Thanks for the helpful video! It seems that to keep the combustion chamber as clean as possible, you would want to have combustion on the lean side and also maximize your combustion chamber temperature. So, it seems that you want to lower the fuel pump speed (which you have done) to lean-out combustion, but also *lower* the fan speed to increase the temperature of the combustion chamber. Where is the flaw in my logic? I guess the fan controls more than the external (cooling) air, that runs over the exterior of the combustion unit to provide room heat, the fan must also provide the combustion chamber air as well?

@FuckignRuby

Жыл бұрын

if I recall, these are NA, but feel free to correct me anyone that has one of these

@fredfred2363

Жыл бұрын

Choke the combustion air input when at max fuelling like a regular oil boiler, to get the lowest volume of combustion product. That increases volumetric efficiency, increases heat exchanger temps while still keeping a lean burn👍🏻 Think of it the other way too... throwing in too much air simply blows all the hot gas straight out of the exhaust. You want to reduce exhaust gas temps to near condensing levels, while still maintaing a lean burn.

@Vortecks

Жыл бұрын

@Mobius X You are 100% correct! I'm pinning your comment, it explains the video in words 😉

@idaveuk

Жыл бұрын

I was going to use a server power supply wot you think tony ???

@yodab.at1746

Жыл бұрын

@@idaveuk any power supply that can provide 12-13 amps at 12v will work. It only pulls 10+ amps while the glow plug is on, after that the consumption drops to around 2 amps.

That was the best advice out there on the Chinese diesel heaters can't wait for your next video on the pump 👍👍

New subscriber. I ordered a heater, don’t have it yet, and I’ve been watching videos on them and I really liked your video. Straightforward, great knowledge, and a great way of explaining the info. Again thank you!!

@Vortecks

Жыл бұрын

WOW, I didn't think it made any sense (as per usual). I'm glad you understood it 😁😁

Stumbled across your video as I’ve just bought one but haven’t installed it my small workshop/shed, was gonna buy one 3 years ago for my old camper van but didn’t, so have seen hundreds of vids, was amazed at your quiet unassuming but knowledgeable presentation, blown away actually, instantly subbed and looking forward to your next blast of knowledge 👍😃

@Vortecks

Жыл бұрын

Thanks Cliff, I'm glad I could be of help. Properly tuned, these will run for a couple of years before the motor needs replacing when the brushes wear out. When I say a couple of years, I run mine probably 16 hours a day from the end of November to the end of March which is over 3,800 hours. I'll cover the installation in the next video and the servicing in the one after that.

So glad to have found this video. I have been wondering about fine tuning these units. I use one to keep my bedroom nice and warm but I have noticed it really goes through a lot of fuel on high and this video has shown me that I can really reduce my consumption and get the same heat and even better air flow in the room.

Brilliant video, I have 2 of these , one in my van and just about to install one in my house. I will be using your video to tune them now. Many thanks

Oh My Goodness! I have been hunting for MONTHS about how to stop my one of these, from fouling. I'm no mechanic, but I suspected there was a relationship between the hertz and the fan speed that was causing my issue. This is the first resource that I've found that showed a logical, simple, approach to sort the tuning...that anyone could do with a spare half hour or so. So - THANK YOU VERY MUCH! :D :D :D :D

@Vortecks

10 ай бұрын

You're very welcome, Sir 👍👍

I've been getting endless e-08's and e-10's for 3 months since getting one of these last fall -- all indicators pointed to too much fuel, but all the internet experts suggested too much air in my fuel lines, bad wires etc. Working on these changed nothing. Last night I used your setting as a starting point, 3.8 hz and 5000 rpm for the high setting, and without any other change it just started up instantly! Thank you!

@djgrazzy

Жыл бұрын

Do you have your pump on an angle 15⁰-35⁰? I just purchased a second hand campervan and suspected that was my issue and found my pump installed perfectly horizontal.

@oojimmyflip

11 ай бұрын

Thats odd because the ecu inside the heater has a pre-programmed start up sequence, it is the same start up sequence for all of them and it is not adjustable so whatever setting you set for running in the special settings menu it will not affect the fan speed on start up whatever you do, just the running speed after start up, so your tinkering must have paid off initially maybe you cleared some air from the fuel lines? or cleaned out the atomiser hole next to the glow plug ?, something you did right, or maybe you just have a tempermental heater, I had one that didnt like starting, so I cut the length of the air intake hose in half straightened it and put an old piece of stocking on the end as a filter medium with an elastic band, it starts first time every time now. when you run one straight out of the box they will start up and run fine without any hoses or exhaust pipes attached and I thinkn thats how they test them in the factory. Then we go and stick a carboard hose on the air intake and restrict the airflow with a plastic silencer, probably slightly crushing the cardboard tube in the process or bending it more than once so that it struggles to get air to the combustion chamber.

@micg

9 ай бұрын

@@oojimmyflip when I had it on default settings, it would start up the first time after install, then just smoke and pop like crazy on every subsequent attempt, over and over and over. Took everything apart, cleaned out the build-up (it wasn't burning the diesel fully), reassembled.. same thing. Double-checked literally everything, pump angle etc. was all fine. It was only once I re-did the settings as outlined here, found the sweet spot, haven't had an issue again. Didn't even have to disassemble and clean, just got going once the settings were fixed after many failed ignitions and a few flame outs on the default. Last night was the first time I had it on since May, still using the modded settings from last feb, and it fired up right away. I infer the startup sequence uses the 'low' and 'high' settings as its starting and ending point, gradually moving through the curve between these, if you think of it like a graph. Pretty sure its not just one default startup with static fan/fuel settings. If you think of the stoichiometry of the reaction here, diesel combustion needs diesel, oxygen, and heat. When the reaction isn't working right, its one of these three things that are off, can't be anything else -- in my case it was lacking sufficient oxygen for complete combustion of the given fuel amount. I think the issue is pump capacity. These kits all come with different pumps, ranging between 16-22ml per 1000 pumps. The default setting is maybe correct for one of these pump sizes, not the others. I can't remember which size I have, I think 22ml ie one of the larger ones hence me needing to get more oxygen in there per pump frequency.

