Your videos are the most detailed and reliable. Thank you so much for such useful content.

Everything that I needed to know about the tp5100! Thank you!

Hello Sir. Thank you so much for the very clear explaination. This is way better than TP4056 charging module. 😊

Perfect streaming, love your explaining why and talking speed 🌹

Sir, you have taught me for years in the form of your videos Thank You

@robojax

3 жыл бұрын

Hi Asha, I am glad you found my tutorials helpful.

Thank you for this very detailed review, sir! Learned quite some new concepts from here.

@robojax

3 жыл бұрын

My pleasure!

Mr. Shamshiri, I truly enjoy your videos with the thought process, planning and the abundance of information you provide. After all, it takes work to video, edit and review your work and I find it flawless. Even corrections. I have an entire line of cordless tools for sears back when I could work. I am prepared to disassemble and pass judgment on each cell. How or what math is used to determine the current to charge cells the show promise? A dead battery is dead, but unless it has a dead short internally, it has a chance to live again. I take the numbers stamped on the shrink wrap and research to find voltage but aH info. I can not order every single cell ti fix each battery pack as it would be cost prohibiting for my wallet. But having 9 perfectly good tools sitting on the shelf does me no good. Automotive ASE Master Tech since 1978-Retired I have already used your excellent product testing videos to pick two modules to purchase. Thank you again!

@robojax

3 жыл бұрын

Mr. Kay, I am pleased that you like my tutorials. Yes indeed for each video there is lots of efforts. Very few such as yourself know this. first of all battery capacity and charge parameters are the most tricky part of working with them. The charge current is determined by the manufacturer of the battery. charging above the rated current will reduce the battery life. So you have to find the datasheet. for example for the Panasonic battery shown in video here is the datasheet www.batteryspace.com/prod-specs/NCR18650B.pdf and it says the the standard charge should be about 16550mA. or lower. I have spoken about battery protection in this video kzread.info/dash/bejne/ZZiro5p6aLnYoqg.html so generally for less than 10Ah batteries, always go 0.5 of capacity or lower to protect it.

@deankay4434

3 жыл бұрын

@@robojax Thank you again so much for the reply. I will identify and look for data sheet & their recommendations. I have never posted a video on youtube, but have a great understanding on lighting, camera angle or position, just a lot. This is basics, but you go a long way to provide information at least I find extraordinary and as accurate. You have my total respect in your total presentation. My last job had me holding automotive technical 4 hr. seminars for 20 to over 100 each night during a whole week in a different town or city. So the old “Dog & Pony” show. Taking photos, screen captured from a lab scope or scan-tool to use these in the power point was not in the job description. But the presentation had diagnostic holes in it, large enough to drive a truck thru. Advanced Charging systems, Serial Data (6 types in GM vehicles), etc. Magneto-Reological-Fluid used in struts in place of traditional oil and valving found in a common shock. Called “Active Ride Control” and other terms, but basically tiny metal particles suspended in oil. When a magnetic field is applied at a variable rate, change at 2mS changes from a thin less viscous oil to a rigid hard non-fluid material. This was started in suspension in 2004 Corvette. Acura used it in rubber motor mounts. When ran on a dynamometer, the vibration generated on up shifts, down shifts, all parameters, they mapped the dial-in amperage required was downloaded into a EEPROM and allowed later to change the ride feel, smooth, sport, racing anything they wanted. So, electronics coupled with mechanical applications is amazing. So a basic understanding was needed to pass along to guys/gals who may have to work around these or replace them, then recalibrate. Total electric vehicles make no noise (Very Little) but I joked two decades ago that waterproof speakers could be added to allow the driver to turn a knob to make it sound like a hot rod V8, 10 cylinder Viper or a loud 4 cylinder w/turbo. No, people on phones walk into streets and get hurt or killed. Laws maybe passed requiring them to make noise. The possibilities are endless. Just sharing as the guy who makes a simple kit can patent this (Installed by customer on older vehicles) but make millions, if a manufacture buys the patent or the rights with a percentage for license for each one sold/used. It’s a gold rush, but few would think of it or pursue it. I have ideas. Ok, enough. Blessing to you & loved ones! Thank you again. I could be reached as I am just working on my own old truck for me. A project to keep both hands & mind working at 62. Stay safe!

