The water measured at 1593 Which Is Not good. The meter DID NOT read 1.5; it read 1593 (One thousand Five Hundred Ninety Three)ppm. Which is insanely high. Regular tap water should not be that high, nor will regular tap water read 1.5 (One point Five) that's insanely low and usually requires a reverse osmosis water filtration system. Tap water should be around 80ppm - 300ppm; is low but possible, my tap water is around 180-ppm200ppm. My Reverse Osmosis Filtration Water is at about 20ppm. Your device needs some recalibration

What an amazing demonstration

Thank you much for your very informative information I just purchased one from Amazon, the same one.

That was cool. Thank you 🙏🏾.

thanks a lot for sharing this

fantastic; cheers

Thank you!

@chihanecreativetechno7604

3 жыл бұрын

Ur very welcome

thanks for the video, I think you should not dip it over the immersion line. See the manual.

@nikolasmaes99

11 ай бұрын

Yeah noticed that too. It's probably fine, it's still closed solid plastic

So if my Tap water is 0067 ppm & EC IS 0124 RAIN water is PPM 0074 EC 0149 There's neally double mine. what does that mean

Understandable explanation, thank you.

What is the chart for EC range of fruit trees?

Salam, So TDS, total dissolved solids, output is in PPM? And EC is a an extra feature of the device, Electric Conductivity? Chokran

Do you know how to caludrate this exact PPM metre? I have the same one but I don't know how to calibrate it

@chihanecreativetechno7604

3 жыл бұрын

hi for this devise it the instruction guide says this devise has an automatic calibration feature .but only on ppm wich u cant calibrate. EC yes .the calibration prosess is quite simple what you need to do is buy the 1413 solution put 250 ml in a glass and put ur meter in -you go on ec mode -you press the cal button for 3 to 5 second and hold it in once you have done that the reading start to flash -press the cal button again with up arrow to increase the value one step at the time until it flash now u go up once at the time or press and hold the button and it will go up continously until u get 1413 then release , leave it to flash once it stop flashing that it its now calibrated .press mode button you will have 704 ppm .now ur device is calibrated .hope this will help u pleasr let me know .regards

Thank you

What kinda battery does it take?

Great video

@chihanecreativetechno7604

3 жыл бұрын

Cheers gunga

How do you clean the electrodes after each use?

@chihanecreativetechno7604

2 жыл бұрын

Hi sorry about the delay U can clean them with dry and soft tissue

👍👍

Mines is not reading it just stays on 0 and the green light stays on

First of all, I would like to thank you for your videos.I have a question? I bought one from aliexpress and i did not find its battery.where can i find it?

@chihanecreativetechno7604

2 жыл бұрын

Hi if ur in the uk u can find them in pound land they cost only 1 quid

@John-si5vs

Ай бұрын

The aliexpress units have the battery in it if it is missing it was stolen by your customs inspection service, they are thieves and do this often.

Great video. Very informative. Keep it up!

@chihanecreativetechno7604

3 жыл бұрын

Thanks a lot

ممتاز شكرا

@chihanecreativetechno7604

3 жыл бұрын

Merci

How can 1593 ppm be clean.. anything above 200 ain’t good for human consumption

What's small number in below LCD with C" mean ?

@fadiaburaid

6 ай бұрын

Temperature in Celsius

Rain water that high wow here in mru its bet 0 to 0035 ms/cm. tap water is 0078 ms/cm

Μy tap water is 0163 and the EC shows 0326. You are probably confusing the water glasses; that can't be right.

okay i have the same tester .. my water reading is 0006 ... does that mean its 6 parts per million

@ghettocowboy993

7 ай бұрын

and EC is 0012

please get rid of the annoying background music. Just tell about the device etc. Cannot concentrate with all the noise going on. Thanks

@John-si5vs

Ай бұрын

using background music is annoying and moronic

sorry I dont understand why it showed 1593 in a Tap Water and you said it is just over 1.5 and it is good? :( meanwhile in the list it gives different figure My fish tank water shows up between 400 to 750 ppm. Do you think it is okay ? I have tried tap water (that everyone can drink straightaway) and it still show around 300 . I am in London so I believe water quality is good but dont know why it show 300 to 350ppm

@chihanecreativetechno7604

3 жыл бұрын

hi sorry it took me one day to answer u i said just over 1.5 was just trying to say that its good water because it didnt reach 300 mmp .if ur fish tank shows between 400 and 750 that is not good .and it could be fir ur water or ur tds devise try with different devise .hope this could help and please let me know any update .thanks

@dependableservices01

Жыл бұрын

​@@chihanecreativetechno7604 Your meter showed 1593ppm that;s crazy high & 1.5 would be way too low. Your device needs recalibration, even the chart you used tells you those numbers are of out range

@Hampshire87

Жыл бұрын

Init 1593 does not mean 150 (1.5).. this has got me confused

Sorry, but, you mentioned a couple of times that the water was good quality. This could be false since the meter you are using does not prove the quality of water is good. A TDS/EC meter is not for testing if water quality is good. For example, the rain water could have been contaminated by stuff in the air or by whatever collected the rain water. The contamination could be something that is not dissolved in water, therefore, the meter would not read it. Although, you may be able to come to a conclusion that the water is of bad quality with a high TDS reading such as the salt water. I just don't want more people being misinformed because there is already a lot of misinformation out there regarding this subject, unfortunately. Here is a video that shows what I'm talking about. kzread.info/dash/bejne/lmeBpct_cpfImag.html

@chihanecreativetechno7604

2 жыл бұрын

Thank you so much for ur review