Thank you.. You make Electrical repairs make sense to the novice. God bless you all.🤓👍

@AskTheElectrician

2 жыл бұрын

Thank you Richard, Glad to help!

I have an older home and your video answered my questions about grounding. I will pick a different location for my GFCI.

@AskTheElectrician

6 ай бұрын

Glad I could help!

Thank you. You are very good at covering salient points related to the GFCI. I just protected my family with your assistance. Bless you!

@AskTheElectrician

5 ай бұрын

Thank You - I'm Glad it was helpful for you and your family!

Thank you! This is just what I needed. Great video.

@AskTheElectrician

3 жыл бұрын

Glad it was helpful!

This video was very helpful. My Aunts house is an older home built in 1945. And it seems to not have a ground. I appreciate your time.😎😎

@AskTheElectrician

3 жыл бұрын

Not when it is done correctly.

@waynewaters4537

2 жыл бұрын

Had a fuse panel in my garage that was condemned by the insurance company Georgia Pacific. Had fuse panel installed inside because of code changes had to move main shut off outside. Electricians added a panel underneath my electric meter. It only has three Breakers a 30 amp double pole for my generator a double pole 20 amp for my pool pump a 20 amp single pole for my pool light which or both GFI. The problem I'm having every time you touch the fuse panel the gfi's trip. I replace the wiring for the pump and the light because it was in cast iron piping and rusted-out. You can literally touch the metal cabinet and the breakers will trip. Trying to figure out because all the breakers are still inside the garage is that considered my main cabinet or is that the sub-cabinet from this one with the main shut off. This one has the neutral and the grounds tied together no separate Ground Bar. Any info would be greatly appreciated. Thank you

Only video out of the many that I watched that fixed my gfci install issue. Thank you.

@AskTheElectrician

6 ай бұрын

You're welcome!

Great video that answered most of my questions. Currently remodeling a bathroom and the old outlet will now be too near the new sink, so I'm having to move it at least a foot away from the sink. The house is not grounded so I was looking for info about installing a GFCI in the bath to replace a standard outlet. Thanks for the informative video on this subject.

@AskTheElectrician

Жыл бұрын

Glad it was helpful!

@glasshalffull2930

Жыл бұрын

John, if there are other receptacles on that circuit (another bath, bedroom, garage,etc), then the GFCI receptacle should replace the receptacle that is closest to the breaker panel. This gives GFCI protection to everything downstream on that circuit. This is actually a manufacturer’s recommendation. To meet code you need to label all the faceplates downstream with ‘both’ the “GFCI protected” label and the “No equipment ground” label.

Great information thank you for helping so many of us learn

@AskTheElectrician

2 жыл бұрын

Your Welcome!

Great video for the DIY, it's insane how much handyman work is done out there, wouldn't be a problem if it was done the right and safe way. Some are very dangerous to the tenants.

@AskTheElectrician

Жыл бұрын

Well said, and I am glad you enjoyed the video.

@teamjj153

9 ай бұрын

Got same old house, installed a gcfi with 2 wires but the little green indicator light don't come on , any idea why it's not on?

Some older homes from the 50’s and 60’s have a shared ground wire running to the bathrooms and kitchen, but the ground is combined with the neutrals in the sub-panel (sub-panels of this vintage typically did not have a ground running to the main panel). I’d say in this case it’s OK to use the ground wire when adding a GFCI outlet and the homeowner should consider a sub-panel upgrade or add a bonded ground bar in the sub-panel with a ground running to the main or metal water pipe (main panel of this vintage were typically grounded to the water pipe entering the home).

@AskTheElectrician

5 ай бұрын

It is always best to upgrade the wiring system and have the required grounding installed according to current codes.

Very good explanation of what was happening and what to do and what not to do clear and concise subcribed. Thanks

@AskTheElectrician

6 ай бұрын

Thank You - Glad it helped

This video in priceless. Thank you.

@AskTheElectrician

2 жыл бұрын

Thank you very much Matzi!

Thanks. I always wondered if a GFCI would work without a ground

@AskTheElectrician

2 жыл бұрын

Happy to help

Thank you for the great lesson

@AskTheElectrician

2 жыл бұрын

Glad you liked it!

Excellent Information thanks alot 👍

@AskTheElectrician

2 жыл бұрын

My pleasure

Good teaching video. Thank you.

@AskTheElectrician

2 жыл бұрын

You are welcome!

Wonderful explanation and practical examples given.

Great video !!!

@AskTheElectrician

3 жыл бұрын

Thanks!

great video!

@AskTheElectrician

3 жыл бұрын

Thanks!

Great video answered my question about 2prong recept. replaced with a 3 prong receptacle. the ground was connected to the neutral side. Still when testing with a my tester from hot side to ground I still read 118 volts . I was told this is a safe way they use to change 2prong receptacle to 3 probg receptacle

@AskTheElectrician

Жыл бұрын

Just be sure that a jumper wire is NOT installed between the ground screw terminal on the outlet and the neutral of the outlet, as this is not allowed.

This video was excellent. Thank you so much!

@AskTheElectrician

Ай бұрын

Thank you for watching!

great video well explain thanks

@AskTheElectrician

2 жыл бұрын

Thanks JR, Glad it was helpful! See more at ask-the-electrician.com See you there!

Wow, I had not seen the bootleg ground, but it's something to look for... thanks!

@AskTheElectrician

3 жыл бұрын

You bet!

@BestLittleStudio

2 жыл бұрын

@@AskTheElectrician If I am correct, one of the bootleg ground circuits is just a death waiting to happen. Handyman Dave decides to fix up his dad's old Milwaukie "Sabre Saw", metal body, lovely device. Dave lovingly takes it apart, decides to update it a bit with a new power cord, but decides to use a grounded one, after all, it's the responsible thing to do he says to himself, he attaches the ground to the metal body, the idea being if the hot should come in contact with the body it immediately shorts to ground tripping the breaker, good idea. In theory. But then some jagoff goes and installs a bootleg ground, Handyman Dave finishes his repair, takes the tool over to the outlet with the bootleg ground, plugs it in. Unknown to Handyman Dave, he has now connected the body of that saw to the neutral wire of the circuit, neutral and hot are sitting there waiting to make contact, Dave pulls the trigger, fast forward an hour or two and Dave is researching the idea of double insulation and wonders what it will cost to have an electrician rewire his house correctly... This about right?

