7307
2 ай бұрын
Thank you so much!!
Great description, I wasn't sure on my primer bulb lines, thanks for all the details..
@christophercorbett7307
Күн бұрын
Yes sir so glad it helped
You explain it very well and it’s easy with the proper tools 😊 Thank you 🙏
Great instructions
Thank you! That was exactly what I needed.
@christophercorbett7307
26 күн бұрын
Good deal man!!!
THANK YOUUUUU! Great video
@christophercorbett7307
Күн бұрын
Your welcome my friend
Just don’t use impack tools to install is best 😊
Really good video. Question. Is the fuel hose you used all the same size?
@christophercorbett7307
19 күн бұрын
Yes sir it is. I use what will fit most tightly without pinching. Helps reduce chances of leakage as the lines harden
Great tips thank you! Could you give us the info on the kits you used? Maybe some links for the parts please. I want to replace my grommets also.
@christophercorbett7307
4 ай бұрын
www.amazon.com/Grommet-Compatible-Husqvarna-570EPA-Chainsaw/dp/B09JSR12X9/ref=mp_s_a_1_3?crid=2HI70H83Q4LZ7&keywords=chainsaw+grommets&qid=1705992452&sprefix=chainsaw+grommets+%2Caps%2C130&sr=8-3
@christophercorbett7307
4 ай бұрын
I use these. They are a little more aggravating to install than the OEM grommets. However, they're better because they fit much tighter.
Thank you. I got the grommets handled they did great. Installed new carb off Amazon, Chinese junk. Saw overspeeds and is unadjustable. Will be returning that. Do you have a source for a decent carb?
@christophercorbett7307
4 ай бұрын
It's unadjustable? There should be an idle screw adjustment, along with two small flat head adjusting screws. They'll have a plastic guard on them. Just pop them off.
@z-man1763
4 ай бұрын
The caps are off. Used a 20 spline tool. By unadjustable I meant turning the screws made no difference with RPM teaching so high I thought I would blow the cylinder, this was with no throttle. I closed them fully, opened 1 1/4 for both along with the idle screw. Still full Rev. I pulled the carb today and checked the tool directly on the adjustment screws to be sure. That's why I felt the carb is no good and asked for another supplier source. Thanks again.
@christophercorbett7307
4 ай бұрын
You need to richen the mixture. The low side screw (closest to the engine) turn it out (counter clockwise) this will bring idle down. The problem could be an air leak which simulates a lean condition.