@robojax

3 жыл бұрын

Hello, Mr. Kay, You are welcome and I am glad you like my tutorials. You've got so much experience. wow. I've read your comments and enjoy them. To make electric cars noise, many states have considered/did pass legislation to to make it mandatory to have noise added. I am not sure if it has been implement or not. I have an Arduino course which starts from absolute beginners and up bit.ly/rj-udemy God bless you too and your family. you too stay safe.

Your video is very instructive, thanks for the information.

Thank you for reviewing this module, and also great review! Just a note, you can not apply your time to charge calculation, since the current will lower once cell reaches near 4.2volts, the real time might be something like 3 hours depending on the type of cell.

@robojax

3 жыл бұрын

you are welcome. Agreed with your statement.

WOW what a mount of details soooooooooooooo useful . I would thanks to you sir and show my all respect to you . this video what i am looking for . excellent video

Excellent explanation for a novice like me. Subscribed.

Hello Sir. Thank you so much for the very clear explaination. This is way better than TP4056 charging module.

Hello bro Thank you so much for the very clear explaination

Amazing review, thank you!

@robojax

3 жыл бұрын

Glad it was helpful!

Super Explanation sir.....thank you very much....

Thank you!

Very clear Thanks Sir LOVE from Pakistan

Comprehensive, excellent video!

@robojax

3 жыл бұрын

Here is my other channel which on Solar, charger and batteries kzread.info/dron/vT_lj6oLAqq60s7VUcTczQ.html

Thank you Ahmad, nice video, great details

@robojax

3 жыл бұрын

My pleasure

Thank you .very useful

Thanks for sharing knowledge!

@robojax

3 жыл бұрын

My pleasure!.

Canadian electronic channel noice!

excellent explaination 🌹🌹🌹🌹🌹

Great Video !😊👍

@robojax

3 жыл бұрын

Thanks for the visit

Thank you good 👍👍👍

Well explained.

Rất tuyệt vời, cám ơn bạn đã có 1 video hay

@robojax

3 жыл бұрын

Tôi vui bạn thích nó . Xin đừng quên đăng ký. nó sẽ giúp kênh của tôi phát triển.

Thanks for share~~

i like your channel very much :)

@robojax

3 жыл бұрын

Glad you enjoy it!

Cảm ơn bạn! Clip rất ý nghĩa

Good morning Robojax, I am very grateful for your video, I have learned a lot, I need you please to make a video of a W5500, Ethernet module.

@robojax

3 жыл бұрын

Hi Recardo. I am pleased that you like the video. I have it on my "to do" list. When timer permits, I will make video. of that.

عالی بود. موفق باشی داداش

@robojax

Жыл бұрын

تشکر‌. . خرسندم که خوشتان آمد . سلامت باشی

@robojax

Жыл бұрын

سلام علیکم. مجرا (کانال) فارسی علم و فن را راه اندازی کردم: لطفا به دوستان تان خبردهید و حمایتم کنید. www.youtube.com/@ilmofan

Tesekkürler

@robojax

3 жыл бұрын

Beğenmene sevindim.

12:10 Yeah !! thank you for pointing out the capacity unit which is Ampere x hour and not Ampere/hour. It is good to put the unit in the calculation so we know what unit we got in the result. It may be a details, but it piss me out frequently in other video or other internet source when they spread tainted information.

Great video at the start of video you said different model for charging and balance what model where you talking about

Good review man. But which resistor need to changed to adjust the charging current?

Thanks

@robojax

3 жыл бұрын

You are welcome.

Thank you for the information and review - highly appreciate it - one quick question regarding the TP5100 - How do I utilise the under-voltage protection? I do not see an output - is this module only for charging. The batteries I'm using are un-protected.

I am thankful to have your demonstration over TP5100, Really amazing. One quick question, can i connect additional LEDs over the pads that you were shown. Please suggest.