@okaro6595

2 жыл бұрын

@@BestLittleStudio They are not inherently dangerous. It was the standard way of grounding in many countries. Sure one should not do things that are against the local code. The main problem is interference it can cause because of stray currents that can go through data lines. The most important safety issue is that some people do it incorrectly and create a reverse bootleg ground.

@BestLittleStudio

2 жыл бұрын

@@okaro6595 What data lines?

Thank you this was very easy to understand what’s going on inside old homes wiring. I do not have a ground and I think I’m thinking about upgrading the 100 amp panel box to a 200 amp and thought I would have to rewire the whole house to include a ground to all outlets. What is the best way for me to find what I would need to do without getting taken for a ride. 😊

@AskTheElectrician

10 ай бұрын

Glad it helped you. Be sure to have smoke detectors and AFCI protection as well as GFCI outlets in the required areas.

Great video, Thanks for making it. But if there are multiple outlets on one breaker only the one closest to thje panel should get the GFCI outlet?

@AskTheElectrician

2 жыл бұрын

Yes - Ground Fault protection is provided for all the outlets and other devices on the same circuit when a GFCI Outlet is installed in the first position on the circuit, and wired correctly with the proper Line and Load connections. The same is true for installing a GFCI circuit breaker, all of the circuit is protected for ground fault. Also note that only one type of GFCI protection is necessary for each circuit.

I have question which just recently I was going to replace a old 2 prong outlet with a GFCI. But I stop cause what I have is 2 black wire (I wasn’t able to check for which is hot) and one Neutral white faded looking wire. No ground wire. My question is how do you work with something like this? Much thanks for your videos. Very educational and understanding.

@AskTheElectrician

2 жыл бұрын

We typically identify the wiring by testing using either a non-contact voltage tester, or if necessary we use a voltage tester and an external wire that is attached to a known ground source, such s a water facet or water pipe. Once the wiring has been identified then we can make the proper connections.

Thanks, I just did this on an old basement 2-wire outlet. It cleared up what "no equipment ground" means, it just means no protection for sensitive equipment, people are still protected. But as I understandit, BX or metallic cable with no green ground wire does provide grounding through the armored cable itself back to the panel. When you replace a regular 2 prong outlet with a 3 prong, contact with the outlet box does provide a ground, I don't really understand why the same principle does not provide sufficient grounding for a GFCI.

@AskTheElectrician

2 жыл бұрын

There are several different types of flex conduit and fittings. Some are approved as a means of grounding when installed properly and by using the correct approved fittings and methods as specified by the NEC Code. if in doubt, then install a separate ground wire and use the appropriate boxes, fittings and methods as approved by the NEC Code with has been adopted in your specific area.

So far, this is the clearest video explanation I have watched, so THANKS! I'm trying to install a GFCI outlet in a bathroom. The outlet shares a box with a dimmer switch. The wiring is romex circa late 1960s or early 1970s. Is there any reason why I should or could not replace the old outlet with a GFCI?

@AskTheElectrician

Жыл бұрын

No - a GFCI outlet may be installed no matter how old the wiring is as long as the existing outlet wiring is in working condition and the wires can be identified.

@riptaylorswig4653

Жыл бұрын

@@AskTheElectrician Thank you for sharing your knowledge! I truly appreciate it.

I've seen a lot of these ground/neutral jumpers....and many corresponding panels do not have both bus bars bonded. Seen several 220 outlets jumped too especially dryers...but the neutral bus bars were bonded in the panel.

@AskTheElectrician

Жыл бұрын

Yes - it is unfortunate that there have been a lot of installations of electrical panels and devices that are not correct. One of our goals is to teach others how these things should be done right.

Very helpful video, thank you!! I installed a two GFCIs on a circuit in my older home. One tests fine with a three prong tester but another tests as "no ground". Could that be expected?

@AskTheElectrician

2 жыл бұрын

Yes because this method does dot include a ground wire.

@julianjones3976

2 жыл бұрын

That one needs the sticker.

This video is wonderful. Thank you. Question: I have an older 50s home, plaster/lath, with small electrical boxes. I dont think the normal gfci will fit in them. Is it possible to find smaller gfci outlets that might fit. My wires are cloth covered like your video. I dont want to kostlevthem too much. They are delicate and unravel easily. Can i find and use a small AFC outlet? Would that work as a replacement for ungrounded 2 prong outlets?

@AskTheElectrician

Жыл бұрын

Thank you for watching. Take care when installing a GFCI outlet in a smaller outlet box.

I'm a DIYer and am installing circuits in the basement of my 1955 house. I opened the box of an existing branch to a GFCI which looks to have been installed within the last 10 years or so. There was no ground wire and completely accessible old NM cable, so it must have been a quick fix to replaced an existing outlet. But to my shock (no pun intended) on the GFCI the neutral was jumpered to the ground and to the metal box. And I'm sure this was done by an electrician.

@AskTheElectrician

Жыл бұрын

Jumper wires on an outlet from the ground screw to the neutral connection point on the same outlet should be removed.

Great video. I’ve been replacing all of my 2 prong outlets to grounded outlets. The previous owner did not install any of the ground wires or change out the two prong. Most of my newly replaced outlets now show as grounded. However, some of the outlets are showing as no ground even with the ground wire attached. Is this because the ground wire is not actually grounded?

@AskTheElectrician

Жыл бұрын

It could be - and the only way to know for sure would be to check to see if the ground wires are spliced together at each outlet box, and if the ground wire is properly connected at the panel.

Need to have shown the back of the outlet before install when you explained where you put the wires. Great video

@AskTheElectrician

2 жыл бұрын

Thanks, and keep in mind that you can see more at the website: ask-the-electrician.com See you there!

Thanks for the video.

@AskTheElectrician

Жыл бұрын

You are welcome!