@bigduphusaj162

8 ай бұрын

​@@oojimmyflipThats wrong mate. I install these on boats im a boat builder. Lots of the smaller boats we do fefurbs on the customer wants the cheap chinese ones. The start up sequence will change with the max and min rpm settings because the algorythim reduces the speed in which the fan ramps up just as it turns the plug off. For example the ones sold as 5-8kw are known for if you set the fan speed at 2500 & 5000 they have a habit of blowing out right as the plug turns off and the fan ramps up to max during start. The ramp up is too fast and the chamber usually gets blown out around the 56deg mark then you get a shutdown followed by an automatic second attempt, which sometimes gets it going. By lowering the max fan speed to 4400-4600 regardless of the fueling frequency you will automatically reduce the ramping up speed and the heater will no longer blow out at 55ish deg when the plug goes out. You can clearly hear the difference it makes and if you have anything monitoring your battery then you can see it the figure on the fan rpm ramp up spike is lower on startup. This goes for the black, blue red and newer black controller the one that has the voice speaker and connectivity. This is also the case with both aftermarket controllers ive used and the algorithms in the expensive aftermarket one (you know the one?) its automatic start up sequence is basically 4800 normal temp start up, below 0 deg intake it goes to 4600 max and on second attempt onwards the controller sets the startup speed to 5000 for the 5-8kw copy heaters. I hope you accept this as the truth because ive had to sort a load of them for the same issue especially after plug changes some dont like set to 5000 on startup because of the ramp up being so steep. cheers.

@bigduphusaj162

8 ай бұрын

​​@@micgyou are right sort of. These heaters especially the 5-8kw sold models the start up sequence algorythim will vary based on the max-min fan speed rpm, mostly the high speed setting. During the start up sequence the distinct ramp up in fan speed that coincides with the heater plug going out (around 55deg) is because the heater thinks the chamber is lit enough to run on its own. If you set the top RPM speed to 5000 and your heater runs fine then cool but if you are suffering blow outs on start up then reducing the max fan speed to 4600-4800rpm the rate in which the fan ramps up at slows so the chamber doesnt get blown out. Some of them you cannot get them going on 5000rpm setting after a plug renewal and a clean, they need backed off to 4600 to 4800 for a good 50hr before they can be sped up again. Despite what people think about these they run best with a small amount of carbon built up especially around the inner chamber where the gauze is around the turbulance plate at the bottom of the atomiser. When you clean them fully or use them from new for the first time this is why they dont burn right for about 50hr. They dont like too much carbon build up but nor do they like none. Webasto and Eberspacher know this btw thats why they have a cleaning setting now on the boats and lorries. The cleaning setting purposely gives it a rich wet burn cycle for 8 mins then roasts the thing for 3 mins then roasts it again for one minute then shuts off and restarts then sits exacly half way for 5 mins on the next start up. Hope this helps Edit: I forgot to point out on this reply that when you put the heater in a "cleaning" cycle on the newer models in lorries and boats it automatically runs the high speed fan at a heavily reduced rpm as it takes into account that you might be doing the clean cycle because it has a choppy start up. Interestingly what it does is turn the plug out at the usual temp in the start up cycle but there is a delay from them about 20 seconds before it soft ramps the fan RPM up to max.

Thanks Tony, loving mine, will definitely have a play with its settings now. Intrigued with your fuel pump upgrade, I have mine hanging on some string which has dulled down the harsh clicking 100%

@oojimmyflip

11 ай бұрын

built a box around my pump with 6mm plywood with a hole top and bottom for the fuel lines and wiring to go through, then I used 4 cup hooks to hang the box on 6mm bungee chord attached to 4 more cup hooks on the roof of the wall mounting box, cannot hear the pump clicking inside the wall box mounted to my outside wall of my house or indoors. my hearing is so sharp I can hear a pin drop outside at night. I have to sleep with earplugs in and I still wake up if I hear a noise outside through the earplugs. The pump is silent.

I have watched your video and followed along for my heater. With the minimum fan from 1,500 to 2.500 and the maximum at 5,000 rpm, I adjusted my low hz to 1.2 and the high hz down from 5,5 to 3.6 when I got the 2 red bars back. All appears to be okay, so I will see how it goes for a while. Many thanks for doing this video.

@CharredSteak

Жыл бұрын

From what I've read, I'd be careful running the fan at 5k. 4500 is as high as I have mine set

@gordonmitchell729

Жыл бұрын

@@CharredSteak good advice thank you. I have reduced the speed and it’s working better. Too much air meant that the device was putting out cooler air and now it is hotter but still safe for the casing. I have the heater on for about 16 hours each day at 1.3 and I am content with it. Thanks again friend.

@CharredSteak

Жыл бұрын

@@gordonmitchell729 Absolutely man, hopefully it'll have the motor lasting longer too

@allangoldsmith284

3 ай бұрын

Thank you for your explanation. One problem I have is in what I assume are fast forwards and can't work out what you are pressing. I haven't a clue what code 1688 meant and how you got there. There is nothing on the screen with that number. As a teacher of electronics I have learnt to go slow and assume nothing

@gordonmitchell729

3 ай бұрын

@@allangoldsmith284 I will go through my notes and hopefully I will have the details. It was a year ago when I placed the text here. I will get back to you if I can recreate the readings

Meh - that ticking sound is the sound of warmth and peace :) If i don't hear the ticking i wake up!!! Nice one Tony - keep up the excellent work! Thanks, Ringo

I'm glad to see that someone was able to make good use of theses heaters and taken the time to tune it as I've seen several of them fail (Julian Illiet had one fail)

@Vortecks

Жыл бұрын

It does take some thinking about but they're just an engine that relies on air and fuel. Being an ex car mechanic helped understand where it was going wrong. I've wanted to shout at Julian when I saw the smoke coming from his, I get zero smoke on startup or shutdown.