@robojax

3 жыл бұрын

You are welcome. I am sorry I did not understand. Which LED?

@svem1972

3 жыл бұрын

@@robojax The leds that are connected to pin 15 and 14 pin to tp5100 and 1k resistor that comes from input. near by there were 3 pads, and in your demonstration were shown using tester of touch each pad and led indicates. in that position can i give led connect.

@robojax

3 жыл бұрын

The LEDs are turned on using the chip. You can connect additional LED for sure. If you connect it in parallel, it will turn on but might be dimmer. As I have shown the diagram, connect them to pier via 330 to 1k ohm resistor

CS is "Chip Select" (as in "on"), not "Charge Select". Thanks for the video.

@robojax

3 жыл бұрын

You may right. Thanks

I want to replace a 9 volt battery with a 18650 pack. I'm wondering if I should use 2-3 18650 batteries in series? Should I use a single 18650 and a boost board? Or maybe two parallel 18650 batteries and a boost board for more capacity? I want to leave the battery in circuit with charger connected. Thus, I want a circuit that safely protects from over-charge or under-discharge. Do you recommend parallel charging 18650's? Thanks for any help.

if i connect 5v at the input can i still charge 2 batteries or just one? if not can you recommend other charging boards that can do this?

As i remember data sheet shows polarity protection available but in prctical it is not. Did u test it for under voltage protection and over voltage protection?im have doubt

May i ask something, can we direct connect the middle of the series battery connection into set ,?

Hello! I've got a question. As soon as the battery is fully charged, the red LED will turn off the the blue one one turn on instead, right? Also, with this circuit I have to disconnect the battery at the time the charging process finishes (for safety), or is it prepared not to burn the battery? Thank you so much and your videos are super useful for us beginners!

@senterterapibioglass3677

3 жыл бұрын

When the battery is fully charged, the RED will off and the BLUE RED will on. YES. No need to remove the battery from battery holder, except you want to use it with different device.

عالی بود، مخصوصا زبان زیرنویس فارسی❤

Toujours les meilleurs tuto Robojax , Vraiment complet et les tests sont vraiment parlant sur la qualité des modules. J'ai ce module , Mais est ce que l'on peut Charger les 18650 en même temps que elles sont connectées à un Arduino ou autre chose ? J'ose pas essayer

@robojax

3 жыл бұрын

Bonjour, je suis ravie que mes tutos vous aient plu. vous pouvez connecter votre batterie pendant qu'elle est chargée UNIQUEMENT si vous la connectez à la broche VIN d'arduino ou à la broche de l'adaptateur d'entrée. Jusqu'à 12V n'endommagera pas la carte Arduino.

@lllAstridddlll

3 жыл бұрын

@@robojax Merci C'est bien noté, 12v maxi ,Oui je suis abonnée depuis un bon moment à ta chaine et je la regarde toujours avant d'acheter des modules , car tes tests sont complets et clair , en plus il y a les traductions , ça facilite la compréhension, pour moi tu reste toujours la meilleure chaine pour tous les modules chinois, longue vie à ta chaine.

@robojax

3 жыл бұрын

Merci beaucoup et restez en sécurité. J'apprécie de partager ma chaîne sur votre facebook et vos amis.

Can I use two chips in parallel to get max current upto 3Amp ? Awesome video

@robojax

3 жыл бұрын

Thanks. Yes you can if you set both voltage at exact values. Slight difference of voltage causes the current to flow from one to the other and waste the energy.

Great! Don't you need over charge protection and over discharge protection for each battery?

@robojax

3 жыл бұрын

I don’t remember but I know for sure if this module has such features I would have explained it. So watch fully and the answer.

Thank you so much, but you have forget to show the efficiency on charging 1s battery.

@robojax

3 жыл бұрын

you are welcome. not forgotten. I've shown it or mentioned the current.

Thanks for making this informative video. If I just wanted more capacity, more amp/hrs, could I wire the batteries in parallel and use this charger please?