I find your videos very educational, thank you. My daughter recently purchase an older home in Sacramento, California with outlets that are not ground, in fact there is no ground. Can I run a ground wire from the panel outside, under the house through the crawl space to every outlet in the house? . Thank you.

@AskTheElectrician

2 жыл бұрын

Thank you Alvaro, I'm glad you find my videos helpful! Yes - a ground wire may be installed from the main panel to various outlets of a circuit. Be sure the ground system at the main panel has been installed properly as well.

@opel1954

2 жыл бұрын

@@AskTheElectrician i am impressed, not only that you answered my question but you went through and answered every question for this video. Thank you so much.

Hey, in your bathroom you got two pairs of wires. Most likely one of them is a line, another a load. You can easily check which is which and use GFCI to protect a load. Instead you connected them together. Which means that any short-circuit on the load outlets would go to the breakers, rather than being caught by GFCI itself.

@AskTheElectrician

7 күн бұрын

Yes, that is One example of how an outlet circuit may be wired and have GFCI protection for one specific outlet.

Great video, I've a similar situation but I didnt know until im selling the house. I've bought a tester and it seems like some of my outlets showing no ground wire, in the same room I have mix of two one showing correct wiring and one showing no ground wire. Now in my case do I chnage them all to 2 pronged including the ones that are showing it's correct or only change the ones that are showing no ground?

@AskTheElectrician

2 жыл бұрын

If a ground wire is not part of the circuit wiring, or a ground wire is not attached to the outlet box, then a non-grounded two prong outlet should be installed.

Good clear video. If I find the metal box that houses the outlet shows a ground via the BX conduit and I hook it up box to GFI ground screw , is it still necessary to label the plate?

@AskTheElectrician

Жыл бұрын

A label is not necessary if there is a ground wire or properly bonded ground path that is present.

Thank you Ask-The-Electrician!~ OUTSTANDING VIDEOS, Learning a bunch!~ I have a few questions if I may... 1)What kind of analog device are you using to trip the GFCI? That's Not a multimeter right? 2)What if there is No sink or anything that is grounded, how then can you test out your GFCI to trip? 3)I'm remodeling an old small house with no ground, each of the outlets only has the hot and neutral wires through the house. Does this mean that each of these outlets are run on there own circuit? 4) The bedroom doesn't need GFCI correct? If so would it be okay to just replace the 2 prong outlets with normal 3 prong outlets, not GFCI's? 5) I have one of those KLEIN RT210 GFCI OUTLET TESTER PLUGS to trip the GFCI, and it's Not tripping any of these GFCI outlets I recently installed, though it does say on the back of it FOR 3 WIRE OUTLET ONLY. It does trip the GFCI's at my house that has ground wires just fine I should add. Thank you so much for all your time and awesome videos!!!!~

@AskTheElectrician

2 жыл бұрын

Great questions Joseph. The 3-wire GFCI tester you have only works where there is a ground wire as part of the circuit. A ground source must be provided for testing the GFCI outlet, so I typically locate a ground source such as a cold water metal pipe and create a temporary test cable, and then I test using an analog tester, and test from the ground wire to the power side of the outlet and this will trip the GFCI outlet. Keep in mind that there are Several of these topics covered at ask-the-electrician.com. See you there!

@josephrobletto2898

2 жыл бұрын

@@AskTheElectrician HEY, Thank you Very Much. I'm checking out your website now, and i'll watch all your videos and keep learning!~ I watched this video a few times already and keep picking up new things. When you say test cable, do you mean like a long ground wire attached to the metal pipe and ran along to the outlet in question to trip test?

Hello, very nice video. I have an older home built in 1955. Most of the receptacles were two prong with no grounds however some are 3 prong with no ground. I'm not sure why some of the wiring has a ground wire on it and some doesn't. Looks to be older wire similar to what's in this video. There are also outlets in the house that were converted from one gang to two gang with the 3 prong outlets and no ground. There are outlets that were also added to existing circuits via a metal junction box but the box isn't grounded. I figure the easiest way to fix the problem would be to look in the panel and trace the wiring and see which circuits are grounded and which ones aren't. Can i put a GFCI breaker in the panel and will that protect everything in that circuit that isn't grounded? Even if it's a circuit that was tapped with a metal junction box? I think a GFCI breaker would be cheaper in the long run than individual GFCI receptacles. Will a GFCI breaker trip on a circuit that shorts with no ground?

@AskTheElectrician

Жыл бұрын

Thanks for the complement - Yes, a GFCI circuit breaker will protect the whole circuit and trip off if a ground fault is detected.

Just asking, would running a ground wire to the back of the metal box to the ground-wire area on the GFI have any benefit? Probably not as the metal box is just nailed to a wooded stud. I have all two wire wiring in my 1955 built home and need to install a GFCI with a switch/outlet combo. The current switch controls the bathroom light over the vanity mirror and I want a socket under the switch to plug in a shaver etc.

@AskTheElectrician

2 жыл бұрын

If a ground wire is installed properly then it would be best for the ground wire to be installed into the box where it may be bonded and connected to any electrical device which is inside the box.

At 9:55 - how did you test the ground wire to see whether it is an actual ground? Also, when adding the GFCI outlets, should there only be one per circuit from the main panel? Thx,

Excellent video! May I ask if rather than a ground fault outlet in the branch circuit, is it ok to assume someone could install a GFI(?) Breaker and that would cover the entire circuit? It's a bit more $$ but it seems quick and easy. Your thoughts?

@AskTheElectrician

2 жыл бұрын

Yes, absolutely - a GFCI Circuit Breaker is definitely an option to protect the entire circuit.

@brandonknight7240

Жыл бұрын

@@AskTheElectrician what about just putting a gfci plug upstream on the branch

Never would I have thought to jumper a wire from the neutral to the ground. That even sounds like a way to gets someone killed.

@AskTheElectrician

3 жыл бұрын

Your right Darrius - installing a jumper wire from the ground to the neutral on a receptacle outlet is definitely not the way to do it, and it has hazardous potentials.