Great stuff - very useful. Thanks so much for uploading. 🙂

This is a very helpful video. Thanks for making it!

I've just installed one of these and will tune as you suggest, thank you. Mine's in a large workshop so space not massive issue so my next step is to try playing with exhaust heat exchanging. I appreciate that whatever I do can't create any more back-pressure than the supplied exhaust tubing, but my thought / hope is that extracting heat from the exhaust will drop pressure if anything (it's effectively a charge intercooler) whilst enabling the harvest of some waste exhaust heat.

@Vortecks

Жыл бұрын

Yes, using the exhaust as a heat exchanger is something I want to improve although I think I've got as much as I can out of it. I'm using 32mm (I think) copper tubing which I had to silver solder together. As long as you tune the heater again after you've connected it, you'll be fine. Mine inevitably does produce a small amount of back pressure but it's been running for over 12 months like that and zero build-up.

@rusty911s2

Жыл бұрын

@@Vortecks Interesting, have you got that on a YT Vid? Would love to see what you've done. I've got a few ideas but annoyingly only thought about doing something after the heater was installed, so although I have options, they're not unlimited.

That’s pretty good explanation of how to tune it. My 5kw is on a max of 3.3 at the moment as my fan speed is 4600 max I didn’t think they liked 5000 but it sounds like yours has lasted okay so might push it higher. I’ve had terrible carbon in mine but its getting better now the mixture is leaner. Thanks for the video.

@Vortecks

Жыл бұрын

They will all go to 5000rpm but different manufacturers have different default values that get them all running in the test room. Different altitudes and air conditions need different air/fuel mixtures so the manufacturer of yours might have been at a different altitude or in a vacuum 😁 My suggestion is, strip it down and clean it. I will be doing a video on it, it's not hard.

@julias-shed

Жыл бұрын

@@Vortecks I have just cleaned it. As I said it's getting better as the mixture is leaned out. It did start off as an 8kw with the usual over the top settings so it's taken a while to get it to a decent setup. I wish I'd seen your video a year ago it would have saved a lot of stress 😀

@Dirt-Diggler

Жыл бұрын

@@julias-shed that's another issue with Chinese knock offs, they lie ! There is not or ever has been an 8 KW 😏 these are copies of the eber 2KW and 5KW heaters, the Chinese fall into the group who think more fuel equals more heat, 8KW is just a 5KW run at a higher pump dose rate and "sometimes" a higher fan speed, this either soots up or the fan bearings go, usually because the brush end bearing gets full of brush dust due to the motor overspending and prematurely wearing out the brushes 👍

@Vortecks

Жыл бұрын

@@Dirt-Diggler Some mainboards & LCDs allow a fan speed of 5500 RPM with an increased pump speed. I might be wrong, but I think these are the ones marketed as the 8kW version. Last year, I tested a 5kW which goes to 5500 RPM and it will just about hold combustion at 5500 RPM and 5.3hz. The only trouble is, some of the combustion happens outside the flame tube and goes directly into the exhaust and the exhaust was hitting 280C. It 'might' be the equivalent of 8kW in total but there's probably 3kW which is directly pumped into the exhaust. Very dangerous.

@bigduphusaj162

8 ай бұрын

they dont like 5000 none of them do. The 5000 is only for a badly made machine. The startup sequence rpm ramp speed on 5000 runs them to lean full stop. From the 55deg mark when the plug extinguishes and it ramps up the fan speed to max because it thinks its lit, you are merely running lean as the air in the AFR spikes massively. This has been proven by countless people with proper measuring devices. The 5000 setting automatically sets the start up algorythim to ramp the the fan up quicker than it does on any other setting so its not just the max rpm effected. Anyone whos heater can run on 5000 no problem still wants to back it off a bit as it saves the plugs. i can get boats doing 3-5yr on these cheap copies and 5-7yr on the original plug on the genuine ones and i diall the smoke and smell out of them within minutes.

This sounds like a great investment with the current fuel prices and it's a lot quieter than other installs I have seen with your tuning of the system. I'm looking forward to your next video as I'm thinking about getting one of these in the future.

@Vortecks

Жыл бұрын

With very careful planning, it's very quiet in comparison. There are 4 sources of noise: The inlet, exhaust, heat outlet and the fan motor. I'll go through all of them when I can get my head around explaining it.

@timkelly5602

Жыл бұрын

i bought one recently and the ability to tune simply isn't in the controller, apparently there was a shortage of the above type controller, mine has a spanner icon instead of the cog wheel icon... not sure if that is the difference but probably be best to avoid the spanner version... i imagine the ore expensive heaters will still have this ability...

@oojimmyflip

11 ай бұрын

Dont leave it until winter they will double in price by then.

@oojimmyflip

11 ай бұрын

@@timkelly5602 I changed all my ecus and controllers to the Blue controllers with the led remote controls they are easy to use and give you readings of the core temperature and voltage on the remote fobs screen. they have a range of about 30 feet and use less complicated and cheaper tripple A batteries which last about a year. The blue controller has a matching Blue motherboard/ecu for the Heater and it is identifiyable by the silver Bi-metalic strip that crosses the blue coloured circuit board from one side to the other.