@robojax

Ай бұрын

you are welcome. Yes you can. I have moved most of battery and engergy relaerd videos to another channel called WattHour here www.youtube.com/@watthour

@acestudioscouk-Ace-G0ACE

Ай бұрын

@@robojax Thanks, I'll take a look. 👍

If I connect 5 or more lethium iron battery the module heats very quickly is there any solution is there,I also used heat sink but also it heats very quickly.

Mr. Ahmed shamshiri from canada, valuable video from you. Please make videos for 3s bms board and tp4056 module. And there’s a new tp5100 which is charger and boost up volt in one module. How work and how wiring. Greetings from Saudi Arabia. Thanks.

@robojax

3 жыл бұрын

Assalamu alaikum Mr. "Allahu Akbar", I am glad you found my videos helpful. TP4056 is for 1S see datasheet here dlnmh9ip6v2uc.cloudfront.net/datasheets/Prototyping/TP4056.pdf See my other videos on chargers kzread.infosearch?query=charger

@__-hh3gt

3 жыл бұрын

@@robojax Thank you for your quick reply and kind cooperation. I just bought a festnight bench power supply. Please make a video for the usage of bench power supply. Greetings from madina, Saudi Arabia.

@__-hh3gt

3 жыл бұрын

@@robojax I very happy with your saying “allahu akbar” that’s mean you are muslim same me. Good luck.

Thanks do we still need BMS along with 18650 cell to charge safely or this board comes along with all sort of battery protection ?

@robojax

10 ай бұрын

as I saw interest in Lithium batteries, I purcahsed boxes but don't where to use them expect to make video. Why and where do peopel use batteries so I learn and use. Then perhaps I know I would make better videos. until now I pent like over $2000 for batteries and they are on the floor.

if input 5v 1amp than output8.4v what is amper? i want to run modem 9v 100ampare tanda?

hi, thanks for the explanation. Can this charge and discharge the batteries at the same time ? in tp4056, we could use B+/B- to connect to batteries and out+/out- to a consuming device

@robojax

Жыл бұрын

Yea it can because the path is different for charge and usage. I don’t have it in hand to test though.

Hi there I make this circuit use 2 battery's but only blue light blow of charging period time on the module so what solution you suggest please reply this most commen problem Thank you so much

selamTP5100 aldım 2S bms aldım 2S bms yi kulanmasm olurmu TP5100 pilleri korurmu

can it charge and discharge at the same time like when I use it as a power source for a speaker with batteries and usb charger connected will the speakers work while charging? can I use two cells in parallel ?

@robojax

Жыл бұрын

Yes you can

where did you get the thermal imaging camera that you connect to your phone?

@robojax

3 жыл бұрын

The link to the Thermal camera is in the description of the video.

Hey @Robojax That was well explained. Thanks! I have a question. I am using 8.4V setup, both the 3.7V batteries are connected in series And when I charged it for about half an hour, the batteries got heated up. I stopped charging to avoid any further damage. I disconnected batteries and checked individual voltages. One was at 4.14V and the other was at 3V. Am I doing something wrong here? Is it okay to charge when batteries are at diff voltages?

@robojax

3 жыл бұрын

Hi you are welcome. , you did not mention the capacity of the battery. I mentioned in the video that you have to limit the current. The current causes the battery to get hot and life of battery is reduced significantly. I have given example about capacity. please watch it gain.

@ezioauditore3252

2 жыл бұрын

Probably use a 2s BMS as well along with this TP5100 module. TP5100 should supply power to 2s BMS. 2s BMS should supply balanced power to 2*18650 batteries.

@paulvincentangcon2659

Жыл бұрын

@@robojax Hello, As the video says, The Negative and Positive wires are connected to the S1 Battery, then You connect the wire from S1(+) to the S2(-). My Question is, What do I do with the S2(+)? Should I connect the S2(+)where the S1(+) is connected or do I leave it there?

12:51 can I use it like this without a balance board between the batteries? If I use LiPo or Li-ion cells?

@robojax

3 жыл бұрын

You can but with this module, your battery will be damaged. you need constant current controller which this TP5100 has .