@jolyonwelsh9834

2 жыл бұрын

@@AskTheElectrician That's known as a bootleg ground.

@okaro6595

2 жыл бұрын

That is how grounding in many countries have been done earlier. All my grounded outlets are done that way.

@JoshR512

2 жыл бұрын

@@AskTheElectrician Is this the reason why I sometimes get shocked in the shower?

@_Depp122

2 жыл бұрын

@@JoshR512 possibly a wire touching the drain pipe

Enjoyed the video., thanks. If a receptacle has no visible ground wire would it be acceptable to place the voltage tester probe in the hot side and then touch the other probe to the receptacle box to see if that is grounded (seeing current) and then if it is just install a ground wire from the receptacle to the box itself? Thx

@AskTheElectrician

Жыл бұрын

Yes, absolutely - that will definitely work.

We have an older home. Some of the wiring was replaced from the panel and is grounded. Could I run just a ground wire from the attic down to the outlets that were not updated?

@AskTheElectrician

2 жыл бұрын

A ground wire may be added to the outlets as long as the ground wire is connected properly and grounded to the main panel or a sub panel ground terminal.

Great video. Thanks for sharing your knowledge. Im learning

@AskTheElectrician

3 ай бұрын

Glad to help

Do you need to hook a load side up if you are putting a gfci outlet in a bathroom? Especially since i don't necessarily need to to protect outlets downstream. I really just wanna protect against electrocution in the bathroom.

@AskTheElectrician

2 жыл бұрын

If GFCI protection is for only one outlet then the Load connections are not necessary.

Great video! At 8:36 you put them both to the line side. I'm curious as to why you didn't check to see if one of them was a load side?

@AskTheElectrician

8 ай бұрын

The circuit wiring was tested before hand to reveal the power source, which is installed on the Line side as noted.

Thank you sir great video!!!!!

@AskTheElectrician

6 ай бұрын

Very welcome

At 8:24, you’ve placed both sets of wires in the “Line” side of the receptacle. Is there any advantage to doing this as opposed to switching on the breaker and finding the hot wire, then putting that into the “line” holes, then putting the other wires in the “load” holes? Will it cause any issues to place both sets of wires in the “Line” holes?

@AskTheElectrician

2 жыл бұрын

Great Question Jacob! When wiring only to the Line side the GFCI protection will work for the GFCI outlet location only, However if there are additional devices that need to be GFCI protected then the circuit wiring for these devices are attached to the Load terminals, And in this case - Yes, the Line and Load wires will need to be identified, especially the incoming circuit power wires which will be attached to the Line terminals, the remaining wires leading to the other devices requiring GFCI protection are attached to the Load terminals. Also, keep in mind that creating pigtail splices may be used as well depending on the number of wires that are used, and how much space there is inside the outlet box.

@laab9479

Жыл бұрын

@@AskTheElectrician would be good to include that information in the video

MUY BUENO AMIGO THANKS

@AskTheElectrician

2 жыл бұрын

Glad to help you!

Thanks for the video. Discovered that that my GFCI outlets in my bathroom are not actually grounded, even though they aren't labeled. More confusing was the GFCI outlet had a ground wire to it, but it was coming from the newer, downstream wiring that was tapped into the line side of the outlet. The supply was 2 wire, so no real ground. Those jumper wires for ground are insane. Makes me wonder if some of my grounded outlets are actually grounded. If there was a jumper, would it test ok with one of those simple wire outlet testers as being grounded, even though it really isn't? Also, could you just leave the grounded outlet (jumper removed if present, of course) and then label the cover plate as "no equipment ground"?

@AskTheElectrician

2 жыл бұрын

Thanks for your comment Bryan. The Plug-In circuit analyzers give an accurate reading, and they are used by many inspectors and electricians. If a ground wire is not providing a path to ground, or is not working then either a two-wire outlet should be installed, or a GFCI outlet may be installed where required as long as the label is placed showing that the outlet is not grounded. Sounds like a great time to check all of the outlets in your home to be on the safe side.

@matt7iron

Жыл бұрын

@@AskTheElectrician hey bub you ever heard of an ungrounded house using the cable line for a Ground and melting the silver metal device coming in off the pole cable wire, my cable guy told me to get the issue resolved before they hook the cable Ground wire back up, now my microwave and 750-1500 plug in heaters are acting stupid.

@yokotaashi

Жыл бұрын

@@matt7iron The cable line will be carrying the cable signal, which is a small amount of voltage and even the shielding will carry a very small amount of voltage carried over from the cable signal. Neither are grounded and so any voltage overflow from your electrical system will leak all the way to the cable company and cause problems. Conversely, the "false" ground created by grounding to the cable will allow the cable signal to leak into some more sensitive appliances and cause erratic behavior. You should only use metal water or gas pipes as ground and do so as close to the service as possible where they are actually in contact with the ground.

@okaro6595

Жыл бұрын

The jumper wire does actually ground the outlet. It just is not up to the code. That method was in many countries the standard method to ground for decades. There are reasons it is not allowed. I do not think it is allowed anywhere anymore.

This is by far the best video of explaining something I've ever seen especially when it comes to electrical issues. You are clear, well spoken your voice stays at the same level throughout. You got to the point and stayed on topic never once bringing up personal life or the person that did things wrong. Some people would have made a hour long video covering the same subject. Thank you for that. With that being said you wouldn't sleep a wink in my home. It was built in 1954 and dad bought the house in 65 and I was a year old. I've lived here all but 15 yrs of my life. It still has an old 6 circuit w/range fuse panel. I've learned what and what not to do. One example is I know I can't run the microwave and the toaster at the same time or I'll be replacing a fuse. You're video taught me I can make it just a bit more safe though. I didn't know you could use a GFCI outlet without a ground and so yes over the years I've replaced most of the outlets with 3 prong outlets that are not grounded. Changing these out for a GFCI outlet will be the least I can do but it's going to be the first thing I start with. Thank you again

@AskTheElectrician

2 жыл бұрын

Hi LH, and Thank You for your kind comments! When updating an older home start with the basics to bring the home up to code especially with AFCI and GFCI protection and smoke detectors, then upgrade the panel and circuit wiring a you are able. Hope tp see you at my website: ask-the-electrician.com

@LH-kz2nf

2 жыл бұрын

@@AskTheElectrician You're welcome and yes I'm one step ahead with the smoke detectors and I have two fire extinguishers in the house as well. I really believe in fire extinguishers. I have one in my car, one in my daughter's car, one on my bike and one I'm my shop. Those can mean the difference in a small burn spot somewhere and you're whole livelihood being turned into a pile of ashes.