@bigduphusaj162

8 ай бұрын

they can be made very economical especially running two or muliples at a lower setting like in boats. Im a boat builder ive done hundreads of the genuine ones and maybe 30 to 40 chinese copies. I like the guy in the vid but i dont think his figures are correct and i think his heater has burned its mesh on the inside of the burner out to the point it runs at settings it shouldnt. Absolutely NO way is any fully working 5 or 8kw branded copy heater running at AFR menu 1.2hz and 2500rpm. You will instantly hit sub 110deg on any fully functioning heater even at 1.6hz if you go over about 2000rpm on the slow fan speed setting. You do need to up the stock 1500rpm speed by about 200rpm to get it running good if you extend ducting and exhausts to the limit but to gave a heater run at 2000rpm and 1.2Hz means its mesh is gone and atomiser is cheap junk. Ive no idea how hes got it to stay above 100deg burner temp at 2500 low 1.2.

Its great that there is even a function in the controls to adjust the unit for best results. Great info, thanks. Subbed. I live in Australia, and my retail natural gas costs AUD $20 per kw/hr of heat. Diesel is AUD $2.00 per liter and makes 12 kw/hr of heat........there is no comparison.

@mathewemy

Жыл бұрын

Might want to look at your math. MJ in Vic is 3.52c and supply charge .83c per day. Diesel is around $2 so .0352 X 38 is $1.33. QLD at .06 is $2.28 but who needs much heating up there.

@wazza33racer

Жыл бұрын

@@mathewemy I did the math........converted the joules into watts etc. The thing that bumps it up a lot, is the supply charge. For a typical residential user with relatively low volume of gas, the fixed supply charge really ups the overall cost per kw/hr of heat. There are no options to avoid that supply charge other than to have the service disconnected. Furthermore, as natural gas is gobbled up by the expanding number of gas turbines being used to supplement renewables during night time and especially wind droughts.....the price is only going to go up, and up and up. Gas turbines are horribly inefficient at replacing natural gas as a heat source in heating applications........they need to burn 3 times as much to provide the same heat energy............but since they are paying a tiny fraction of the price, they dont care about the waste of energy.

Thank you! I've been looking at one of these for a van build since I found out about them.

👍keep rocking on man 👍👍👍

Thanks for the video. Seems like I'll have to do this on mine. Although I have a different style of controller, so it might take a bit of figuring out...

After running my heater all winter on factory setting, I get great results, make sure the exhaust is in a downward slant, this is where the carbon or soot buildup starts. And the most important thing is "leave it alone so you don't burn your house down"

You R the "Chinese Heater Whisperer". Thank you. Cheers from So.Calif.USA 3rd House on the Right.

Thanks mate I'd never heard of these (not the cheap ones anyway) until I saw this vid. I'm going to pull the one out of my scrap Freelander and see if I can use it cos me garage is Baltic!!!. 5kWh heat for 45p (half litre of 28 sec kerosene @ 90p per litre) instead of 1kW for 38p of leccy.

@aayt02

Жыл бұрын

Should be a way better heater than the chinese ones, i believe the land rover ones are webasto.

It's fantastic Tony

That really was helpful. Cheers 👍🔥

Often check the prices of these China heaters view to purchase. Some very interesting data you found there Tony. 👍👍👍👍👍

@Vortecks

Жыл бұрын

They are cheap if you don't get conned by things like "8kW" which doesn't exist. I'm not using any of the parts that came with the heater now, all I've got it the heater and loom, the rest of it is custom made.

@englishrupe01

Жыл бұрын

If you want one right now, i just got a complete 5kW kit off AliEx Vevor Bestautos store for 70 dollars, including delivery in 7 days. It came in 2 days. Amazing. Still available at this price right now. Can't go wrong.

I'm going to have to watch this a few times to get me head round it but thanks a lot liked and subbed I will check out any other vids now

wow, i replaced mine a few weeks ago... just tuned it and it was waaaaayyy off. i guess this explains why the exhaust on my new one was running signicantly hotter than my old one. we'll see if it soots up :P i went from 5.5hz to 2.8hz, and the bottom one stayed at 1.4hz, but i increased the low end fan a bit.

I love the tinkering and tweaking of this heater. I wonder if you were able to get the dose rate so low because you're closer to sea level. I'm over a 1000' ASL and I can't go any lower than 4.5 Ghz. Of course, the incoming air temperature might have an effect on the heat exchanger, too. Thanks for taking the time to post this. 👍

@Vortecks

Жыл бұрын

Yes, there are a lot of factors which mean you have a high pump rate - barometric air pressure, air temperature, the location of your pump in relation to the heater (some people have it 3-4ft below) blocked fuel filter, water/condensation in the fuel or very high humidity. FYI I'm 500' ASL where I am. Obviously, very cold temperatures makes diesel freeze or at least 'gum up' if the tank is outside.

@bigduphusaj162

8 ай бұрын

dont go too low AFR as they go through plugs. Regardless of fan speed if you dont run enough fuel through them they burn plugs up and the mesh doesn't last long. If its running ideal AFR wise you will be able to run the heater at a lower normal main menu Hz setting as it will be kicking out more heat for each normal heat Hz setting so you need to undertand that leaning out AFR doeant always equate to less fuel used per heat unit kicked out.

Very helpfull video thank you

What I’ve noticed with the heater is the intake “filter” is tiny. As a gear head and diesel mechanic I’d imagine that filter may be restricting the air which could cause excessive soot or carbon build up. I modified mine and it appears to run significantly better at its highest temperature setting

Thx. I will try this.

Thanks for this guide! I found the lowest RPM setting doesn't do anything, the higher RPM seems to change the min and max fan speed.

Excellent !

Thank you!