Mr. Shamshiri, thanks you for the clear explanation. Suscribed. I would like to ask a question: is it possible to charge a Li-ion battery pack 1s2p (3,6V 5400 mAh) with this module? Thanks!

@robojax

Жыл бұрын

Hello, yes you do as many parallel so you like. But remember the amount of current this module supplies stays the same so the time will take longer. inf your case it will take twice as long to charge. if you use 1s3P, then the 2A from this charger will be divided to 3 and it will take 3 times as long to charge them.

@federicofallica5762

Жыл бұрын

@@robojax Thanks very much!

Hello Ahmad! Firsty many thanks for your video. So helpful. My question is that can we use TP5100 and 2S BMS (which is connect to output) together or TP5100 is enough for charge-decharge for 2s lion batteries. Another question is can I use USB Type-C female connector to input (for 9V)

@robojax

3 жыл бұрын

Hello, I believe I have explained it and demonstrated 1S and 2S charging. for one sell you can connect it to 5V but for 2S you need higher than 8.4V at input. But I did not understand why you would connect this module with another module. two battery is 2S already which this module can charge.

@ThePremonitor

3 жыл бұрын

@@robojax Hello again Ahmad. Firstly many thanks for your answer. My electronic intelligence is poor. I thought that I need bms module for balanced charging between two bateries. You mean we don't need extra module, TP5100 can do that even there is no wire between two cells, right?

@panagiotissavvidis8271

2 жыл бұрын

I have the same question as you clearly note in this video this module won't balance the 2s batteries. I came to your video for TP5100 from a HX-2S-JH20 thread that is better to use the the former for a correct charge. As another member here asks the same, would the output of TP5100 should accommodate a HX-2S-JH20 for balancing?

@frankfernandes648

2 жыл бұрын

buddy u are right...u need a 2S BMS to protect and charge batteries indivually...

Can 5-18 volt applied directly to th input?

Hi Great Video, Have you reviewed hx-2s-d01 module ?

@robojax

2 жыл бұрын

Hi, I have over 450 videos and almost forgot what I have done. Here is how to find Specific KZread Video in a channel bit.ly/findKZreadVideo

@robojax

2 жыл бұрын

just saw it on Google and NO. I have not done. it.

@robojax

2 жыл бұрын

I just searched the circuit for the module you mentioned and it is exactly the same protection as shown in this video so watch this to learn how battery proteciton works kzread.info/dash/bejne/fp-TwdqNqK_SiZM.html

@1:45 can you suggest the balancer or a board that does both?

@robojax

3 жыл бұрын

chargers are here kzread.infosearch?query=charger and balancer is here kzread.infosearch?query=balancer

Thanks for the detailed explanation. I have a question. I am using the module to charge 2S battery. When battery reaches to 8.36 - 8.37V, the RED and BLUE LEDs are flashing alternately. What does this mean? Is there a problem?

@robojax

Жыл бұрын

Hi, I just added the PDF datasheet on the resources page. in page 10 in the table is says: no battery is connected or the output capacitor 10μF (issue or missing)

Hello sir nice video Can i use the 5v input votage to charge S2 7.4v battery ? Or can i use the votage booster to charge it ? 5v to 12v then charge 7.4v battery

@rchrdson21

Жыл бұрын

I need to know also..

Hello! What would happen if I use a 12v solar panel instead of a 12v dc outlet? Would it be efficient?? Thanks!

@robojax

3 жыл бұрын

Voltage is voltage. does not mater where it comes from.

What is the input voltage and its source?

so in the 2s mode its just bulk charging the batterys in series?

@robojax

Жыл бұрын

yes but with all protections or charge and voltage.

Bro!, Please help me!. I'm changing the battery system of my bt speaker. My amplifier is xy-p15w 8-24v dc. Which one is better? 4 18650 in parallel and use IP2312 then use converter 3.7v to 12v or 2s2p 18650 and use TP5100 then use converter 8.4v-12v? I want fast charging using 33 watts fast charger of poco x3 nfc

can you explain about "power-on" feature please?