I had to rewire from the circuit box to the new sump pump and put a gfci in and gnd to the circuit box. Now I did also have another line going to that circuit to a kitchen outlet next to the sink. But it is two wire. So I hooked it up to the load side of the gfci. Now do I mark it with a "grounded to gfci" or still mark it for "Not on a equipment gnd"?

@AskTheElectrician

2 жыл бұрын

The kitchen outlet that does not have a ground wire should be marked as Not having an equipment ground. Obviously it would be best if the sump pump was not sharing power with the kitchen outlet. Thank you for serving our country!

Does the one that had two sets of wires then protect the rest of the outlets down the line from there? Is there an easier way to tell which one is first without physically looking at the wiring from the breaker box?

@AskTheElectrician

Жыл бұрын

Yes - when the Line wires have been properly identified, and the GFCI outlet is wired correctly with the Line and Load terminations then the outlets down the line will be protected by the GFCI outlet.

Wow who did the prior wiring? Not quite as bad as finding spliced wires covered only by painters tape that has fallen apart, but pretty bad! That bare wire bootleg ground was especially choice.

@AskTheElectrician

2 жыл бұрын

LOL - Yes - We see all varieties of wiring out there, pretty incredible! That's what keeps us busy!

5:02 so will it read as grounded then even if it's not wired all the way to the main power point? And if so is this why you need to add a No equipment ground sticker ?

@AskTheElectrician

2 жыл бұрын

When a GFCI outlet is wired without a ground wire it will not test as having a ground path. However the GFCI will detect if there is an instance to ground that exceeds a normal condition and will trip off thereby providing ground fault protection. This is why the sticker is required, stating that there is No Equipment Ground.

@foltz-art

2 жыл бұрын

Your so Awesome!! TY for your time your answer was very helpful bless you and have a fabulous day 🙏✌

In the one work box with 4 wires don't you have to use a pigtail?

@AskTheElectrician

2 жыл бұрын

It depends on how the GFCI will be wired. It can be wired to protect only the gfci outlet, or protect all of the circuit from that point out. This is why it is important to understand how the Line and Load features work with a GFCI outlet. See the website for more details. ask-the-electrician.com

If I have no ground and add a gfci outlet and I plug a power strip with surge protector will the surge protector work even if it doesn’t have a ground ? The outlet area I want to have a smart power strip to control tv and a electric fireplace with uses a 3 prong 120v

@AskTheElectrician

Жыл бұрын

Probably not, because the surge protector should require a ground wire connection for full protection.

In my living room I tested an outlet with my fluke meter that reads 121.5. What type of amps and voltage of an outlet should I replace it with ? The old outlet crumbled into peices.

@AskTheElectrician

2 жыл бұрын

Replacement outlets should be the same as the original outlets. If in doubt then the outlet circuit amperage should be identified at the electrical panel which provides the circuit. You can see much more information at ask-the-electrician.com See you there !

Am I correct in assuming that when you replace an ungrounded 2-prong receptacle with a GFCI, and plug a circuit tester into the GFCI, the lights on the tester will still indicate the circuit is ungrounded? I have a tester that has 2 amber lights and 1 red light. With a normal, grounded, properly wired outlet, the 2 amber lights are lit and the red is off. When I plug it into the ungrounded GFCI, only one of the amber lights is lit, which indicates "open ground or neutral wire", which seems expected.

@AskTheElectrician

2 жыл бұрын

If the circuit wiring does not include a ground wire or ground path of any type then installing a GFCI outlet does not magically create a ground wire or ground path However what the GFCI will do is provide ground fault Protection if a Fault is ever detected by the ground fault device. So based upon this, your plug in circuit analyzer is correct to indicate that there is an open ground, because a ground does not exist, as stated in your description. I hope this helps you!

I have 2 wires. A black and white. I know black goes to brass but do I connect each line on each side at the top or one on top of right side and one on bottom of left side (diagonal)?

@AskTheElectrician

11 ай бұрын

When there is only one set of wires, the wiring is attached to the Line side of the GFCI outlet.

I haven't checked your list but, do u have a playlist on conduit bending?

@AskTheElectrician

Жыл бұрын

Not yet but working on several new videos!

At 11:24 how do you get away with not having a ground. My recent inspection pulled up some open ground receptacles in the bedroom. Does that need to be replaced with gfci or just a standard un grounded outlet.

@AskTheElectrician

2 жыл бұрын

That would depend on if the outlet circuit actually has a ground wire or not, and if so then the problem should be investigated and repaired. However if the circuit does not include a ground wire then the ungrounded 2 prong receptacles should be installed.

I circumstances like these; I generally install a GFCI breaker in the panel to protect the entire circuit. I then place the labels on each outlet for no ground and for gfci protected.

@AskTheElectrician

Жыл бұрын

Yes - that works as well, the only draw back is having to go to the panel to reset the breaker if there is a fault at any of the outlets.

@mlpabq1

Жыл бұрын

@Ask-The-Electrician I do it that way because I know there is a good ground at the panel and feel that it may be a little better if the gfci can take full advantage of the the way the device was designed.

@okaro6595

Жыл бұрын

That is better as it protects also if the live wire touches an ungrounded metal box.

If there is no ground wire, but it's a metal box, does it matter whether you connect a ground jumper from the GFCI to the box?

@AskTheElectrician

Жыл бұрын

Connecting a ground wire from the GFCI Outlet to the box would also ensure the box to be protected by ground fault as well, but the main concern is to provide protection at the outlet.