At last someone who understands AFR ! Appart from davidmcluckie and john mck 47 your the only YTer who even starts to understand it, soo many 5min experts out there 🙄 The original webasto and ebers didn't allow owners to sod about with pump speed and fan speed, they were set at the factory to give heat with a low ex emissions, something the Chinese dont really care about all that much. 90% of issues i fix are sooting up because owners fiddle with the settings or the base settings are way off, the older blue controller would let you set dose rate up to 8Htz with a max fan speed of 5500 rpm, some would only allow 5.6htz at the same rpm so no wonder they get messed up and sooty 🙄 after a clean out i reset the controller and tell owners to use the temp settings and stop messing with the dose rate 😏 or buy a decent make, webasto and eber obv, mikuni are ok, autotherm/plannar or the lavana pro series 👍 Really enjoyed that vid chap 👍 looking forward to a few more on the subject from ya 😎

@Vortecks

Жыл бұрын

Yeah, I noticed that there are a lot of people who just want to jump on the bandwagon to get a video published, it was pissing me off that there's not much info on how to use them properly so I decided to start the series. There are a lot of bad tips on how to use them and very little in the way of safety. I wish I could find the video where someone said to go into the settings, max everything out and it runs much hotter 😒 I've got every controller & mainboard there is out there now, I kept buying them from China. I was considering buying the afterburner buy it seemed like a lot of money for loads of features I wouldn't use so....... I built my own. If you go to 8:14 you can see the TX part of it on the right but I'll cover that in another video 😉

@Dirt-Diggler

Жыл бұрын

@@Vortecks I've gone the total opposite from the afterburner in that all i have is an on off switch with remote activation and a normal 2 wire stat in the van but my own build is a rather old mikuni i saved and refurbished from a narrow boat who changed it for a cheap Chinese unit cos it was £15 cheaper than servicing the heater he already owned 🙄 his loss my gain 😎 i got paid to change in the new unit and got to keep the old one, i removed a webasto from my van and use that for back up heat in winter at home 👍

well done!

Bloody brilliant. 🥳 Got one in my van. Thank you for setting your mind to these heaters 😁 Is that one of James's fuel pumps 🤔

@Vortecks

Жыл бұрын

Yes mate, it's one of his pumps from when he first started doing them. He's grown the range now so I really hope his sales rocket when I release his details.

@johnmalone5608

Жыл бұрын

Any links to the fuel pump please.....if the guy can handle the orders 😉

I run mine on 0.8Hz and 1500RPM. It shows only 1 red bar or no red bar at all when it's below 0*C but never had any issue with carbon buildup. However running at around 3Hz or above without adjusting max Hz did indeed extinguished the heater and made impossible to reignite. Fortunately I was able to make it run again by blowing some air with industrial vacuum cleaner thru exhaust pipe and them pull the air when the heater was trying to ignite.

In your next video, could you please show your installation invluding which heater you are using. Thanks alot.

@Vortecks

Жыл бұрын

I've got to cover everything in sections, people don't like to see everything at once. Next time, I'll be covering the pump. It's just a standard 5kW diesel heater, they're everywhere and they're all the same. Don't be conned by the 8kW version, there is no such thing. It's just a 5kW with an 8kW badge.

Mine had been running great for quite awhile. Then we got some extreme temperatures and I think the gummed up diesel clogged some things. I cleaned everything out the best way I knew how. Finally got it to start again. It ran for a few days. Woke up this morning to a chilly home. Noticed the diesel heater had stopped working again. I pulled it all apart, cleaned it up and it fired up immediately. Thought all was well, but then I noticed the combustion chamber temperature was steadily dropping 2 Celsius (from 176 ish) every 10 minutes. I finally turned it off at 138 C and took it apart again. It has just as much soot as it did over the few days that it has been running since I cleaned it last. Prior to that one temperature drop, it had been running near mint. No carbon buildup to be seen.... I'm currently lost as to what is wrong. I have no idea why it's suddenly plaguing me with issues now...

Looking forward to the silent oil pump

I have one in a van and just bought one for domestic. I was interested in using a Peristaltic Pump instead of the noisy pump. Although in van with plenty of insulation can barely hear it.

I've found a the low end of these settings I get higher CO readings from the exhaust and fumes start to smell , do you think the rpm of the fan is cooling the flame zone + pushing the unburnt fuel out of the chamber to quickly ?

Great tony I have just got mine not set up yet very very interested about the upgrades you done to yours keep us updated cheers

@Vortecks

Жыл бұрын

I will mate. Once you set them up properly, they'll run maintenance free for a couple of years before you have to change the fan motor.

Great video! if the power is removed/interrupted from the heater will the adjusted settings memory be lost and return to default settings? or does the memory store and the adjusted settings are still present after power is restored. Thanks!

Not long had mine. set at 1.2hz it flicks between 1 red and no red bars. I figured it may be due to the fan speed difference, like a poor A/F mix. upped my min fan speed to 2600 and it struggled to fire up. had to choke the inlet a couple of time to get the flame lit. lowering it back down to 1600 and it fired up. but still not operating at full temperature. Will be running on kerosene soon, so hopefully that burns clean enough to prevent any coking

@kareljansen3992

Жыл бұрын

I have the same problem, I guess ours doenst like to get to low in temperature, my stats are 1.1 at 1500 rpm and 3.5 at 4000 rpm works alright!

@mrpdude84

Жыл бұрын

@@kareljansen3992 after much tweaking I still have to choke it to start. I think a combination of lots of running at 1.2hz and a one off stint with a couple of liters of veggie oil has sooted up the mesh thing, I'll get it apart at some point and see what the insides look like. Before the veggie oil it ran fine, albeit at a lower temperature.

thanks

Will the settings save or so I have to do it every time I use it? It will not be plugged into a power source all the time…

Thanks for posting, possibly the neatest home install I've seen so far. I've looked at the comments and can't see any more info on the fuel pump, are they available to buy? I plan on using mine to heat a large kitchen, I would be interested to see how you heat more than one room with a single unit :)

@Vortecks

Жыл бұрын

It's embarrassing but I might show it. I've used the splitter tube and hung 2 lengths of insulated 80mm tubing across the ceiling because I can't gain access above it. Come the spring, I'll simply take it down, compress the tubing back into the box..... job done. We have to make sacrifices to affordably keep warm.