@robojax

3 жыл бұрын

What do you mean? There should nothing left without explaining for this module

Will the amount of current source affect the output current? Say if my power source is 5v 1A, will the output still be 8.4v 1.9A?

@robojax

3 жыл бұрын

Power =P, Voltage =V and Current =I, So for input P=IV=5(1)=5W, output P=8.4(1.9)=15.96W, absolutely not possible. you have $5 but you want to buy $15.9. Power never increases and not even the same. we always have losses. about 10% to 15% is lost at output Only voltage and current is changed.

Limiting the charging current like in tp4056 R3 resistor. Is it possible in tp5100?

@robojax

2 ай бұрын

Yea you can. See datasheet the way I explained it voltiq.ru/datasheets/TP5100-datashhet.pdf?darkschemeovr=1

Hello! Can I use bms with my 2s batt with this lithium charger?

@robojax

3 жыл бұрын

no. if you watch it, I've explained that it separate wires for charge and separate wires for load.

Thanks for sharing, when I charge 2 batteries in parallel ( one cell mode) I only get 4.1V on each battery and the LED changes to blue any advice. THANKS

@robojax

2 жыл бұрын

That is correct. When you connect in parallel, the voltage does not increase. Only charge time increases

@mohammedshalash7842

2 жыл бұрын

@@robojax I was expecting 4.2V on each battery Thanks

Can i use this to charge using 5v powersupply to series 3.7v battery?

@robojax

3 жыл бұрын

sorry I did not understand. may be you did not watch the video fully. did you? for one cell it needs 5V input. for 2S it needs at least 8.4V at input.

Can use 12V or 9V ?

Is Bms not needed to charge my 18650 batteries with Tp5100? Or Bms still needed to charge safely all my batteries? Thank you and hopefully to get an answer from you.

@robojax

Жыл бұрын

this is BMS. you BMS h as protection. But can't control the current as to how much should go to your battery. this module can allow up to 2A. but if you connect a small battery with capacity of for example 500mAh and charge it with 2A, it will get damaged. So you need to connect a power source to this with controlled current (ampere). that's why connected your charger that controls the maximum current. An example of a charger would be a step down converter with constant Voltage (CV) and constant Current (CC). So you set the output of that to 8.4V (for charging two cells) and set the current to 200mA or whatever value your battery require. if allow more charge current that your batter require, battery get damaged. So find out about your battery's charge current. Good luck

@robojax

Жыл бұрын

Learn about battery protection from this video of mine in another channel which is all about power, charge and battery kzread.info/dash/bejne/fp-TwdqNqK_SiZM.html

What is max input current for a safe run

@robojax

Жыл бұрын

I belive I have answerd such basic questions in the video. Don't remember it .

Can I use transformer of voltage input?

@robojax

Жыл бұрын

No. It needs DC voltage.

what is charging time been 3 hrs still red led its charging

Test tp 4056 charging module also

@robojax

3 жыл бұрын

I will see if I can get it. thanks.

how about the over discharge protection of the battery?

@robojax

2 жыл бұрын

I believe I mentioned "Undervoltage protection" and it is mentioned as over discharge protection . please check the datasheet in the resources page robojax.com/L/?id=265

@jonalddejesus6726

2 жыл бұрын

@@robojax can i use this tp5100 with a 1s bms for added protection?

would you please revieu an inveter below 1000watt

@robojax

3 жыл бұрын

inverters are expensive and I can't afford to buy them. If I receive them for free, I will do it.

Sir for 2s battery charge can we use 9v as the input voltage of tp5100 PLZ REPLY 🙏🙏

@robojax

2 жыл бұрын

I have no questions if you watch it. So please watch

@sohamgaud7120

2 жыл бұрын

@@robojax I have watched your full video but just for confirmation 😜

I already killed 3 of these for my 2s router ups. It cant handle 2a at 9 or 12v input

Ahmed bro can I use tp5100 for drilling machine. I want to replace 2 lithium batteries and same time I want to replace bms also do u think it will work...