@okaro6595

7 ай бұрын

An ungrounded metal box is dangerous. Whether you connect the wire or not in case of hot wire getting loose it can lead the voltage to the equipment case.

"Attach the two wires to the line side of the GFCI",..I wasn't sure what this meant and didn't see a visual of it. The old two prong (ungrounded) receptacle had the white wire on the left side and the black on the right(as I face it) side. Are you saying that both white and black wire should be attached on the right side of the new GFCI receptacle? I was looking for a visual to confirmed this but couldn't find it. Also, although you mentioned checking the polarity three times, I wasn't sure how you did this. Could you explain... Thanks for the video, Dan

@AskTheElectrician

2 жыл бұрын

Thanks for your Comments. Please Visit ask-the-electrician.com for more detailed information.

I have a situation where 4 ungrounded outlets are in a series. Do I need to put a gfci in every recip box, or just the first one?

@AskTheElectrician

4 ай бұрын

If all of the outlets are on the same circuit, a GFCI outlet may be installed at the first location of the circuit, and f the GFCI is wired with the Line and Load configuration then the GFCI will provide ground fault protection to the other outlets down stream on the same circuit.

What’s your thoughts on just grounding it to the metal box in the wall? I’ve always done that thinking it’s better than nothing I saw you just left it ungrounded.

@AskTheElectrician

2 жыл бұрын

If I can verify that there is a ground wire with the circuit from the panel then attaching the ground wire to the box and to the outlet is the correct method. If a ground wire is attached to a metal box and the circuit from the panel does not include a ground wire then this would be a false ground.

@okaro6595

2 жыл бұрын

You cannot ground it to a box. You should then ground the box. In fact a metal box is a safety hazard. If the live wire gets loose or the insulation breaks and the box gets the mains voltage the current will go through the ground wire to the equipment case and it goodbye. A GFCI does not protect against a fault that happens before it. This, however, happens even without any "grounding to the box" as the receptacle is connected to the box. Do not improvise with the ground.

@okaro6595

Жыл бұрын

You cannot ground to a box that is not grounded. The only way that wire can push electricity is to the equipment case (like if the live wire gets damaged) but the screws used to connect the receptacle does it anyway. I have thought metal boxes meed to be grounded so one should change the box to a plastic one if it is not. That is much safer as you will not get killed if the live wire touches the box. Never improvise with grounding!

If there is no ground wire going from the circuit breaker box should all outlets have GFCI outlets in the case? The outlets have three prong but no ground is present when tested. This video is very informative!

@AskTheElectrician

2 жыл бұрын

If outlets are not grounded from a source then two prong outlets should be installed, and GFCI outlets installed in required areas.

@gstrou86

2 жыл бұрын

@@AskTheElectrician thanks for the reply! I just found out that the electrician installed GFCI outlets at the beginning of each circuit and from what I’m seeing that’s suitable. I do plan to have the house rewired later on so I think this is suitable for now.

@okaro6595

7 ай бұрын

@@gstrou86 That is just why they should be marked. If they have properly been marked "No equipment ground" and "GFCI protected".

Very good video...it got me thinking about how this old house was grounded...does this mean these old houses don't have the copper rod that provides the ground connection in the breaker panel... or the ground rod was installed but bonded to the neutral...so anything in that house, particularly water pipes buried in the ground have the ability to conduct electricity from the hot line to the neutral through the "wrong path". I have seen electrical test on non bonded generators in where the hot cable comes into contact with a metal part of the equipment that you are powering with the genset...you can touch the metal...but you will not be zapped... as there is no path for the electricity to go back to the source. Can you explain?. Thanks.

@AskTheElectrician

Жыл бұрын

The ground system for an older home was typically provided by the rigid metal cold water pipe, or a ground rod, or a combination of methods. However there are several methods for grounding a home panel, some of which are determined by the location and the ability to provide a proper ground system. The specific method of how an older home is grounded can only be determined on site after careful inspections. The ground system for a generator will be determined based upon the type of generator and the installation, such as portable generator vs a permanently installed stand by generator, and of course how the manufacturer specifies how the generator is to be grounded and the method that is to be used. It really comes down to the specific application and the generator that will be used.

@tonypower5625

Жыл бұрын

@@AskTheElectrician Good points. Having a partially grounded house is very bad since your body becomes a path for ☠️... I have used a Genset not bonded for many years..with bad extension cord sometime...the frame of the equipment can get to 120 volts.. you can touch it...but you will not be zapped. It will require that you also touch the neutral...in that case you have completed the path for ☠️☠️☠️ I believe that having the GFCi would not protect you since it will not detect the unbalanced current unless you bond N-G at the genset. Hence...a genset with GFCI needs to be bonded in order for the GFCi to work if not connected to the breaker panel???Thanks.

We have a 100+ year old house and the electrical is a pain. In our breaker panel the Neutral and Ground buss is just one terminal strip, they are not separate. I can not get a GFI breaker or outlet to work on it. Any suggestions.

@AskTheElectrician

2 жыл бұрын

At the main electrical service panel the neutrals and grounds are bonded at the same terminal strip. For the GFI breaker make sure to test it without a load or the circuit wire connected. This may help you see if there is a problem in the wiring of the circuit.

I just bpught a 1948 house. It has cables with two conductors, each cloth wrapped, but both black. All the outlets are 2-prong (no ground) and there are no ground wires in the boxes. There are GFCIs in the kitchen and bathroom, but my outlet tester says "no ground" (of course) and "Hot/Neutral reversed". The outlet tester won't go into the 2-prong outlets because there's no hole for the ground prong. How can I test the wiring to see which conductor is hot and which is neutral? I trying to figure out if the hot & neutral is swapped at the main panel or just at the GFCIs? I have a digital voltmeter.

@AskTheElectrician

Жыл бұрын

In a case like this I use my non-contact volt tester, which is pretty accurate, however other wires in close proximity can interfere and cause a false reading. The most accurate way is to create a grounded test wire which is attached to a known metal water pipe, copper being the best, and then use this test wire. This will only work if the whole house has metal plumbing and if the main water service is metal as well, which is most likely rigid steel or galvanized water pipe.

you connected to the line side of GFCI #2 from the load side of GFCI #1 ??