@crustysherrifsbadge

Жыл бұрын

I’ve made a plywood box for the heater, located it on the patio, plan to run the flexi pipe through the wall and vent from under the kitchen unit kick boards. Desperately seeking a quiet fuel pump.

@darrien28

10 ай бұрын

that's simply practical and brilliant. Sure you're not a Kiwi? *chuckle @@Vortecks

1/3rd more efficiency is not to be sniffed at, even if you had the sniffles, Looking forward to the next vid on these cos I'm thinking of getting one.

@Vortecks

Жыл бұрын

Absolutely not. Mine is costing me £2 per day to heat 2 rooms now 😁

@englishrupe01

Жыл бұрын

As i just wrote above, if you want one right now, i just got a complete 5kW kit off AliEx Vevor Bestautos store for 70 dollars, including delivery in 7 days. It came in 2 days. Amazing. Still available at this price right now. Don't forget to get the 5 dollars off coupon, if you get it. Can't go wrong at that price.

Hi, did you ask about production of the quiet pump? I have ordered my heater and it will arrive in a few days. Your system looks great, so I will see about tuning my 5-8kw when it up and running. Thank you.

@Vortecks

Жыл бұрын

I'm waiting to hear back from him. He has various models available and also, a marine version for fitting in boats now. As soon as I get the green light, I'll make another video.

@gordonmitchell729

Жыл бұрын

@@Vortecks Excellent; I'll be watching lol. Thank you.

interesting. I wonder, could it be fine tuned with a lamba sensor like they use for car exhausts (of course you should know the afr ratio for this type of fuel)

I have a 5kw version and I haven't had issues with it sooting up or smoking. The mixture is about right. After last season there was little build up and it wasn't black more grey. My fuel tank is about 4ft below the unit and it makes me wonder if the height you draw the fuel affects fueling. I already know that if your tank is above the pump it does flood through. Or maybe I was just lucky.

@Vortecks

Жыл бұрын

Yes, having the pump lower down reduces fuel delivery. If you put the pump any higher, you'll probably find that it starts choking it. I think you were lucky with the placement of everything, so don't change a thing 😁

@dr_jaymz

Жыл бұрын

@@Vortecks I screwed it to the wall so it isn't going anywhere - but I think its the fuel head height that matters. The other thing that can affect it is any changes to the inlet and exhaust circuit. So for example, adding a different silencer or changing the pipe length may reduce the air mass and make it over rich. But also as the combustion chamber soot's up it may also cause it to over fuel and I bet that will be a positive feedback of doom. As they have no mixture control they probably should be set up to be quite lean. I saw someone using a lambda probe to get 15:1 at which point it smokes - I think it should be closer to 20:1, I think that 15:1 only really applies to fixed volume combustion like a cylinder than a flame in a tube where you will have an excess of oxygen.

@dr_jaymz

Жыл бұрын

@@Vortecks What I could do is get one of those pumps and pump the fuel 1ft uphill and then 6ft uphill and measure the fuel delivered in 10 mins say.

@Coladudetje

Жыл бұрын

Also 5kw heater, Ive read before 3.6-3.8 hz is most efficient in other videos, i also tested it out it saves fuel and theres a very slight black smoke i see out of chimney when u got it at 5-5.5hz. I just almost got mad now from fuel pump noises. Theres also a very good method of tuning when u buy some cheap chinese co meter and if you put it at high you see like 10k ppm and at low 1000 ppm and when its arround 3.6 hz you get 400 ppm...

Thank you for the video. I picked up a used one. Is it hard to take it apart to check and Clean out the soot if need be?

Twa... Just kidding m8 😂 , great video, i look forward to the next one.

OMG!!! You sound like Rob Halford! \m/

Really helpful video. Thank you. I had previously stripped down, cleaned and rebuilt my heater 6 times due to it running too lean and thus being overwhelmed by carbon build up. Not anymore thanks to this information! FYI: 8kw heater set at 5.2Hz (default 5.5Hz) and Min. fan speed now set at 2000RPM and Max. at 5000RPM (1650RPM and 4500RPM were the defaults). Now works a charm and havn't needed to clean it since, even running at low speeds all day. But from reading other's comments on fan speed, it seems that I should be at 4500?? to make it last longer + higher temp? I am at sea level (+1m) if that makes any difference, i don't know.

actually the first p for pump speed is the startup pump speed to heat it up. also it runs better with the fan speed set at 5500 instead of 5000. i set my glowplug to 4 out of 6 and my maximum pump speed to 5 instead of 5.5. my startup pump speed is set at 1.8. with that being said it never smokes on startup and running temperature. ive ran about 40 litres so far and it runs great

@bigduphusaj162

8 ай бұрын

5500 is wild mate for any of them. You will burn pluga out per 3 month

Hey Tony, where did you route the exhaust?

Another way to get less fuel to the heater is get a smaller pump. My 2kw came with 18.5 written on it. My 5 & 8kw came with 22 written on it. This will help those that have a different controller and can't adjust the Hertz or fan speed.