@robojax

2 жыл бұрын

It doesn’t matter where you use it. I have shown voltage and maximum current. If you application need equal or less than the current and voltage is the same, then yes you can use it.

@inayath30

2 жыл бұрын

@@robojax thank you brother.. I will try.. jazakallah.. and I did subscribe u r channel also..

Do you know any cheap 2s (8.4V) charger powered (input) max 24V-25V?

@robojax

Жыл бұрын

you can't get such a thing. you need to get Step down converter and put it before this charger.

@TheLukalago

Жыл бұрын

@@robojax ok, that's what I thought

Can we charge 2s battery with 5v, or only 1s can be charged with 5v?

@robojax

Жыл бұрын

You have not watched the video. Please watch to get your answer

How much Amps cells can charge at once (In parallel) ?

@robojax

2 жыл бұрын

I believe I have tested and shown maximum current. it is in the title as well. So when you connect two cells in parallel, the maximum will be divided by 2.

How do we limit the charge current to say 1A maximum?

@robojax

2 жыл бұрын

you need a power supply with contestant current or CC. Search my channel. Here is how to find Specific KZread Video in a channel bit.ly/findKZreadVideo

Can this module be connected in parallel, so that the charging current can be above 2 amperes?

@robojax

2 жыл бұрын

Yea it can.

@rzq8896

2 жыл бұрын

@@robojax Then, is it fine to charge 2x 18650 battery (in series) with 4 amps of current?

@robojax

2 жыл бұрын

it is very tricky. don't use it in parallel or series. get different module.

My question is my sony srs xb 32 battery 5 pin connector 2 red wire 2 black wire 1 yellow wire .. how it works yellow wire .pls reply me

@robojax

4 ай бұрын

I am not sure about that model, each battery cell needs one wire and we need one common ground.

@sandeepsalaria9518

4 ай бұрын

@@robojax without ground new bms other modal it was working yes or no

@robojax

4 ай бұрын

Without ground means you want not turning a light with one wire. No.

Can i use this on 32650 Lipo4 3.2v?

@robojax

2 жыл бұрын

32659 is just physical size. Village is the same. Yes

Kinda bit dissapointed you havent tried connecting those in parallel to see if it gives 4A .. or tried connecting 2of those 2s in series for 4s charger.. :( Or even better I need a 7s charger.. so output voltage 29.4v Would 4 of them work combining 3 in 8.4 and one in 4.2? Or is there a diferent module that is cheaper? Can I use 7 of these in 8.4v for 58.8v e bike charger constant 2A? That would be a cheap Af solution Please let me know Edit: also. In theory if the charger can charge 8.4v at 2A it's 16.8W of power. This means this charger could be modified to charge 4A 4.2v cell? With those resistors? Please test this for us. I highly appriciate your work

@robojax

3 жыл бұрын

Parallel is not a good idea but it work. why not good idea? over time modules change the output voltage a little. that little variation in voltage causes the current to flow from ONE into the OHTHER and that is waste of energy. Very few like less than 0.1% of people will configure this for higher current.

@eko653

3 жыл бұрын

@@robojax but is it possle for high current?

@robojax

3 жыл бұрын

you want to me to repeat my previous comment. yes and no. Read it please.

Is that thermal imager any device? Or mobile application?🤔

@robojax

3 жыл бұрын

It it a thermal camera, I just added the link to the device in the description of this video.

I'm using this module to charge li-po battery 6000mAh with 2x4.5W solar panels in parallel can you tell what's the efficiency of this module?

@robojax

3 жыл бұрын

I just added the efficiency graph in the resources page. the link is in the description. You can see other files and datasheet.

@paveljelinek772

3 жыл бұрын

@@robojax ok thanx.. I'm gonna use a different method to my project.. since mppt is expensive, i'm gonna either connect my FV panels directly to powerbank module's mUsb with a switch (i'm afraid of current flowing into them when charging from a wall, since current always go the lowest resistance path) or using buck with 5V 3A USB out and then connecting to mUsb on pb module..