@AskTheElectrician

Жыл бұрын

For wiring GFCI Outlets with various configurations you may consider the following: ask-the-electrician.com/GFCI-Receptacles.html This will help you - see you there!

In these circumstances where there is a metal box. Would it be of any purpose to install a ground tail (Equip. Grounding Jumper) from the outlet to the metal box?

@AskTheElectrician

2 жыл бұрын

If the metal box has been tested and it is grounded either internally or externally then yes, a pigtail ground wire should be attached and used.

@christophermunoz9276

2 жыл бұрын

@@AskTheElectrician Makes sense... Thank you!

What does the multimeter set to when checking the GFCI for grouding

@AskTheElectrician

8 ай бұрын

A plug in circuit analyzer is very useful for testing for ground, and other circuit conditions.

Hello! Came across your video as I’m trying to diagnose a ticking noise being given off by my guitars amplifier. I’ve plugged it in at other locations and it doesn’t make the noise. Also tested separate amp on same outlet and I’m getting the tick. It’s older home and I’m almost certain there is no ground wire. Pretty sure at some point someone replaced the two prong outlets with three prong ones and called it a day. My plan was to replace the outlet with a GFCI. Would replacing with GFCI ground the outlet as I hope it would, despite no ground wire being present? Thank you, great video

@AskTheElectrician

2 жыл бұрын

Before replacing the outlet you may consider trying to locate the source of the ticking. Keep in mind that a home has two lines of power where each line may serve power to other circuits in the home. You may try unplugging electronic devices in the home, one at a time and see if the ticking goes away, and then possibly plug that device into another outlet on another circuit. Another solution would be to obtain a good quality plug strip with noise suppression and voltage conditioning. I hope this helps you - Happy Picking!

@RussianColluder

2 жыл бұрын

@@AskTheElectrician sure enough, I unplugged this ikea lamp with a dimming switch and the ticking was gone! Free lamp to an amp-less home.

At 8 minutes in where there are two sets of wires coming into the box , could you not use pigtail wires from the common and neutral wires to complete the circuit and protect that one receptacle location ?

@AskTheElectrician

Жыл бұрын

Yes - the wiring method you have described will protect that one outlet. Examples of this and other projects are found on ask-the-electrician.com

I have a 1950 home, in the kitchen is a 3 prong neweroutlet with 2 white wires on 1 side and 2 black wires on other side ,walt to put in gfce outlet, how can it be done?

@AskTheElectrician

6 ай бұрын

Typically the wiring is tested and verified first, and then the GFCI outlet is installed and wired accordingly. More information is found on my website.

What you didn’t mentioned is that even with a gfci installed, your gfci will show “open ground” because no ground wire connects to it.

@AskTheElectrician

Жыл бұрын

Yes - and that is why the sticker has to be placed on this method of installing a GFCI outlet to indicate that the outlet is not grounded. What you are describing will be covered in my video about Testing Outlets - good observation.

@sidpryor6469

Жыл бұрын

I’m getting a “hot/neutral reversed” error, would this mean another issue down line?

I have a rental property that failed inspection with no ground so I put gfi's in so I'm hoping this will pass inspection

@AskTheElectrician

3 жыл бұрын

It should pass inspection because the GFCI Outlets will provide the required ground fault protection in the required areas.

@known2100

2 жыл бұрын

Did it pass? My rental failed inspection twice because of it. Even though I had GCFI outlets installed. If so what kind did you buy any specific brand maybe? I can't think of anything

@toolisbalance

2 жыл бұрын

Did you pass your inspection Thomas?

@mikejohnson9586

2 жыл бұрын

GFCI installed in my house and did not pass. Now, I have to invest in rewiring house. It will cost me 16,000 dollars.

@Sparky-ww5re

Жыл бұрын

@@mikejohnson9586 you must've had a very strict inspector. The NEC does permit an older non grounding receptacle with a grounding receptacle, provided it's protected by a Ground Fault Circuit Interrupter and you label the GFCI outlet "NO EQUIPMENT GROUND " and any newer grounding type receptacles are labeled "GFCI PROTECTED, NO EQUIPMENT GROUND. " 406.4 (D) (2) (b) & 406.4 (D) (2) (c) of the 2020 NEC

At the 2:45 mark, How did you check the polarity of the wires?

@AskTheElectrician

2 жыл бұрын

Great Question! The polarity of the wires is checked using an existing grounded source, which in this case was the metal facet of the sink where I touched one of the tester probe wires to the facet, and the other tester probe wire to each wire of the circuit. When the tester gives me a 120volt reading on one wire I know that the wire is the power conductor. In most cases a non-contact voltage tester may be used as well to detect the power conductor.

My house was built in 1939, and has those cloth wrapped wires. GFCI receptacles are a lot larger then the original receptacle. Any tricks on getting a GFCI into those old style smaller boxes

@AskTheElectrician

2 жыл бұрын

Yes - the original boxes are very small so if the space is too small for the wires and the GFCI Outlet then a surface type electrical box, such as a Wiremold product may be installed by mounting an Extension box on the surface face of the existing box, and the extension box will provide more space for installing the GFCI Outlet. The only other option would be to carefully extract the existing box and replace it with a deeper single gang box, and this is possible, but it is very tricky and one has to be very careful. Also keep in mind that some of the GFCI Outlets are slightly smaller than before, or when comparing to another brand that you are considering which may be larger.