Ah this great, bought 5~8kw unit for my garage a couple of weeks ago, it's brilliant but the instructions are terrible. Ordered the monoxide detector with it 🙂

@Vortecks

Жыл бұрын

The instructions are bloody useless. Hopefully, I'll be able to fill in the massive gaps on how to use them, clean them and set them up for perfection 😉

@Dirt-Diggler

Жыл бұрын

@@Vortecks i quite enjoy a "chinglish" set of instructions 👍 usually they are funny as fook 🤣 👍

Great video, Got my interest in buying one. What make and model do you have Tony ? Thanks

@Vortecks

Жыл бұрын

Mine's just a standard 5kW heater mate, they're all the same. Don't be fooled by the 8kW version, there is no such thing. The 8kW and 5kW are identical - it's just a sales con. All I have left of the original heater, is the wiring loom and heater itself. The rest of it is absolute junk and actually makes it more noisy. The inlet and baffle thing howls, the exhaust pipe howls and the hot air tube they give you is way too short. Buy a standard 5kW one - colour and paint job doesn't matter but make sure it has the same controller as mine, I have something extra to show everyone when I get round to it.

Is that a 8266 or esp32? If so what sketch you running on it

I've got a 5kw in my motorhome that to be honest is still not great (had a 2kw at first but upgraded it). I've followed your video but it doesn't seem to make any difference. No matter hiw low I turn the hz down on either max or min it doesn't put any of the red bars out. Also if I adjust the settings, then go out and back into them again, they go back to default as if they haven't saved. Am I doing something wrong?

What’s the best tune it plays ? Any bagpipe tunes ? Thanks

Did u do a video on the pump gadget

I run 5 CDH heaters, and all heaters have run very well, producing lots of heat at all settings. Any setting under 3 will produce sooting, and eventual failure to ignite. Looking at your burn chamber, I would guess it has been run at the lower end of the fuel setting.

First! Awesome! Also I have one of these, & have often wondered. CO detector directly in the exhaust? Nada.

@Vortecks

Жыл бұрын

If you put it directly in the exhaust, it'll be going off constantly. I measure at around 500mm from the exhaust where it has time to mix with air. These are technically a jet engine without the compressor and no jet engine on earth would pass any CO tests like that.

Great video,very helpful just cleaned mine out full of carbon just like yours. Do you know what the PF 1-6 is? I have this on my controller when I scroll through the settings SN 1 or 2 (is magnets) then the PF comes up and I dont know what it is for. I am ready to reset following your suggestions.

@Vortecks

Жыл бұрын

I think PF is something to do with plateau mode where it automatically slows down or speeds up to get the temperature right. Don't touch it if everything works.

Top video, very well done. Regarding 1/7 cost of electric heating (@ 9m21s), is this based on a resistive heater or a heat pump/refrigeration heater? Also, what electricity per kw/hr and diesel per litre prices is that based on?

@Vortecks

Жыл бұрын

It's based on resistive, I'm electric only. I measured it at 46p which is what I'm paying. I know it doesn't take into account the Energy Price Guarantee but that's a rebate and not guaranteed for ever. I pay around £1.68 / litre. Kerosine is much cleaner and cheaper if you can find it, it's around £1.27

@jimmybrad156

Жыл бұрын

@@Vortecks Is that 0.46 GBP per kilowatt-hour?

@Vortecks

Жыл бұрын

@@jimmybrad156 Yes, sadly.

@concerneddad5561

Жыл бұрын

If your buy a refurb 600ltr IBC you can get a 500ltr minimum delivery of home heating oil, kerosene etc for £0.80 at todays prices from Home Fuels Direct UK this will significantly reduce the running cost. An IBC is approx size of a pallet cubed. Hope this helps. 500Ltr should get you from Oct to Mar 12hrs a day running at setting 3 with a lean burn. If my maths is right.

Thanks for the info👍 Will try this tomorrow. Is urs a 5kw?

Does anyone else's control unit display the pulse rate in numbers 1 - 10 instead of actual Hz?? Is there any way to change this?

Help ! Why my new 2 kw caravan diesel heater emits very heavy smoke when I started?

You earned a subscriber here! I just bought my second one of these heaters. I have a bit of an out there idea for a project with one of these.. Thinking of trying to convert one to a waste oil heater. But instead of pumping the oil into the heater itself I’d pump it to a separate external burn chamber and route what would be the heat output side into a pipe to be the combustion air for the waste oil. Wondering if the temperature sensor is the main or only sensor I would need to move or “fool” to achieve this unit essentially regulating a fire that’s not contained in the unit. I know this is crazy talk but I’ve pondered it a while and I’m a bit of a fabricator. Any thoughts on possible error codes or problems I would come across that would shut the unit down. Thanks

That's a nice lcd screen..so how youtube works is to actually see how its done

Great video. Excellent advice about the settings. Give or take a few factors, those are good presents. I find that mine requires a little adjusting throughout the heating season. Cow tipping high winds and barometric pressure and every now and again the fuel isn't what it should be. Mine is running 24/7 until spring. Every 30 hrs I'll turn it all the way up for 20-30 minutes and then back to whatever setting is comfortable. Make it a habit to continually remind the sheeple about safety and good old fashion common sense. Otherwise, we all know what happened to other great products that got into the hands of the clueless. Thank you for sharing .

@Vortecks

Жыл бұрын

Yes, barometric pressure is the possible cause of 90% of the sooting. The manufacturers set a default value which makes them run in their location but that setting doesn't work for most people. Unfortunately, Curtis...... common sense no longer exists but I will keep reminding people of the dangers 😉

@Vortecks

Жыл бұрын

If it's orange, it's probably biodiesel or red diesel that's had the dye removed.

@Dirt-Diggler

Жыл бұрын

@@Underground-Electronic-Music could be the winter diesel additives 🤔 winter diesel has antiwaxing additives compared to summer diesel 🤞 hopefully they haven't had red in the tank , try explaining to DVSA it was the fuel stations fault when they dip your tank 🙄 👍😁👍

@martinmclaren2833

Жыл бұрын

sheeple? This is a video about diesel heaters not the new world order!

