How to upgrade your GM 7.5” 10 bolt rear end!
Автокөліктер мен көлік құралдары
Upgrade your GM 7.5” 10 bolt rear end. Complete how to video installing larger axles, Auburn gear limited slip, ring and pinion, rebuild kit, and more.
Tips and tricks for this popular GM rear end. This is part of the ongoing S10 ls build we are building.
Stay tuned for a complete disk upgrade next.
If you like our content, do t miss any of it and subscribe today!
Пікірлер: 49
Great job guys!
@FlippinCustomized
3 жыл бұрын
Thanks bud trying to get better with the videos
Great video can't wait to see the s10 done
@FlippinCustomized
3 жыл бұрын
I will be posting rear disk brake conversion next!
@bford0896
3 жыл бұрын
@@FlippinCustomized Sweet can't wait
Great video I need more friends like steve
@FlippinCustomized
Жыл бұрын
He is the best💪
Great video. Looks like I won't have time to buy all the shit to do this, so I'm farming it out. Wish I had your setup tho!
@FlippinCustomized
2 жыл бұрын
Thanks buddy, can you borrow stuff to do it
very informational scott, i have a 10 bolt rear ,350 turbo tranny, thinking on some 355 gears for the pala
@FlippinCustomized
2 жыл бұрын
Thanks buddy
@6:45 That shim, if you use GM gears usually goes back and has the same wear pattern. Sounds crazy right? but it does work out like that.
You can get damn close by feel 💪🏻😉 safe a bunch of time. But for the vid why not
What kind of power with slicks is that 7.5 going to hold? I'm building an 85 Monte Carlo SS and I need a rear end upgrade, but I don't have the cash for a 9 inch Ford.
@FlippinCustomized
2 жыл бұрын
Same, upgraded to Richmond 28 spline. Built 5.3 going in so I guess I’ll find out 😂
@inscoredbz
5 ай бұрын
@@FlippinCustomized how has it held up?
S10 platform great choice . What's the engine size ? 6.0 ?
@FlippinCustomized
3 жыл бұрын
5.3
I havea 1991 Chevrolet S10, extended cab, 2wd that I'm building in memory of my father. That has a 4.3 non vortec V6 with the 700R4 transmission now. But wanting to know exact part numbers that you used because I want to beef up my 7.5 10 bolt to handle more and Im also gonna use a 3.73 gear ratio but I want to use posi Trac. And will be using a Cal Trac ok the rear with leaf springs.
@FlippinCustomized
2 жыл бұрын
Part numbers for what exactly
@thefbombgarage
Жыл бұрын
@@FlippinCustomized The part numbers for the upgrade parts you used would be helpful
if my 84 cutlass 7.5 rearend with open diff spins one wheel 2.25 times per driveshaft revolution, what ratio is that? can an s10 rearend be a donor for 84 cutlass or is it totally different track width as well as mounting system?
@FlippinCustomized
3 жыл бұрын
uncertain on that one, have to research it
Will this handle some aggressive launches on a FBO LS1? 370-380whp, 3100 pounds, LS7 clutch.
@FlippinCustomized
8 ай бұрын
I guess it depends on how well it hooks up but this build will have about 330 whp so we shall see
I`m doing the differential on my pontiac firebird trans am 1999. How can I tell its 7.5"? Where can I find this nr 7.5" ?
@FlippinCustomized
2 жыл бұрын
I’m sure it is, numbers stamped on housing
How much power should this setup hold I’m using a camed 5.3l am I asking for trouble?
@FlippinCustomized
2 жыл бұрын
Same set up as I’m running in this, stay tuned 🤪 should be good for 400hp
@isaiahirish6501
Жыл бұрын
@@FlippinCustomized so how long has it held up so far I was kinda wondering for my elky
Now is this a kit you part for the upgrade or did you have to buy parts separately
@FlippinCustomized
Жыл бұрын
All separate
@mrMATTHEWmay887
Жыл бұрын
See I was about to put a 5.3 L in my 2001 Chevy Blazer two wheel drive four-door then it came to my realization how much horsepower is that little stock differential going to take before for a grenades
Part # on axles 28 spline?
@FlippinCustomized
3 жыл бұрын
This had the 28 spline axles, were you looking for something specific?
@jessecarcamo1802
3 жыл бұрын
The video said it had 26 spline and you change it to 28 spline. I just wanted to know where you got the 28 spline. How much it cost and the part #
@FlippinCustomized
3 жыл бұрын
@@jessecarcamo1802 sorry about that They were Richmond 9225108 axles they were about $125 each
@jessecarcamo1802
3 жыл бұрын
@@FlippinCustomized thanks for the info that was really helpful
@FlippinCustomized
3 жыл бұрын
@@jessecarcamo1802 glad to hear it, thanks
Is it still alive? Lol
@FlippinCustomized
Жыл бұрын
Ya truck still not done 😭 paying customers come first
bad recording that white on the sides makes it worse. may be a great video but I can't watch this
@FlippinCustomized
Жыл бұрын
Sorry you feel that way, I’ve had great feedback on this video
S-10 is not a square body.
@FlippinCustomized
2 жыл бұрын
k bud, they are a small square body in my book pre 94
@seshtilirest4748
2 жыл бұрын
The body is square