@maxheadroom8857

Жыл бұрын

@@AskTheElectrician I will add this: some of these older homes don't have drywall because it was built before drywall was created. These older homes have plaster instead. I live in a home built in 1955. The original owner built the house himself, using plaster to finish the wall. My folks bought the home in 1961, before my older brother was born, and my sister was a baby. When I was in high school back in 1980, I had taken a class in Electronics and learned about house wiring and NEC Codes. My parents had me replace a double switch box that got rusted and damaged from a roof leak over our kitchen. That double gang box was next to the outside exit from the kitchen, and contained the wires to an outdoor backyard porch light and 1 of the light fixtures in the kitchen. I found it can be messy trying to replace a box, but worth the effort to do it yourself. I even found out that the old double gang box happened to be grounded from behind with a separate 12 gauge bare wire nailed to the box bracket and stud. I managed to carefully remove the box after breaking up the plaster carefully around the box, and route the ground wire into the new double gang box. The new double gang box was an expandable box which I nailed in place to the stud. I used new Romex clamps on the switch wires and routed the ground wire inside the box, grounding the box properly with a grounding machine bolt. At that time, new light switches did not have grounding screws, so I rigged a self grounder to ground the light switches to the box when screwed in. By the way, the wall with the double gang switch box has the kitchen sink on it. Right near the switch on the next stud, I have an old grounded outlet inside a small box as well. That box was also damaged by the roof leak above the kitchen years ago. When we did a plaster repair to the wall decades ago, I saw the ground wire attached to the box bracket nailed to the stud as well. I currently have a GFCI and box ready to replace the old rusty box and the old grounded outlet. The challenge will be repairing the plaster around the box, once the new box and GFCI are in place. My community doesn't require me to put in AFCI/GFCI combinations in my kitchen; just the GFCI for now. I'm not about to install any "childproof" outlets either, even if NEC codes say they're required now, as I don't have children living in my house. There is 1 thing I'm curious about: do you know if NEC code back in 1955 required that light fixtures exposed to the outdoors such as porch lights were required by code to be grounded? I have 2 outdoor porch lights, one on a wall with plumbing on it, and grounded per fixtures on walls with water pipes and the other on a wall with no water pipes and sinks. I have no way of testing to find out if the front porch light is grounded or not. I do know my back yard porch light is grounded because an electrician tapped the fixture box to install an outdoor outlet to power a water softener back in 1964. The walls the front porch light is on have no exposed plumbing fixtures.

I pulled out an old electric outlet, to replace it with a GFCI. I accidentally touched some part of the old outlet while removing it on the metal box, and saw a small spark. (I thought the fuse was out, but maybe I had the wrong fuse out). Now, I am reading 14 volts from hot to neutral, and from hot to the metal box(ground). I've pulled every fuse in the panel, and still see 14 volts! Note, the outlet was working fine before my accident (although the hot/neutral were reversed). What did I do break when that old receptacle sparked? Did I burn/short a wire, or junction? How do I find the problem. I cannot use continuity tests since I have 14 volts present. Help!

@AskTheElectrician

Жыл бұрын

At the main panel the main fuses should be checked to see if one has blown, if so it should be replaced with the same type fuse.

For my living room I'm getting 120 volts on my fluke meter, but how many amps do I get for my outlet ?

@AskTheElectrician

2 жыл бұрын

Amperage is the amount of electrical current that may be used by the outlet, and is specified on the label.

I have this old cloth wiring. How do I know which is the hot wire and which isn't?

@AskTheElectrician

2 жыл бұрын

I use a non contact tester, or extend a wire to a ground source.

Working in an older home; 2 wire with no ground in a bathroom. Trying to add a GFCI with the line in, and then run from the load side to a dimmer switch for the light. I am unable to get the switch to function properly; after setting the GFCI, the light does power on, but no control from the dimmer switch, almost as if I have somehow wired the power to “bypass” the switch completely. At a loss.

@AskTheElectrician

2 жыл бұрын

Make sure the dimmer switch is compatible with the lamps in the light fixture. Also double check the Line and Load wiring to the GFCI outlet.

If you have an ungrounded outlet and a fault occurs in an appliance, will this both energize the appliance and the outlet itself?

@AskTheElectrician

5 ай бұрын

If there is a Ground Fault that is detected with a GFCI outlet then the GFCI will trip off the power to the outlet.

Excellent information 👍👍👍

@AskTheElectrician

3 жыл бұрын

Many many Thanks, Martin!

Thank you brother

@AskTheElectrician

3 ай бұрын

Your Welcome!

how do u check the wire to see which one is hot and netural, without power to the wire, thanks

@AskTheElectrician

2 жыл бұрын

I typically look at the color of the wire insulation, which can also be verified back at the panel in most cases. However when in doubt, or if the circuit is a branch circuit, then tracing the wiring on a branch circuit, and using a continuity tester may be required to ID the wiring.

I always have code enforcement familing me on inspections for GFCI having an open ground but I though they didnt have to have a ground. its not a simple fix they want me to independently and rewire all gfci easier said than done. does current code allow for GFCI to not be grounded?

@AskTheElectrician

Жыл бұрын

Yes the code does allow a GFCI outlet to not be grounded, as stated in this video, the label has to be in place. The Ground Fault protection is still provided through the Ground Fault Outlet internal circuitry.

How depth should I bury my UF wire indoor from wall to kitchen island? Thank you

@AskTheElectrician

Жыл бұрын

UF Type cable is intended to be used for Underground Feeder applications. When is it installed underground it is typically buried 18inches deep.

So even if a tester says "open ground" its grounded?

@AskTheElectrician

2 жыл бұрын

Keep in mind that this method does not magically produce a ground wire that does not already exist. However it dos provide Ground Fault Protection.

Hey guys what if I don't have any ground wire or grounding in the house what do I need to do to ground my room outlet

@AskTheElectrician

Жыл бұрын

The home should be checked to make sure the main electrical service panel is grounded, and if not an approved ground system should be installed. If the circuit wiring inside the home does not include ground wire then this video will help you in the areas where GFCI protection is required. Installing ground wires for the existing circuits, or upgrading the circuit wiring should be considered as well.

Can you use a GFCI switch/outlet combo with this wiring?

@AskTheElectrician

4 ай бұрын

a Combo Switch Outlet will protect the same way, however it will only protect the single outlet.

What is the difference between ground fault and ground path?

@AskTheElectrician

2 жыл бұрын

A Ground Fault is an event that occurs, such as a person getting an electric shock. A Ground Path is a physical device or environmental element that provides a low resistance connection to the earth ground.

You could stil use a gfci for non wet environments it will still provide protection

@AskTheElectrician

25 күн бұрын

Yes