Ahh. You have the same silent pulsing unit as i do :) from a certain Mr James 😁

what is the nodemcu for?

Thanks for your great video, I have ordered one of these for my garage, I will use your advice to dial it in. I would like to ask about the consumption, you mention that it uses 1/7 of the price of electric heating. Is that compared to regular electric radiators or a heat pump? Cheers.

@Vortecks

Жыл бұрын

It's based on resistive heating (electric fire). If you have a look further down the comments, I did a breakdown where someone else asked the same question.

@christiantrab6160

Жыл бұрын

@@Vortecks Great, thanks!

this made it clear as mud

@Vortecks

5 күн бұрын

Excellent

I would really like to change settings as you have however i found out that my vevor 5kw heater recently purchased uses this new style controller. Same appearance wise. No hz or speed settings available unfortunately. Very limited functions. Hoping it is set to burn proper and clean but unsure. Any suggestions on purchasing the appropriate parts to have the adjustability ? thanks for the video.

Works good on kerosene but I mix with a bit oil to lubricate the pump

@Vortecks

Жыл бұрын

I wish I could get kerosene 😒

is there something else going on with hz/rpm settings when in temperature mode? while in temperature mode i set the desired temperature way high, like 30C so it would be in high mode. Then I went into settings and as I changed low side hz, i could hear the fan ramp up and down (while it was/should be at max) I would have expected when in temp mode, running at high, the low side would not impact the fan RPM at high side.

Been trying to do this all day!! I have set it to these settings, but have found that if I run it on hz it runs terrible and smells very rich, if I swap it over to c° it runs fine and no smell!! I just don't understand it 🙄

Just spent most of the weekend fitting what looks to be the exact same model in my shed. It worked for 6 minutes then error 8!!! I didn’t even know they needed tuning? The instructions are poorly translated. I didn’t think about a carbon monoxide alarm, do you have a link to one? Subscribed.👍

@Vortecks

Жыл бұрын

Error 8 is a fuel problem so it's got to be the pump. Make sure you don't have any air bubbles trapped inside it. Change the orientation, wait a bit, change it back, give it a tap and that should cure it. Failing that, hold it vertically so the outlet is at its highest point and give it a few taps with something heavy 😊 This is the alarm I bought www.amazon.co.uk/FireAngel-CO-9XT-FF-Carbon-Monoxide-Sealed/dp/B00SB8VSPO

Hey Vortecks, i think itd be hilarious if you made a himo h1 folding bike faster, i loved your m365 series cant wait for more silly ev vids.

@Vortecks

Жыл бұрын

I'm making my own custom frame out of carbon fibre soon. I need it to weigh less than 15kg and produce the same power as the FQS I built.

The newe vevors come with bluetooth capability, do the blutooth ones tune themselves? Bluetooth show elevation on it.

How long should you wait for a bar change before lowering the max hrz setting each time?

@Vortecks

Жыл бұрын

I waited a couple of minutes which seems like an eternity!

Hello I wonder could you help I have the choice big buying a what I'm told 5 kw heater adjustable between 5 kw and 2 kw or a 8 kw adjustable between 8 and 5kw red one all in one same price on eBay from China what do you think. Thanks

Trying to figure out and get my head around what your doing hear in regards to having to knock it down in hz on that pump to only put it back up again? Are you basically saying to lower the pump speed while increasing the over all fan speed? And thanks for the video its very informative. Just trying to get my head around this.

@Vortecks

Жыл бұрын

It's hard to explain unless you know what AFR is (Air Fuel Ratio) When you're changing the min/max pump speed, if you turn the pump speed down, the fan speed reduces in proportion and it may go below the setting of the minimum fan speed. Setting the fan speed at 2500 is just a base point, this will ensure that the fan speed won't reduce too much as to cause a flame-out when you reduce the pump speed. The minimum and maximum fan speeds (2500 - 5000 in my case) are really 0% to 100% fan speed and the pump speed (1.2 - 3.8 in my case) are really 0% to 100% pump speed. You can do it without changing the minimum fan speed but I found that it dropped the speed so low, it was useless and it caused combustion problems. I'll update the description with basic instructions on how to tune it with default fan speeds.

@neverlandio

Жыл бұрын

@@Vortecks thank you for replying. I will have a play around with this over the weekend.

I don't know what happened to mine but my temperature bars on the display are always yellow 😢

Diesel heater with 3 button control. Sorted up after running for a couple of hours. Do you have any idea how I can set fuel adjustment. Can't find anybody to help.thanks

Info on your pump your running

run on kerrosean ,no deposites or soot absolutely as clean as new in the chamber after 15 mts of running ,burns hotter too

@ciocancatalin1043

Жыл бұрын

This thing don't damage the heater?

Hold on, so you got the exhaust inside?

Hi,why my fan does not increase the speed when i rise de hz frequency pump. My pump start ticking accordint to the hz for example 4 hz but my fan still have the speed for 2.5hz and i have black smoke on exhaust because no air.Can you help me with an advice?thanks in advance.

ive just bought a all in one 8kw heater but the control only has 4 buttons and i cant find out how to get into the setting :(do you know if your control would be compatible with other heaters as i was thinking about buying the same as yours and installing it on mine so that i can access the advance menu to tone it up

@aumatt8021

6 ай бұрын

Ya I'm in the same boat and I cannot find how to tune for altitude

if you mix kerosene into your diesel, it will burn cleaner and clean out. also if you do one tank with some heat or high octane additive. that will also help clean out and burn a bit hotter. Also when tuning, other things to keep in mind is elevation and outside temp... I was in -20 the other day and it wont keep up if the fan keeps it too cold.